| B129C:12 |
Left Front Side Sensor: Circuit Short To Battery |
REFER to: Parking Aid
. |
| B129C:14 |
Left Front Side Sensor: Circuit Short To Ground or Open |
REFER to: Parking Aid
. |
| B129C:96 |
Left Front Side Sensor: Component Internal Failure |
REFER to: Parking Aid
. |
| B129D:12 |
Right Front Side Sensor: Circuit Short To Battery |
REFER to: Parking Aid
. |
| B129D:14 |
Right Front Side Sensor: Circuit Short To Ground or Open |
REFER to: Parking Aid
. |
| B129D:96 |
Left Front Side Sensor: Component Internal Failure |
REFER to: Parking Aid
. |
| B1304:00 |
Electronic Power Assisted Steering System: No Sub Type Information |
REFER to: Parking Aid
. |
| B1B36:12 |
Right Front Outer Sensor: Circuit Short To Battery |
GO to Pinpoint Test G |
| B1B36:14 |
Right Front Outer Sensor: Circuit Short To Ground or Open |
GO to Pinpoint Test H |
| B1B36:96 |
Right Front Outer Sensor: Component Internal Failure |
GO to Pinpoint Test I |
| B1B38:12 |
Right Front Inner Sensor: Circuit Short To Battery |
GO to Pinpoint Test G |
| B1B38:14 |
Right Front Inner Sensor: Circuit Short To Ground or Open |
GO to Pinpoint Test H |
| B1B38:96 |
Right Front Inner Sensor: Component Internal Failure |
GO to Pinpoint Test I |
| B1B40:12 |
Left Front Outer Sensor: Circuit Short To Battery |
GO to Pinpoint Test G |
| B1B40:14 |
Left Front Outer Sensor: Circuit Short To Ground or Open |
GO to Pinpoint Test H |
| B1B40:96 |
Left Front Outer Sensor: Component Internal Failure |
GO to Pinpoint Test I |
| B1B42:12 |
Left Front Inner Sensor: Circuit Short To Battery |
GO to Pinpoint Test G |
| B1B42:14 |
Left Front Inner Sensor: Circuit Short To Ground or Open |
GO to Pinpoint Test H |
| B1B42:96 |
Left Front Inner Sensor: Component Internal Failure |
GO to Pinpoint Test I |
| B1B44:12 |
Right Rear Outer Sensor: Circuit Short To Battery |
GO to Pinpoint Test E |
| B1B44:14 |
Right Rear Outer Sensor: Circuit Short To Ground or Open |
GO to Pinpoint Test D |
| B1B44:96 |
Right Rear Outer Sensor: Component Internal Failure |
GO to Pinpoint Test F |
| B1B46:12 |
Right Rear Inner Sensor: Circuit Short To Battery |
GO to Pinpoint Test E |
| B1B46:14 |
Right Rear Inner Sensor: Circuit Short To Ground or Open |
GO to Pinpoint Test D |
| B1B46:96 |
Right Rear Inner Sensor: Component Internal Failure |
GO to Pinpoint Test F |
| B1B48:12 |
Left Rear Outer Sensor: Circuit Short To Battery |
GO to Pinpoint Test E |
| B1B48:14 |
Left Rear Outer Sensor: Circuit Short To Ground or Open |
GO to Pinpoint Test D |
| B1B48:96 |
Left Rear Outer Sensor: Component Internal Failure |
GO to Pinpoint Test F |
| B1B50:12 |
Left Rear Inner Sensor: Circuit Short To Battery |
GO to Pinpoint Test E |
| B1B50:14 |
Left Rear Inner Sensor: Circuit Short To Ground or Open |
GO to Pinpoint Test D |
| B1B50:96 |
Left Rear Inner Sensor: Component Internal Failure |
GO to Pinpoint Test F |
| B1B57:11 |
Front Sensors Power Circuit: Circuit Short To Ground |
GO to Pinpoint Test B |
| B1B58:11 |
Rear Sensors Power Circuit: Circuit Short To Ground |
GO to Pinpoint Test C |
| U0100:00 |
Lost Communication With ECM/PCM "A": No Sub Type Information |
GO to Pinpoint Test J |
| U0121:00 |
Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information |
GO to Pinpoint Test K |
| U0131:00 |
Lost Communication With Power Steering Control Module: No Sub Type Information |
GO to Pinpoint Test L |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test M |
| U0146:00 |
Lost Communication With Gateway "A": No Sub Type Information |
GO to Pinpoint Test N |
| U0155:00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to Pinpoint Test O |
| U0212:00 |
Lost Communication With Steering Column Control Module: No Sub Type Information |
GO to Pinpoint Test P |
| U0253:00 |
Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test Q |
| U0256:00 |
Lost Communication With Front Controls Interface Module "A": No Sub Type Information |
GO to Pinpoint Test R |
| U0401:00 |
Invalid Data Received From ECM/PCM A: No Sub Type Information |
Sets in continuous memory when the PAM receives invalid network data from the PCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0415:00 |
Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information |
Sets in continuous memory when the PAM receives invalid network data from the ABS module with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0420:00 |
Invalid Data Received From Power Steering Control Module: No Sub Type Information |
A continuous and on-demand DTC that sets when the PAM receives an invalid network data from the PSCM with a faulted signal data input and or a loss of PSCM synchronization occurred. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in other modules on the network. If no Diagnostic Trouble Codes (DTCs) are present in the PSCM drive the vehicle above 50 km/h (30 mph) for a minimum distance of 1 mile while maintaining a straight ahead vehicle position for at least 30 seconds (this drive cycle needs to occur if the battery has been disconnected or if vehicle is new). If the active park assist is still inoperative and the U0420:00 DTC does not return after driving the vehicle for 1 mile and clearing Diagnostic Trouble Codes (DTCs). DIAGNOSE the observable symptom. |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
Sets in continuous memory when the PAM receives invalid network data from the BCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0423:00 |
Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information |
Sets in continuous memory when the PAM receives invalid network data from the IPC with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0429:00 |
Invalid Data Received From Steering Column Control Module: No Sub Type Information |
Sets in continuous memory when the PAM receives invalid network data from the SCCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0554:00 |
Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information |
Sets in continuous memory when the PAM receives invalid network data from the APIM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U0557:00 |
Invalid Data Received From Front Controls Interface Module "A": No Sub Type Information |
Sets in continuous memory when the PAM receives invalid network data from the FCIM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. |
| U2024:41 |
Control Module Cal-Config Data: General Checksum Failure |
CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the PAM self-test. If DTC U2024:41 is retrieved again, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. REFER to: Module Configuration - System Operation and Component Description
. REPEAT the self-test. If DTC U2024:41 is retrieved again, Refer to BCM Guided Routine
.
. |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
CHECK the vehicle service history for recent service actions related to this module. This DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. REFER to: Module Configuration - System Operation and Component Description
. If there have been no recent service actions, Refer to BCM Guided Routine
.
. |
| U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
CHECK the vehicle service history for recent service actions related to this module. This DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. REFER to: Module Configuration - System Operation and Component Description
. If there have been no recent service actions, Refer to BCM Guided Routine
.
. |
| U3000:44 |
Control Module: Data Memory Failure |
CLEAR the PAM Diagnostic Trouble Codes (DTCs) and PERFORM the PAM self-test. If DTC U3000:44, Refer to BCM Guided Routine
.
. |
| U3000:45 |
Control Module: Program Memory Failure |
CLEAR the PAM Diagnostic Trouble Codes (DTCs) and PERFORM the PAM self-test. If DTC U3000:45, Refer to BCM Guided Routine
.
. |
| U3000:46 |
Control Module: Calibration / Parameter Memory Failure |
CLEAR the PAM Diagnostic Trouble Codes (DTCs) and PERFORM the PAM self-test. If DTC U3000:46, Refer to BCM Guided Routine
.
. |