Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Lexus >> 2011 >> IS F >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System (Diagnostic Codes (P0010-P014F) >> SFI System >> DTC P0102: Mass Air Flow Circuit Low; DTC P0103: Mass Air Flow Circuit High >> Procedure

DTC P0102: Mass Air Flow Circuit Low; DTC P0103: Mass Air Flow Circuit High: Procedure

  1. READ DTC OUTPUT 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine / Trouble Codes.
    5. Read the DTCs.

      Result

      Result Proceed to
      DTC P0102 is output A
      DTC P0103 is output B

    B → See step   5 

    A: Go to next step 

  2. INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE) 
    1. Disconnect the mass air flow meter connector.
      Fig 1: Identifying Mass Air Flow Meter Connector E29
      GTY147475Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Turn the engine switch on (IG).
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      E29-3 (+B) - Body ground Engine switch on (IG) 11 to 14 V
    4. Reconnect the mass air flow meter connector.

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - EFI MAIN RELAY) 

    OK: Go to next step 

  3. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) 
    1. Disconnect the mass air flow meter connector.
    2. Disconnect the ECM connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)

      Tester Connection Condition Specified Condition
      E29-5 (VG) - E3-25 (VG) Always Below 1 Ω
      E29-4 (E2G) - E3-24 (E2G) Always Below 1 Ω

      Standard Resistance (Check for Short)

      Tester Connection Condition Specified Condition
      E29-5 (VG) or E3-25 (VG) - Body ground Always 10 kΩ or higher
    4. Reconnect the mass air flow meter connector.
    5. Reconnect the ECM connector.

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  4. INSPECT MASS AIR FLOW METER 
    1. Perform On-vehicle Inspection. Refer to ON-VEHICLE INSPECTION .
    2. Perform Inspection. Refer to INSPECTION .
    3. Inspect the function of the mass air flow meter.
      1. Connect the Techstream to the DLC3.
      2. Turn the engine switch on (IG).
      3. Turn the Techstream on.
      4. Enter the following menus: Powertrain / Engine / Data List / MAF.
      5. Start the engine.
      6. Check that the reading of the mass air flow meter changes when the engine is raced.

        OK

        The reading changes.

    NG → See step   8 

    OK → See step   7 

  5. INSPECT MASS AIR FLOW METER (SENSOR GROUND) 
    1. Disconnect the mass air flow meter connector.
      Fig 2: Identifying Mass Air Flow Meter Connector
      GTY262709Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      E29-4 (E2G) - Body ground Always Below 1 Ω
    3. Reconnect the mass air flow meter connector.

    NG → See step   6 

    OK → See step   8 

  6. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) 
    1. Disconnect the mass air flow meter connector.
    2. Disconnect the ECM connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)

      Tester Connection Condition Specified Condition
      E29-4 (E2G) - E3-24 (E2G) Always Below 1 Ω
    4. Reconnect the mass air flow meter connector.
    5. Reconnect the ECM connector.

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK → See step   7 

  7. REPLACE ECM. Refer to  REMOVAL 
  8. REPLACE MASS AIR FLOW METER. Refer to  REMOVAL