Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Lexus >> 2012 >> IS F >> Repair and Diagnosis >> Accessories & Equipment >> Warning Systems >> Intuitive Parking Assist System (Diagnostics - Introduction) >> Intuitive Parking Assist System >> Data List / Active Test >> Data List / Active Test

Data List / Active Test

  1. Data List 

    Use the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Intuitive P/A / Data List.
    5. Check the value(s) by referring to the table below.
      INTUITIVE P/A

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Main Switch Clearance sonar main switch / OFF or ON OFF: Clearance sonar main switch OFF
      ON: Clearance sonar main switch ON      		 -
      Fr Left Sensor Front left sensor information / Undtct, Long, Middle, Close, Freeze, Open or Blink Undtct: Not detected
      Long: Detected (long-range)
      Middle: Detected (medium-range)
      Close: Detected (close-range)
      Freeze: Freeze (Sensor is frozen)
      Open: Open (Open in sensor)
      Blink: Blink (All displays blinking)      		 -
      Fr Right Sensor Front right sensor information / Undtct, Long, Middle, Close, Freeze, Open or Blink Undtct: Not detected
      Long: Detected (long-range)
      Middle: Detected (medium-range)
      Close: Detected (close-range)
      Freeze: Freeze (Sensor is frozen)
      Open: Open (Open in sensor)
      Blink: Blink (All displays blinking)      		 -
      Rr Left Sensor Rear left sensor information / Undtct, Long, Middle, Close, Freeze, Open or Blink Undtct: Not detected
      Long: Detected (long-range)
      Middle: Detected (medium-range)
      Close: Detected (close-range)
      Freeze: Freeze (Sensor is frozen)
      Open: Open (Open in sensor)
      Blink: Blink (All displays blinking)      		 -
      Rr Left Center Sensor Rear left center sensor information / Undtct, Long, M Long, Middle, Close, Freeze, Open or Blink Undtct: Not detected
      Long: Detected (long-range)
      M Long: Detected (mid long-range)
      Middle: Detected (medium-range)
      Close: Detected (close-range)
      Freeze: Freeze (Sensor is frozen)
      Open: Open (Open in sensor)
      Blink: Blink (All displays blinking)      		 -
      Rr Right Center Sensor Rear right center sensor information / Undtct, Long, M Long, Middle, Close, Freeze, Open or Blink Undtct: Not detected
      Long: Detected (long-range)
      M Long: Detected (mid long-range)
      Middle: Detected (medium-range)
      Close: Detected (close-range)
      Freeze: Freeze (Sensor is frozen)
      Open: Open (Open in sensor)
      Blink: Blink (All displays blinking)      		 -
      Rr Right Sensor Rear right sensor information / Undtct, Long, Middle, Close, Freeze, Open or Blink Undtct: Not detected
      Long: Detected (long-range)
      Middle: Detected (medium-range)
      Close: Detected (close-range)
      Freeze: Freeze (Sensor is frozen)
      Open: Open (Open in sensor)
      Blink: Blink (All displays blinking)      		 -
      Rr Buzzer Onset Range Rear buzzer onset range / Narrow or Wide Narrow: 600 mm (23.62 in.)
      Wide: 1500 mm (59.06 in.)      		 Buzzer activation range can be customized
      Keep Sense Buzzer Keep sense status buzzer / Not Avail or Avail Not Avail: Buzzer sound stops in 3 sec.
      Avail: Buzzer sound does not stop      		 Buzzer can be stopped when an obstacle is at the same position for 3 sec. or more
      Fr & Rr Buzzer Volume Front & rear buzzer volume / L, M1, M2, M3, or H L: Low volume
      M1: Medium low volume
      M2: Medium volume
      M3: Medium high volume
      H: High volume      		 Buzzer volume can be customized
      Non P/R Range Sensor Non P/R range sensor / All, F, Rcrn2 or F All: All sensors are available
      F, Rcrn 2: Corner sensors are available
      F: Front sensors are available      		 Sensors in positions other than P and R can be customized
  2. Active Test 

    Use the Techstream to perform Active Tests allows the relay, actuator, and other items to operate without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.

    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Intuitive P/A / Active Test.
    5. Check the operation by referring to the table below.
      INTUITIVE P/A

      Tester Display Test Part Control Range Diagnostic Note
      Rear Buzzer Rear buzzer (Clearance warning buzzer) STOP or OPERATE -
scientia non olet · About Mike's Workshop Manuals