Parking Brake System DTCS
Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| DTC | Description | Action |
|---|---|---|
| B1111:4B | Electric Park Brake Enable:Over Temperature | GO to Pinpoint Test F |
| B1111:53 | Electric Park Brake Enable:Deactivated | GO to Pinpoint Test G |
| B1111:54 | Electric Park Brake Enable:Missing Calibration | GO to Pinpoint Test E |
| C0609:01 | Park Brake Switch Circuit:General Electrical Failure | GO to Pinpoint Test B |
| C0616:9A | Park Brake Control Module Control Circuit Performance:Component or System Operating Conditions | GO to Pinpoint Test B |
| C1034:01 | Park Brake:General Electrical Failure | GO to Pinpoint Test B |
| C1034:07 | Park Brake:Mechanical Failures | GO to Pinpoint Test K |
| C1034:13 | Park Brake:Circuit Open | GO to Pinpoint Test B |
| C1034:25 | Park Brake:Signal Shape/Waveform Failure | GO to Pinpoint Test B |
| C1034:2F | Park Brake:Signal Erratic | GO to Pinpoint Test B |
| C1034:47 | Park Brake:Watchdog/Safety μC Failure | GO to Pinpoint Test B |
| C1034:48 | Park Brake:Supervision Software Failure | GO to Pinpoint Test B |
| C1034:57 | Park Brake:Invalid/Incompatible Software Component | GO to Pinpoint Test B |
| C1034:71 | Park Brake:Actuator Stuck | GO to Pinpoint Test C |
| C1034:77 | Park Brake:Commanded Position Not Reachable | GO to Pinpoint Test C |
| C1034:78 | Park Brake:Alignment Or Adjustment Incorrect | GO to Pinpoint Test H |
| C1034:97 | Park Brake:Component or System Operation Obstructed or Blocked | GO to Pinpoint Test D |
| C1A43:98 | Motor Supply:Component or System Over Temperature | GO to Pinpoint Test D |
| C2005:18 | Right Actuator:Circuit Current Below Threshold | GO to Pinpoint Test D |
| C2005:19 | Right Actuator:Circuit Current Above Threshold | GO to Pinpoint Test D |
| C2005:77 | Right Actuator:Commanded Position Not Reachable | GO to Pinpoint Test C |
| C2005:78 | Right Actuator:Alignment Or Adjustment Incorrect | GO to Pinpoint Test A |
| C2006:18 | Left Actuator:Circuit Current Below Threshold | GO to Pinpoint Test D |
| C2006:19 | Left Actuator:Circuit Current Above Threshold | GO to Pinpoint Test D |
| C2006:77 | Left Actuator:Commanded Position Not Reachable | GO to Pinpoint Test C |
| C2006:78 | Left Actuator:Alignment Or Adjustment Incorrect | GO to Pinpoint Test A |
| C2007:13 | Right Motor:Circuit Open | GO to Pinpoint Test D |
| C2007:1C | Right Motor:Circuit Voltage Out Of Range | GO to Pinpoint Test D |
| C2007:92 | Right Motor:Performance Or Incorrect Operation | GO to Pinpoint Test D |
| C2008:13 | Left Motor:Circuit Open | GO to Pinpoint Test D |
| C2008:1C | Left Motor:Circuit Voltage Out Of Range | GO to Pinpoint Test D |
| C2008:92 | Left Motor:Performance Or Incorrect Operation | GO to Pinpoint Test D |
| U2002:00 | Switch:No Sub Type Information | GO to Pinpoint Test J |
| U2002:47 | Switch:Watchdog/Safety μC Failure | GO to Pinpoint Test B |