Supplemental Restraint System DTCS
NOTE:
Unlisted Diagnostic Trouble Codes (DTCs) are often retrieved as a result of incorrect repair procedures. Before attempting any repairs for unlisted Diagnostic Trouble Codes (DTCs), check the vehicle service history for recent repairs. For RCM Diagnostic Trouble Codes (DTCs) not listed in this chart,
- Repair all other RCM Diagnostic Trouble Codes (DTCs) before attempting to repair any Diagnostic Trouble Codes (DTCs) not listed in this chart.
- If no other RCM Diagnostic Trouble Codes (DTCs) are retrieved, CLEAR the RCM Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the RCM Diagnostic Trouble Codes (DTCs) return, VERIFY that the RCM is the correct part number for the vehicle application, and INSTALL As-Built data following scan tool instructions under Module Programming > As-Built.
- Inspect the RCM and RCM connectors for any damaged pins or connections.
Diagnostic Trouble Code Chart
| DTC | Description | Action |
|---|---|---|
| B11D8:01 | Restraint Event Notification: General Electrical Failure | GO to Pinpoint Test BH |
| B1262:92 | Crash Input Mismatch - CAN Active, Hardware Inactive: Performance Or Incorrect Operation | GO to Pinpoint Test BH |
| B00D5:01 | Restraint System Passenger Disable Indicator: General Electrical Failure | GO to Pinpoint Test Q |
| B1202:01 | Restraint System Passenger Enable Indicator: General Electrical Failure | GO to Pinpoint Test R |
| B0061:11 | Passenger Seatbelt Tension Sensor: Circuit Short to Ground | GO to Pinpoint Test AX |
| B0061:12 | Passenger Seatbelt Tension Sensor: Circuit Short to Battery | GO to Pinpoint Test AX |
| B0061:13 | Passenger Seatbelt Tension Sensor: Circuit Open | GO to Pinpoint Test AX |
| B0061:64 | Passenger Seatbelt Tension Sensor: Signal Plausibility Failure | GO to Pinpoint Test AX |
| B00A0:62 | Occupant Classification System: Signal Compare Failure | GO to Pinpoint Test AZ |
| B00C0:11 | Passenger Seat Occupant Classification Sensor "A": Circuit Short To Ground | GO to Pinpoint Test AY |
| B00C0:12 | Passenger Seat Occupant Classification Sensor "A": Circuit Short To Battery | GO to Pinpoint Test AY |
| B00C0:16 | Passenger Seat Occupant Classification Sensor "A": Circuit Voltage Below Threshold | GO to Pinpoint Test AY |
| B00C0:49 | Passenger Seat Occupant Classification Sensor "A": Internal Electronic Failure | GO to Pinpoint Test AY |
| B00C0:7B | Passenger Seat Occupant Classification Sensor "A": Low Fluid Level | GO to Pinpoint Test AY |
| B00C2:11 | Passenger Seat Occupant Classification Sensor "C": Circuit Short to Ground | GO to Pinpoint Test BA |
| B00C2:12 | Passenger Seat Occupant Classification Sensor "C": Circuit Short to Battery | GO to Pinpoint Test BA |
| B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | GO to Pinpoint Test BB |
| U0100:00 | Lost Communication with ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test BC |
| U0151:00 | Lost Communication with Restraints Control Module: No Sub Type Information | GO to Pinpoint Test BD |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | GO to Pinpoint Test BE |
| U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test BF |
| U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test BF |
| U3000:46 | Control Module: Special Memory Failure | GO to Pinpoint Test BF |
| U3000:54 | Control Module: Missing Calibration | GO to Pinpoint Test BG |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AW |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AW |
| B1262:92 | Crash Input Mismatch - CAN Active, Hardware Inactive: Performance Or Incorrect Operation | GO to Pinpoint Test BH |
| B0001:11 | Driver Frontal Stage 1 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test A |
| B0001:12 | Driver Frontal Stage 1 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test A |
| B0001:13 | Driver Frontal Stage 1 Deployment Control: Circuit Open | GO to Pinpoint Test A |
| B0001:1A | Driver Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test A |
| B0001:2B | Driver Frontal Stage 1 Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AI |
| B0001:4A | Driver Frontal Stage 1 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B0002:11 | Driver Frontal Stage 2 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test B |
| B0002:12 | Driver Frontal Stage 2 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test B |
| B0002:13 | Driver Frontal Stage 2 Deployment Control: Circuit Open | GO to Pinpoint Test B |
| B0002:1A | Driver Frontal Stage 2 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test B |
| B0002:2B | Driver Frontal Stage 2 Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AI |
| B0002:4A | Driver Frontal Stage 2 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B0004:11 | Driver Knee Bolster Deployment Control: Circuit Short to Ground | GO to Pinpoint Test C |
| B0004:12 | Driver Knee Bolster Deployment Control: Circuit Short to Battery | GO to Pinpoint Test C |
| B0004:13 | Driver Knee Bolster Deployment Control: Circuit Open | GO to Pinpoint Test C |
| B0004:1A | Driver Knee Bolster Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test C |
| B0004:2B | Driver Knee Bolster Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AI |
| B0004:4A | Driver Knee Bolster Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B0010:11 | Passenger Frontal Stage 1 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test D |
| B0010:12 | Passenger Frontal Stage 1 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test D |
| B0010:13 | Passenger Frontal Stage 1 Deployment Control: Circuit Open | GO to Pinpoint Test D |
| B0010:1A | Passenger Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test D |
| B0010:2B | Passenger Frontal Stage 1 Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AI |
| B0010:4A | Passenger Frontal Stage 1 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B0011:11 | Passenger Frontal Stage 2 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test E |
| B0011:12 | Passenger Frontal Stage 2 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test E |
| B0011:13 | Passenger Frontal Stage 2 Deployment Control: Circuit Open | GO to Pinpoint Test E |
| B0011:1A | Passenger Frontal Stage 2 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test E |
| B0011:2B | Passenger Frontal Stage 2 Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AI |
| B0011:4A | Passenger Frontal Stage 2 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B0013:11 | Passenger Knee Bolster Deployment Control: Circuit Short to Ground | GO to Pinpoint Test F |
| B0013:12 | Passenger Knee Bolster Deployment Control: Circuit Short to Battery | GO to Pinpoint Test F |
| B0013:13 | Passenger Knee Bolster Deployment Control: Circuit Open | GO to Pinpoint Test F |
| B0013:1A | Passenger Knee Bolster Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test F |
| B0013:2B | Passenger Knee Bolster Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AI |
| B0013:4A | Passenger Knee Bolster Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B0050:11 | Driver Seatbelt Sensor: Circuit Short to Ground | GO to Pinpoint Test G |
| B0050:12 | Driver Seatbelt Sensor: Circuit Short to Battery | GO to Pinpoint Test G |
| B0050:13 | Driver Seatbelt Sensor: Circuit Open | GO to Pinpoint Test G |
| B0050:1D | Driver Seatbelt Sensor: Circuit Current Out of Range | GO to Pinpoint Test G |
| B0050:2B | Driver Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AI |
| B0050:4A | Driver Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B0052:11 | Passenger Seatbelt Sensor: Circuit Short to Ground | GO to Pinpoint Test H |
| B0052:12 | Passenger Seatbelt Sensor: Circuit Short to Battery | GO to Pinpoint Test H |
| B0052:13 | Passenger Seatbelt Sensor: Circuit Open | GO to Pinpoint Test H |
| B0052:1D | Passenger Seatbelt Sensor: Circuit Current Out of Range | GO to Pinpoint Test H |
| B0052:2B | Passenger Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AI |
| B0052:4A | Passenger Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B0070:11 | Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Ground | GO to Pinpoint Test I |
| B0070:12 | Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Battery | GO to Pinpoint Test I |
| B0070:13 | Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Open | GO to Pinpoint Test I |
| B0070:1A | Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test I |
| B0070:2B | Driver Seatbelt Pretensioner "A" Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AI |
| B0070:4A | Driver Seatbelt Pretensioner "A" Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B0072:11 | Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Ground | GO to Pinpoint Test J |
| B0072:12 | Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Battery | GO to Pinpoint Test J |
| B0072:13 | Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Open | GO to Pinpoint Test J |
| B0072:1A | Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test J |
| B0072:2B | Passenger Seatbelt Pretensioner "A" Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AI |
| B0072:4A | Passenger Seatbelt Pretensioner "A" Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B007E:11 | Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Ground | GO to Pinpoint Test K |
| B007E:12 | Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Battery | GO to Pinpoint Test K |
| B007E:13 | Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Open | GO to Pinpoint Test K |
| B007E:1A | Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test K |
| B007E:2B | Driver Seatbelt Pretensioner "C" Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AI |
| B007E:4A | Driver Seatbelt Pretensioner "C" Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B007F:11 | Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Ground | GO to Pinpoint Test L |
| B007F:12 | Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Battery | GO to Pinpoint Test L |
| B007F:13 | Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Open | GO to Pinpoint Test L |
| B007F:1A | Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test L |
| B007F:2B | Passenger Seatbelt Pretensioner "C" Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AI |
| B007F:4A | Passenger Seatbelt Pretensioner "C" Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B0082:11 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Ground | GO to Pinpoint Test M |
| B0082:12 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Battery | GO to Pinpoint Test M |
| B0082:13 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Open | GO to Pinpoint Test M |
| B0082:1A | Passenger Seatbelt Load Limiter Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test M |
| B0082:2B | Passenger Seatbelt Load Limiter Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AI |
| B0082:4A | Passenger Seatbelt Load Limiter Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B00A0:09 | Occupant Classification System: Component Failure | GO to Pinpoint Test N |
| B00A0:4A | Occupant Classification System: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B00A0:63 | Occupant Classification System: Circuit / Component Protection Time-Out | GO to Pinpoint Test N |
| B00A0:64 | Occupant Classification System: Signal Plausibility Failure | GO to Pinpoint Test N |
| B00A0:68 | Occupant Classification System: Event Information | GO to Pinpoint Test N |
| B00B5:11 | Driver Seat Track Position Restraints Sensor: Circuit Short to Ground | GO to Pinpoint Test O |
| B00B5:12 | Driver Seat Track Position Restraints Sensor: Circuit Short to Battery | GO to Pinpoint Test O |
| B00B5:13 | Driver Seat Track Position Restraints Sensor: Circuit Open | GO to Pinpoint Test O |
| B00B5:1D | Driver Seat Track Position Restraints Sensor: Circuit Current Out of Range | GO to Pinpoint Test O |
| B00B5:2B | Driver Seat Track Position Restraints Sensor: Signal Cross Coupled | GO to Pinpoint Test AI |
| B00B5:4A | Driver Seat Track Position Restraints Sensor: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B00C5:11 | Passenger Seat Track Position Restraints Sensor: Circuit Short to Ground | GO to Pinpoint Test P |
| B00C5:12 | Passenger Seat Track Position Restraints Sensor: Circuit Short to Battery | GO to Pinpoint Test P |
| B00C5:13 | Passenger Seat Track Position Restraints Sensor: Circuit Open | GO to Pinpoint Test P |
| B00C5:1D | Passenger Seat Track Position Restraints Sensor: Circuit Current Out of Range | GO to Pinpoint Test P |
| B00C5:2B | Passenger Seat Track Position Restraints Sensor: Signal Cross Coupled | GO to Pinpoint Test AI |
| B00C5:4A | Passenger Seat Track Position Restraints Sensor: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B00D5:01 | Restraint System Passenger Disable Indicator: General Electrical Failure | GO to Pinpoint Test Q |
| B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | GO to Pinpoint Test S |
| B11CF:11 | Passenger Frontal Airbag Canister Vent: Circuit Short to Ground | GO to Pinpoint Test T |
| B11CF:12 | Passenger Frontal Airbag Canister Vent: Circuit Short to Battery | GO to Pinpoint Test T |
| B11CF:13 | Passenger Frontal Airbag Canister Vent: Circuit Open | GO to Pinpoint Test T |
| B11CF:1A | Passenger Frontal Airbag Canister Vent: Circuit Resistance Below Threshold | GO to Pinpoint Test T |
| B11CF:2B | Passenger Frontal Airbag Canister Vent: Signal Cross Coupled | GO to Pinpoint Test AI |
| B11CF:4A | Passenger Frontal Airbag Canister Vent: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B11D8:12 | Restraint Event Notification: Circuit Short To Battery | GO to Pinpoint Test U |
| B11D8:14 | Restraint Event Notification: Circuit Short To Ground Or Open | GO to Pinpoint Test U |
| B1202:01 | Restraint System Passenger Enable Indicator: General Electrical Failure | GO to Pinpoint Test R |
| B1404:11 | Driver Side Airbag Deployment Control: Circuit Short to Ground | GO to Pinpoint Test V |
| B1404:12 | Driver Side Airbag Deployment Control: Circuit Short to Battery | GO to Pinpoint Test V |
| B1404:13 | Driver Side Airbag Deployment Control: Circuit Open | GO to Pinpoint Test V |
| B1404:1A | Driver Side Airbag Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test V |
| B1404:2B | Driver Side Airbag Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AI |
| B1404:4A | Driver Side Airbag Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B1405:11 | Driver Side Curtain Deployment Control 1: Circuit Short to Ground | GO to Pinpoint Test W |
| B1405:12 | Driver Side Curtain Deployment Control 1: Circuit Short to Battery | GO to Pinpoint Test W |
| B1405:13 | Driver Side Curtain Deployment Control 1: Circuit Open | GO to Pinpoint Test W |
| B1405:1A | Driver Side Curtain Deployment Control 1: Circuit Resistance Below Threshold | GO to Pinpoint Test W |
| B1405:2B | Driver Curtain Deployment Control 1: Signal Cross Coupled | GO to Pinpoint Test AI |
| B1405:4A | Driver Curtain Deployment Control 1: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B1407:11 | Passenger Side Airbag Deployment Control: Circuit Short to Ground | GO to Pinpoint Test X |
| B1407:12 | Passenger Side Airbag Deployment Control: Circuit Short to Battery | GO to Pinpoint Test X |
| B1407:13 | Passenger Side Airbag Deployment Control: Circuit Open | GO to Pinpoint Test X |
| B1407:1A | Passenger Side Airbag Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test X |
| B1407:2B | Passenger Side Airbag Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AI |
| B1407:4A | Passenger Side Airbag Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B1408:11 | Passenger Side Curtain Deployment Control 1: Circuit Short to Ground | GO to Pinpoint Test Y |
| B1408:12 | Passenger Side Curtain Deployment Control 1: Circuit Short to Battery | GO to Pinpoint Test Y |
| B1408:13 | Passenger Side Curtain Deployment Control 1: Circuit Open | GO to Pinpoint Test Y |
| B1408:1A | Passenger Side Curtain Deployment Control 1: Circuit Resistance Below Threshold | GO to Pinpoint Test Y |
| B1408:2B | Passenger Curtain Deployment Control 1: Signal Cross Coupled | GO to Pinpoint Test AI |
| B1408:4A | Passenger Curtain Deployment Control 1: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B140C:11 | Second Row Driver Side Seatbelt Sensor: Circuit Short to Ground | GO to Pinpoint Test Z |
| B140C:12 | Second Row Driver Side Seatbelt Sensor: Circuit Short to Battery | GO to Pinpoint Test Z |
| B140C:13 | Second Row Driver Side Seatbelt Sensor: Circuit Open | GO to Pinpoint Test Z |
| B140C:1D | Second Row Driver Side Seatbelt Sensor: Circuit Current Out of Range | GO to Pinpoint Test Z |
| B140C:2B | Second Row Driver Side Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AI |
| B140C:4A | Second Row Driver Side Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B140D:11 | Second Row Passenger Side Seatbelt Sensor: Circuit Short to Ground | GO to Pinpoint Test AA |
| B140D:12 | Second Row Passenger Side Seatbelt Sensor: Circuit Short to Battery | GO to Pinpoint Test AA |
| B140D:13 | Second Row Passenger Side Seatbelt Sensor: Circuit Open | GO to Pinpoint Test AA |
| B140D:1D | Second Row Passenger Side Seatbelt Sensor: Circuit Current Out of Range | GO to Pinpoint Test AA |
| B140D:2B | Second Row Passenger Side Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AI |
| B140D:4A | Second Row Passenger Side Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B1410:11 | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Short To Ground | GO to Pinpoint Test AB |
| B1410:12 | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Short To Battery | GO to Pinpoint Test AB |
| B1410:13 | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Open | GO to Pinpoint Test AB |
| B1410:1A | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test AB |
| B1410:2B | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AI |
| B1410:4A | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B1412:11 | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Circuit Short To Ground | GO to Pinpoint Test AC |
| B1412:12 | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Circuit Short To Battery | GO to Pinpoint Test AC |
| B1412:13 | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Circuit Open | GO to Pinpoint Test AC |
| B1412:1A | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test AC |
| B1412:2B | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AI |
| B1412:4A | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B1413:11 | Driver Frontal Restraints Sensor: Circuit Short to Ground | GO to Pinpoint Test AD |
| B1413:12 | Driver Frontal Restraints Sensor: Circuit Short to Battery | GO to Pinpoint Test AD |
| B1413:13 | Driver Frontal Restraints Sensor: Circuit Open | GO to Pinpoint Test AD |
| B1413:2B | Driver Frontal Restraints Sensor: Signal Cross-Coupled | GO to Pinpoint Test AI |
| B1413:4A | Driver Frontal Restraints Sensor: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B1413:81 | Driver Frontal Restraints Sensor: Invalid Serial Data Received | GO to Pinpoint Test AE |
| B1413:96 | Driver Frontal Restraints Sensor: Component Internal Failure | GO to Pinpoint Test AE |
| B1414:11 | Driver Side Restraints Sensor 1: Circuit Short to Ground | GO to Pinpoint Test AF |
| B1414:12 | Driver Side Restraints Sensor 1: Circuit Short to Battery | GO to Pinpoint Test AF |
| B1414:13 | Driver Side Restraints Sensor 1: Circuit Open | GO to Pinpoint Test AF |
| B1414:2B | Driver Side Restraints Sensor 1: Signal Cross-Coupled | GO to Pinpoint Test AI |
| B1414:4A | Driver Side Restraints Sensor 1: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B1414:81 | Driver Side Restraints Sensor 1: Invalid Serial Data Received | GO to Pinpoint Test AE |
| B1414:96 | Driver Side Restraints Sensor 1: Component Internal Failure | GO to Pinpoint Test AE |
| B1415:11 | Driver Side Restraints Sensor 2: Circuit Short to Ground | GO to Pinpoint Test AG |
| B1415:12 | Driver Side Restraints Sensor 2: Circuit Short to Battery | GO to Pinpoint Test AG |
| B1415:13 | Driver Side Restraints Sensor 2: Circuit Open | GO to Pinpoint Test AG |
| B1415:2B | Driver Side Restraints Sensor 2: Signal Cross-Coupled | GO to Pinpoint Test AI |
| B1415:4A | Driver Side Restraints Sensor 2: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B1415:81 | Driver Side Restraints Sensor 2: Invalid Serial Data Received | GO to Pinpoint Test AE |
| B1415:96 | Driver Side Restraints Sensor 2: Component Internal Failure | GO to Pinpoint Test AE |
| B1417:11 | Passenger Frontal Restraints Sensor: Circuit Short To Ground | GO to Pinpoint Test AH |
| B1417:12 | Passenger Frontal Restraints Sensor: Circuit Short To Battery | GO to Pinpoint Test AH |
| B1417:13 | Passenger Frontal Restraints Sensor: Circuit Open | GO to Pinpoint Test AH |
| B1417:2B | Passenger Frontal Restraints Sensor: Signal Cross-Coupled | GO to Pinpoint Test AI |
| B1417:4A | Passenger Frontal Restraints Sensor: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B1417:81 | Passenger Frontal Restraints Sensor: Invalid Serial Data Received | GO to Pinpoint Test AE |
| B1417:96 | Passenger Frontal Restraints Sensor: Component Internal Failure | GO to Pinpoint Test AE |
| B1418:11 | Passenger Side Restraints Sensor 1: Circuit Short to Ground | GO to Pinpoint Test AG |
| B1418:12 | Passenger Side Restraints Sensor 1: Circuit Short to Battery | GO to Pinpoint Test AG |
| B1418:13 | Passenger Side Restraints Sensor 1: Circuit Open | GO to Pinpoint Test AG |
| B1418:2B | Passenger Side Restraints Sensor 1: Signal Cross-Coupled | GO to Pinpoint Test AI |
| B1418:4A | Passenger Side Restraints Sensor 1: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B1418:81 | Passenger Side Restraints Sensor 1: Invalid Serial Data Received | GO to Pinpoint Test AE |
| B1418:96 | Passenger Side Restraints Sensor 1: Component Internal Failure | GO to Pinpoint Test AE |
| B1419:11 | Passenger Side Restraints Sensor 2: Circuit Short to Ground | GO to Pinpoint Test AF |
| B1419:12 | Passenger Side Restraints Sensor 2: Circuit Short to Battery | GO to Pinpoint Test AF |
| B1419:13 | Passenger Side Restraints Sensor 2: Circuit Open | GO to Pinpoint Test AF |
| B1419:2B | Passenger Side Restraints Sensor 2: Signal Cross-Coupled | GO to Pinpoint Test AI |
| B1419:4A | Passenger Side Restraints Sensor 2: Incorrect Component Installed | GO to Pinpoint Test AJ |
| B1419:81 | Passenger Side Restraints Sensor 2: Invalid Serial Data Received | GO to Pinpoint Test AE |
| B1419:96 | Passenger Side Restraints Sensor 2: Component Internal Failure | GO to Pinpoint Test AE |
| B142D:00 | Pyrotechnic End of Life Activation Performed: No Sub Type Information | GO to Pinpoint Test AS |
| B1492:68 | Fuel Cutoff Event: Event Information | GO to Pinpoint Test AT |
| C0061:68 | Lateral Acceleration Sensor: Event Information | GO to Pinpoint Test AK |
| C0062:68 | Longitudinal Acceleration Sensor: Event Information | GO to Pinpoint Test AK |
| C0063:68 | Yaw Rate Sensor: Event Information | GO to Pinpoint Test AK |
| C0064:68 | Roll Rate Sensor: Event Information | GO to Pinpoint Test AK |
| C0065:68 | Vertical Acceleration Sensor: Event Information | GO to Pinpoint Test AK |
| U0028:88 | Vehicle Communication Bus A: Bus Off | GO to Pinpoint Test AL |
| U0100:00 | Lost Communication with ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test AM |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test BC |
| U0140:00 | Lost Communication with Body Control Module: No Sub Type Information | GO to Pinpoint Test AN |
| U0146:00 | Lost Communication with Gateway "A": No Sub Type Information | GO to Pinpoint Test AO |
| U0154:00 | Lost Communication with Restraints Occupant Classification System Module: No Sub Type Information | GO to Pinpoint Test AP |
| U0253:00 | Lost Communication with Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AQ |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | GO to Pinpoint Test AR |
| U0401:81 | Invalid Data Received from ECM/PCM A: Invalid Serial Data Received | GO to Pinpoint Test AR |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test AR |
| U0422:81 | Invalid Data Received From Body Control Module: Invalid Serial Data Received | GO to Pinpoint Test AR |
| U0455:81 | Invalid Data Received From Restraints Occupant Classification System Module: Invalid Serial Data Received | GO to Pinpoint Test AR |
| U0554:00 | Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AR |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AU |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test AL |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test AS |
| U2300:55 | Central Configuration: Not Configured | GO to Pinpoint Test AV |
| U2300:64 | Central Configuration: Signal Plausibility Failure | GO to Pinpoint Test AV |
| U3000:04 | Control Module: System Internal Failure | GO to Pinpoint Test AS |
| U3000:46 | Control Module: Calibration / Parameter Memory Failure | GO to Pinpoint Test AS |
| U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test AS |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AW |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AW |