Remote Function Actuator (RFA) Module DTC Chart
Remote Function Actuator (RFA) Module DTC Chart
| DTC | Description | Action |
|---|---|---|
| B10C7:13 | Interior Trunk Antenna: Circuit Open | GO to PINPOINT TEST F . |
| B10C8:13 | Interior Centre Antenna: Circuit Open | GO to PINPOINT TEST F . |
| B10C9:13 | Interior Front Antenna: Circuit Open | GO to PINPOINT TEST F . |
| B10D7:05 | PATS Key: System Programming Failure | GO to PINPOINT TEST A . |
| B10D7:31 | PATS Key: No Signal | This DTC sets during an Remote Function Actuator (RFA) module self-test if 2 programmed Intelligent Access (IA) keys are not detected inside the vehicle. Check each IA key individually to see if it operates the vehicle. If an IA key does not operate the vehicle, program that key. Refer to KEY PROGRAMMING USING DIAGNOSTIC EQUIPMENT - INTELLIGENT ACCESS (IA) . If 2 programmed IA keys are not present inside the vehicle, disregard this DTC. |
| B10D8:51 | Passive Anti-Theft System (PATS) Key Less Than Minimum Programmed: Not Programmed | If other PATS DTCs are present, address them first. If DTC B10D8:51 is the only DTC present, PROGRAM additional keys (minimum of 2 keys must be programmed). REFER to KEY PROGRAMMING USING DIAGNOSTIC EQUIPMENT - INTELLIGENT ACCESS (IA) . CLEAR the DTCs. REPEAT the self-test. |
| B10D9:11 | PATS Transponder: Circuit Short To Ground | GO to PINPOINT TEST B . |
| B10D9:12 | PATS Transponder: Circuit Short To Battery | GO to PINPOINT TEST B . |
| B10D9:31 | PATS Transponder: No Signal | GO to PINPOINT TEST B . |
| B10D9:87 | PATS Transponder: Missing Message | GO to PINPOINT TEST B . |
| B10DA:51 | PATS PCM Identifier: Not Programmed | There is no PCM ID stored in the RFA module. CARRY OUT a parameter reset of the RFA module and the PCM, then CYCLE the ignition and make an attempt to start the vehicle. REFER to PASSIVE ANTI-THEFT SYSTEM (PATS) PARAMETER RESET - INTELLIGENT ACCESS (IA) . CLEAR the DTCs. REPEAT the self-test. |
| B10DA:61 | PATS PCM Identifier: Signal Calculation Failure | There is an incorrect PCM ID stored in the RFA module. CARRY OUT a parameter reset of the RFA module and the PCM, then CYCLE the ignition and make an attempt to start the vehicle. REFER to PASSIVE ANTI-THEFT SYSTEM (PATS) PARAMETER RESET - INTELLIGENT ACCESS (IA) . CLEAR the DTCs. REPEAT the self-test. |
| B10DA:86 | PATS PCM Identifier: Signal Invalid | There is an issue with the PCM ID stored in the RFA module. CARRY OUT a parameter reset of the RFA module and the PCM, then CYCLE the ignition and make an attempt to start the vehicle. REFER to PASSIVE ANTI-THEFT SYSTEM (PATS) PARAMETER RESET - INTELLIGENT ACCESS (IA) . CLEAR the DTCs. REPEAT the self-test. |
| B125D:11 | Ignition Run LED: Circuit Short To Ground | GO to PINPOINT TEST C . |
| B125D:15 | Ignition Run LED: Circuit Short To Battery or Open | GO to PINPOINT TEST C . |
| U0100:87 | Lost Communication With ECM/PCM "A": Missing Message |
NOTE:
If DTC B10DA:51, B10DA:61 or B10DA:86 is present, address DTC B10DA:51, B10DA:61 or B10DA:86 first. GO to PINPOINT TEST D
. |
| U201F:31 | External Receiver: No Signal | GO to PINPOINT TEST E . |
| All other DTCs | - | REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULES . |