Warning Notification Function Malfunction [09/2017 - ]: Procedure

1. Check the problem symptom.
   1. Check the problem symptom of the warning notification function.

      Result

      Result	Proceed to
      The accessory meter assembly screen does not show a warning message even though a warning light turns on or the multi-information display indicates a warning.	A
      The accessory meter assembly screen shows a warning message even though a warning light is not on and the multi-information display does not indicate a warning.	B
      The accessory meter assembly screen shows a warning message different from the warning light or the multi-information display.

      HINT: 

      • The warning notification function sends information to the service center through communication.
      • Carefully confirm the conditions that caused the malfunction in order to determine if a temporary problem with the radio wave signal conditions caused the malfunction.

Result: 

B 

See step  6

Result: 

A 

See step  2

1. Check if the indicated warning light or message is listed in the following table.

   HINT: 

   Only messages listed in the table are included in the warning notification function.

   Warning Name
   Engine warning
   Brake system warning
   VSC warning
   ABS warning
   Dynamic Rear Steering warning
   EPS warning
   VGRS warning
   Charging system warning
   Airbag warning
   PCS warning
   Cruise warning
   Intuitive parking assist system open circuit warning
   Brake override system warning
   Smart access system with push-button start warning
   AFS warning
   Automatic headlight beam level control system warning
   Automatic high beam warning
   LED headlight warning
   4WD warning
   Tire pressure system warning
   Electric parking brake warning
   Auto hold warning
   BSM system warning
   Lane departure alert system warning
   Engine oil level warning
   Brake fluid level warning
   Engine oil pressure warning
   Tire pressure low warning
   Washer fluid level warning
   Engine oil maintenance warning
   High coolant temperature warning
   Maintenance advice warning

   Result

   Result	Proceed to
   Warning light or message is listed in the table.	A
   Warning light or message is not listed in the table.	B

Result: 

B 

END 

Result: 

A 

See step  3

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Bus Check.
5. Check that all ECUs and sensors that use CAN communication are connected.

   Refer to DIAGNOSIS SYSTEM [09/2017 - 09/2018] , or refer to DIAGNOSIS SYSTEM [09/2018 - ]

   Result

   Result	Proceed to
   There are no connection problems.	A
   There is a connection problem.	B

Result: 

B 

GO TO CAN COMMUNICATION SYSTEM 

(Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2015 - ] )

Result: 

A 

See step  4

1. Check that the warning light of the combination meter assembly illuminates and a message displays on the multi-information display when there is a malfunction, and do not when there is not a malfunction.

   OK

   There are no problems with warning lights or warning messages.

   HINT: 

   The warning notification function of the telematics system uses the warning notification signals sent and received by the meter/gauge system. Therefore, if the meter/gauge system is not operating normally, the warning notification function will not operate normally.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

GO TO METER / GAUGE SYSTEM 

(Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] )

Result: 

OK 

See step  5

1. Check if the navigation system is operating and functioning normally.

   OK

   The navigation system is normal.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY. Refer to  REMOVAL [09/2017 - ] 

Result: 

NG 

GO TO NAVIGATION SYSTEM 

(Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] )

1. Check that the warning light of the combination meter assembly illuminates and a message displays on the multi-information display when there is a malfunction, and do not when there is not a malfunction.

   OK

   There are no problems with warning lights or warning messages.

   HINT: 

   The warning notification function of the telematics system uses the warning notification signals sent and received by the meter/gauge system. Therefore, if the meter/gauge system is not operating normally, the warning notification function will not operate normally.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY. Refer to  REMOVAL [09/2017 - ] 

Result: 

NG 

GO TO METER / GAUGE SYSTEM 

(Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] )