Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Lexus >> 2013 >> RX 350 Base, AWD >> Repair and Diagnosis >> General Information >> Towing >> Introduction (General Information) >> Repair Instruction >> Initialization [03/2012 - 07/2012] >> Initialization [03/2012 - 07/2012]

Initialization [03/2012 - 07/2012]

  1. PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED/RECONNECTED 
    Necessary Procedures Effect / Inoperative Function When Necessary Procedures are not Performed Refer to
    Reset back door close position
    • Power back door function
    • Back door closer function
    		 Refer to INITIALIZATION [03/2012 - ]
    Correct the steering angle neutral point Parking assist monitor system Refer to INITIALIZATION [03/2012 - ]
    NOTE:

    After the engine switch is turned off, the multi-media module receiver assembly (w/ Navigation System or w/ Parking Assist Monitor System) records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

  2. PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED 
    Replacement Part Necessary Procedure Effect / Inoperative Function when Necessary Procedures are not Performed Refer to
    ECM Vehicle Identification Number (VIN) registration MIL comes on Refer to REGISTRATION [03/2012 - ]
    ECU communication ID registration (Engine immobiliser system) Engine start Refer to REGISTRATION [03/2012 - ]
    Millimeter wave radar sensor assembly Adjust millimeter wave radar sensor assembly (Dynamic radar cruise control system)
    • Dynamic radar cruise control system
    • Pre-collision system
    		 Refer to ADJUSTMENT [03/2012 - ]
    Automatic transaxle assembly
    1. Reset memory
    2. Input transaxle compensation code into TCM
    3. Perform road test to allow TCM to Learn
    • Large shift shock
    • The deterioration of fuel efficiency
    		 Refer to INITIALIZATION [03/2012 - ] for U660E Initialization
    Refer to REGISTRATION [03/2012 - ] for U660E Registration
    Refer to INITIALIZATION [03/2012 - ] for U660F Initialization
    Refer to REGISTRATION [03/2012 - ] for U660F Registration
    • Valve body assembly
    • Shift solenoid valve SL3 and/or SL4
    1. Reset memory
    2. Reset transaxle compensation code
    3. Perform road test to allow TCM to learn
    • Large shift shock
    • The deterioration of fuel efficiency
    Shift solenoid valve SL1 and/or SL2 Perform road test to allow TCM to learn
    • Large shift shock
    • The deterioration of fuel efficiency
    TCM (If possible, read the transaxle compensation code from the previous TCM) Possible
    1. Reset memory
    2. Transfer transaxle compensation code
    3. Perform road test to allow TCM to learn
    • Large shift shock
    • The deterioration of fuel efficiency
    Impossible
    1. Reset memory
    2. Reset transaxle compensation code
    3. Perform road test to allow TCM to learn
    • Large shift shock
    • The deterioration of fuel efficiency
    • Tire pressure warning ECU
    • Tire pressure warning valve and transmitter
    		 Code registration (Tire pressure warning system)
    • When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates.
    • Tire pressure warning function
    		 Refer to REGISTRATION [03/2012 - ]
    Brake actuator assembly (Skid control ECU) Perform yaw rate and acceleration sensor zero point calibration and store system information
    • ABS warning light illumination
    • Slip indicator light illumination
    • VSC disabled or malfunctioning
    		 Refer to CALIBRATION [03/2012 - ]
    Yaw rate and acceleration sensor
    • Clear the zero point calibration data and system information
    • Perform yaw rate and acceleration sensor zero point calibration and store system information
    Power steering ECU Rotation angle sensor initialization and torque sensor zero point calibration
    • P/S warning light comes on
    • EPS control
    		 Refer to CALIBRATION [03/2012 - ]
    Steering column assembly Rotation angle sensor initialization and torque sensor zero point calibration Steering effort is different between turning steering wheel to left and right
    Spiral with sensor cable sub-assembly
    • Correct steering angle neutral point
    • Steering angle setting
    		 Parking assist monitor system Refer to INITIALIZATION [03/2012 - ] for Initialization
    Refer to CALIBRATION [03/2012 - ] for Calibration
    Multi-media module receiver assembly Parking assist monitor system initialization Parking assist monitor system Refer to CALIBRATION [03/2012 - ]
    Rear television camera assembly Back camera position setting Parking assist monitor system
    Inner rear view mirror assembly*1 Re-registration of codes in the garage door opener system
    • Register transmitter code
    		 Garage door opener system Refer to REGISTRATION [03/2012 - ]
    DCM (Telematics Transceiver) DCM activation Safety connect system Refer to DCM ACTIVATION [03/2012 - ]
    • Certification ECU (smart key ECU assembly)
    • ID code box (immobiliser code ECU)
    • Steering lock ECU (steering lock actuator assembly)
    • Key
    		 Code registration (Engine immobiliser system)
    • Wireless door lock control system
    • Smart access system with push-button start
    • Engine start
    		 Refer to REGISTRATION [03/2012 - ]
    Remote engine starter ECU assembly *2 Code registration (Engine immobiliser system) Remote engine start
    • Occupant classification ECU
    • Front passenger seat
    1. Zero point calibration (Occupant classification system)
    2. Sensitivity check (Occupant classification system)
    • Occupant classification system
    • Passenger airbag ON/OFF indicator
    • Airbag system (Front passenger side)
    • Seat belt warning system (Front passenger side)
    		 Refer to INITIALIZATION [03/2012 - ]
    • Power window regulator motor
    • Door window regulator
    		 Initialize power window control system
    • Automatic door glass open/ close function
    • Jam protection function
    • Operation function after engine switch is turned off
    • Key-linked operation function
    • Wireless transmitter-linked operation
    		 Refer to INITIALIZATION [03/2012 - ]
    • Sliding roof ECU (sliding roof drive gear sub-assembly)
    • Sliding roof glass
    • Sliding roof housing
    		 Initialize sliding roof ECU (pulse sensor initial position setting)
    • Automatic slide open/close and tilt up/down function of sliding roof
    • Jam protection function
    • Operation function after engine switch is turned off
    • Key-linked operation function
    • Wireless transmitter-linked operation
    		 Refer to INITIALIZATION [03/2012 - ]
    AFS ECU (headlight swivel ECU assembly) Perform AFS ECU (headlight swivel ECU assembly) initialization Headlight leveling function Refer to INITIALIZATION [03/2012 - 07/2012]
    Rear height control sensor sub-assembly RH Perform AFS ECU (headlight swivel ECU assembly) initialization Headlight leveling function
    • *1: w/ Garage Door Opener System
    • *2: w/ Remote Engine Starter System
scientia non olet · About Mike's Workshop Manuals