Inspection [09/2014 - 03/2019]: Procedure
- INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Memory)
- Check the operation of the mirror surface.NOTE:
If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.
- Disconnect the outer rear view mirror assembly RH connector.
*a Component without harness connected
(Outer Rear View Mirror Assembly RH) - Apply battery voltage and check the operation of the mirror surface.
OK
Battery Connection Specified Condition Battery positive (+) → Terminal 1 (MV)
Battery negative (-) → Terminal 10 (M+)Turns upward Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 1 (MV)Turns downward Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 10 (M+)Turns left Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 9 (MH)Turns right If the result is not as specified, replace the outer rear view mirror assembly RH.
- Disconnect the outer rear view mirror assembly RH connector.
- Check the operation of the mirror heater.
- Disconnect the outer rear view mirror assembly RH connector.
*a Component without harness connected
(Outer Rear View Mirror Assembly RH) - Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition 4 (+) - 12 (-) 25°C (75°F) 3.57 to 4.83 Ω If the result is not as specified, replace the outer rear view mirror assembly RH.
- Connect a cable from the positive (+) battery terminal to terminal 4 and the negative (-) battery terminal to terminal 12, then check that the mirror becomes warm.
HINT:
It takes a short time for the mirror to become warm.
OK
Mirror becomes warm.
If the result is not as specified, replace the outer rear view mirror assembly RH.
- Disconnect the outer rear view mirror assembly RH connector.
- Check the operation of the retractable mirror.NOTE:
- Disconnect and reconnect the battery between each mirror position check.
- The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.
- If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.
- Disconnect the outer mirror actuator assembly RH connector.
*a (A) Forward position *b (B) *c (C) Driving position *d (D) *e (E) Retracted position *f Component without harness connected
(Outer Mirror Actuator Assembly RH) - For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.
OK
Battery Connection Condition Specified Condition Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Forward position (A) Moves from (A) to (E) Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Forward position (A) Does not move Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Position between forward position (A) and driving position (C) Moves from (B) to (E) Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Position between forward position (A) and driving position (C) Moves from (B) to (A) Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Driving position (C) Moves from (C) to (E) Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Driving position (C) Does not move Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Position between driving position (C) and retracted position (E) Moves from (D) to (E) Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Position between driving position (C) and retracted position (E) Moves from (D) to (C) Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Retracted position (E) Does not move Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Retracted position (E) Moves from (E) to (C) If the result is not as specified, replace the outer mirror actuator assembly RH.
- Check the operation of the mirror surface.
- INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Memory)
- Check the operation of the mirror surface.NOTE:
If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.
- Disconnect the outer rear view mirror assembly RH connector.
*a Component without harness connected
(Outer Rear View Mirror Assembly RH) - Apply battery voltage and check the operation of the mirror surface.
OK
Battery Connection Specified Condition Battery positive (+) → Terminal 1 (RMVR)
Battery negative (-) → Terminal 10 (RM+R)Turns upward Battery positive (+) → Terminal 10 (RM+R)
Battery negative (-) → Terminal 1 (RMVR)Turns downward Battery positive (+) → Terminal 9 (RMHR)
Battery negative (-) → Terminal 10 (RM+R)Turns left Battery positive (+) → Terminal 10 (RM+R)
Battery negative (-) → Terminal 9 (RMHR)Turns right If the result is not as specified, replace the outer rear view mirror assembly RH.
- Disconnect the outer rear view mirror assembly RH connector.
- Check the operation of the mirror heater.
- Disconnect the outer rear view mirror assembly RH connector.
*a Component without harness connected
(Outer Rear View Mirror Assembly RH) - Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition 4 (HTR+) - 12 (HTR-) 25°C (75°F) 3.57 to 4.83 Ω If the result is not as specified, replace the outer rear view mirror assembly RH.
- Connect a cable from the positive (+) battery terminal to terminal 4 and the negative (-) battery terminal to terminal 12, then check that the mirror becomes warm.
HINT:
It takes a short time for the mirror to become warm.
OK
Mirror becomes warm.
If the result is not as specified, replace the outer rear view mirror assembly RH.
- Disconnect the outer rear view mirror assembly RH connector.
- Check the operation of the retractable mirror.NOTE:
- Disconnect and reconnect the battery between each mirror position check.
- The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.
- If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.
- Disconnect the outer mirror actuator assembly RH connector.
*a (A) Forward position *b (B) *c (C) Driving position *d (D) *e (E) Retracted position *f Component without harness connected
(Outer Mirror Actuator Assembly RH) - For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.
OK
Battery Connection Condition Specified Condition Battery positive (+) → Terminal 3 (MR+)
Battery negative (-) → Terminal 11 (MR-)Forward position (A) Moves from (A) to (E) Battery positive (+) → Terminal 11 (MR-)
Battery negative (-) → Terminal 3 (MR+)Forward position (A) Does not move Battery positive (+) → Terminal 3 (MR+)
Battery negative (-) → Terminal 11 (MR-)Position between forward position (A) and driving position (C) Moves from (B) to (E) Battery positive (+) → Terminal 11 (MR-)
Battery negative (-) → Terminal 3 (MR+)Position between forward position (A) and driving position (C) Moves from (B) to (A) Battery positive (+) → Terminal 3 (MR+)
Battery negative (-) → Terminal 11 (MR-)Driving position (C) Moves from (C) to (E) Battery positive (+) → Terminal 11 (MR-)
Battery negative (-) → Terminal 3 (MR+)Driving position (C) Does not move Battery positive (+) → Terminal 3 (MR+)
Battery negative (-) → Terminal 11 (MR-)Position between driving position (C) and retracted position (E) Moves from (D) to (E) Battery positive (+) → Terminal 11 (MR-)
Battery negative (-) → Terminal 3 (MR+)Position between driving position (C) and retracted position (E) Moves from (D) to (C) Battery positive (+) → Terminal 3 (MR+)
Battery negative (-) → Terminal 11 (MR-)Retracted position (E) Does not move Battery positive (+) → Terminal 11 (MR-)
Battery negative (-) → Terminal 3 (MR+)Retracted position (E) Moves from (E) to (C) If the result is not as specified, replace the outer mirror actuator assembly RH.
- Check the operation of the mirror surface.
- INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Memory)
- Check the operation of the mirror surface.NOTE:
If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.
- Disconnect the outer rear view mirror assembly LH connector.
*a Component without harness connected
(Outer Rear View Mirror Assembly LH) - Apply battery voltage and check the operation of the mirror surface.
OK
Battery Connection Specified Condition Battery positive (+) → Terminal 1 (MV)
Battery negative (-) → Terminal 10 (M+)Turns upward Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 1 (MV)Turns downward Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 10 (M+)Turns right Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 9 (MH)Turns left If the result is not as specified, replace the outer rear view mirror assembly LH.
- Disconnect the outer rear view mirror assembly LH connector.
- Check the operation of the mirror heater.
- Disconnect the outer rear view mirror assembly LH connector.
*a Component without harness connected
(Outer Rear View Mirror Assembly LH) - Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition 4 (+) - 12 (-) 25°C (75°F) 3.57 to 4.83 Ω If the result is not as specified, replace the outer rear view mirror assembly LH.
- Connect a cable from the positive (+) battery terminal to terminal 4 and the negative (-) battery terminal to terminal 12, then check that the mirror becomes warm.
HINT:
It takes a short time for the mirror to become warm.
OK
Mirror becomes warm.
If the result is not as specified, replace the outer rear view mirror assembly LH.
- Disconnect the outer rear view mirror assembly LH connector.
- Check the operation of the retractable mirror.NOTE:
- Disconnect and reconnect the battery between each mirror position check.
- The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.
- If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.
- Disconnect the outer mirror actuator assembly LH connector.
*a (A) Forward position *b (B) *c (C) Driving position *d (D) *e (E) Retracted position *f Component without harness connected
(Outer Mirror Actuator Assembly LH) - For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.
OK
Battery Connection Condition Specified Condition Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Forward position (A) Moves from (A) to (E) Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Forward position (A) Does not move Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Position between forward position (A) and driving position (C) Moves from (B) to (E) Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Position between forward position (A) and driving position (C) Moves from (B) to (A) Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Driving position (C) Moves from (C) to (E) Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Driving position (C) Does not move Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Position between driving position (C) and retracted position (E) Moves from (D) to (E) Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Position between driving position (C) and retracted position (E) Moves from (D) to (C) Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Retracted position (E) Does not move Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Retracted position (E) Moves from (E) to (C) If the result is not as specified, replace the outer mirror actuator assembly LH.
- Check the operation of the mirror surface.
- INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Memory)
- Check the operation of the mirror surface.NOTE:
If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.
- Disconnect the outer rear view mirror assembly LH connector.
*a Component without harness connected
(Outer Rear View Mirror Assembly LH) - Apply battery voltage and check the operation of the mirror surface.
OK
Battery Connection Specified Condition Battery positive (+) → Terminal 1 (LMVR)
Battery negative (-) → Terminal 10 (LM+R)Turns upward Battery positive (+) → Terminal 10 (LM+R)
Battery negative (-) → Terminal 1 (LMVR)Turns downward Battery positive (+) → Terminal 9 (LMHR)
Battery negative (-) → Terminal 10 (LM+R)Turns right Battery positive (+) → Terminal 10 (LM+R)
Battery negative (-) → Terminal 9 (LMHR)Turns left If the result is not as specified, replace the outer rear view mirror assembly LH.
- Disconnect the outer rear view mirror assembly LH connector.
- Check the operation of the mirror heater.
- Disconnect the outer rear view mirror assembly LH connector.
*a Component without harness connected
(Outer Rear View Mirror Assembly LH) - Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition 4 (HTR+) - 12 (HTR-) 25°C (75°F) 3.57 to 4.83 Ω If the result is not as specified, replace the outer rear view mirror assembly LH.
- Connect a cable from the positive (+) battery terminal to terminal 4 and the negative (-) battery terminal to terminal 12, then check that the mirror becomes warm.
HINT:
It takes a short time for the mirror to become warm.
OK
Mirror becomes warm.
If the result is not as specified, replace the outer rear view mirror assembly LH.
- Disconnect the outer rear view mirror assembly LH connector.
- Check the operation of the retractable mirror.NOTE:
- Disconnect and reconnect the battery between each mirror position check.
- The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.
- If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.
- Disconnect the outer mirror actuator assembly LH connector.
*a (A) Forward position *b (B) *c (C) Driving position *d (D) *e (E) Retracted position *f Component without harness connected
(Outer Mirror Actuator Assembly LH) - For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.
OK
Battery Connection Condition Specified Condition Battery positive (+) → Terminal 3 (MR+)
Battery negative (-) → Terminal 11 (MR-)Forward position (A) Moves from (A) to (E) Battery positive (+) → Terminal 11 (MR-)
Battery negative (-) → Terminal 3 (MR+)Forward position (A) Does not move Battery positive (+) → Terminal 3 (MR+)
Battery negative (-) → Terminal 11 (MR-)Position between forward position (A) and driving position (C) Moves from (B) to (E) Battery positive (+) → Terminal 11 (MR-)
Battery negative (-) → Terminal 3 (MR+)Position between forward position (A) and driving position (C) Moves from (B) to (A) Battery positive (+) → Terminal 3 (MR+)
Battery negative (-) → Terminal 11 (MR-)Driving position (C) Moves from (C) to (E) Battery positive (+) → Terminal 11 (MR-)
Battery negative (-) → Terminal 3 (MR+)Driving position (C) Does not move Battery positive (+) → Terminal 3 (MR+)
Battery negative (-) → Terminal 11 (MR-)Position between driving position (C) and retracted position (E) Moves from (D) to (E) Battery positive (+) → Terminal 11 (MR-)
Battery negative (-) → Terminal 3 (MR+)Position between driving position (C) and retracted position (E) Moves from (D) to (C) Battery positive (+) → Terminal 3 (MR+)
Battery negative (-) → Terminal 11 (MR-)Retracted position (E) Does not move Battery positive (+) → Terminal 11 (MR-)
Battery negative (-) → Terminal 3 (MR+)Retracted position (E) Moves from (E) to (C) If the result is not as specified, replace the outer mirror actuator assembly LH.
- Check the operation of the mirror surface.