Initialization Of VGRS System During PDS (L-SB-0111-08)
Publication date: 2008-09-11Reference number: L-SB-0111-08
INITIALIZATION OF VGRS SYSTEM DURING PDS
TECHNICAL SERVICE BULLETIN
Reference Number(s): L-SB-0111-08, Date of Issue:
September 11, 2008
| LEXUS: | 2009 LS600H |
| Section: | Pre-Delivery Service |
| Service Category: | General |
| COPYRIGHT: | © 2018 Lexus, a division of Toyota Motor Sales, USA License Agreement TMS1002 |
Applicability
APPLICABILITY REFERENCE
| YEAR(S) | MODEL(S) | ADDITIONAL INFORMATION |
|---|---|---|
| 2009 | LS600H |
Introduction
This bulletin describes the initialization procedure for the Variable Gear Ratio Steering (VGRS) system.
The DCC fuses are removed at the assembly plant to reduce parasitic current draw from the battery during transport and storage. As a result of the removal of the DCC fuses, the VGRS system will be inoperative and the steering wheel may be off-center. After the DCC fuses have been reinstalled, the VGRS system will be operative, but the steering wheel may become off-center by 5 - 10 degrees. This condition may also appear when the battery terminal has been disconnected. Initialize the VGRS system following the procedure in this bulletin after installing the DCC fuses or when reconnecting the battery terminal.
NOTE:
Do NOT adjust the steering wheel centering (i.e., do NOT adjust tie rod ends) before initialization of the VGRS system, or the steering may be off-center on the opposite side after initialization.
Required Tools & Equipment
REQUIRED TOOLS & EQUIPMENT
| REQUIRED EQUIPMENT | SUPPLIER | PART NUMBER | QTY | ||
|---|---|---|---|---|---|
| TIS Techstream(1)
NOTE:
Software version 3.01.000 or later is required.
|
ADE | TSPKG1 | 1 | ||
|
|||||
NOTE:
Additional TIS Techstream units may be ordered by calling Approved Dealer Equipment (ADE) at 1-800-368-6787.
Warranty Information
WARRANTY INFORMATION
| OP CODE | DESCRIPTION | TIME | OFP | T1 | T2 |
|---|---|---|---|---|---|
| N/A | Not Applicable to Warranty | - | - | - | - |
Initialization Procedure
- Drive the vehicle on a straight road at 22 mph (35 km/h) or more for at least 5 seconds. At this point, the steering wheel will still remain off-center by 5 - 10 degrees.NOTE: In this step, the neutral position of the steering wheel is recorded in the VGRS ECU memory.
- Perform normal cornering 2 - 3 times. The steering wheel position is automatically corrected in this step.
- With the vehicle at a standstill, turn the steering wheel from lock to lock, then drive straight again, and the steering wheel should be centered.
- Confirm the steering wheel is centered.
- If the steering wheel is centered, initialization is complete. Go to step 5.
- If the steering wheel is off-center, go to step 1.
- Confirm initialization has been completed.
- Access the VGRS Data List using TIS Techstream.
- Confirm the "STRAIGH ANG FLG" parameter reads "VALID."
NOTE: Prior to initialization, the "STRAIGH ANG FLG" parameter will read "INVALID." When the VGRS initialization procedure is complete, the "STRAIGH ANG FLG" parameter will change to "VALID."- If "VALID" and steering is off-center, refer to the Technical Information System (TIS), 2009 model year LS 600h Repair Manual, Steering - Steering Column - "Steering Column: Variable Gear Ratio Steering System: Calibration" and "Steering Column: Variable Gear Ratio Steering System: Test Mode Procedure".
- If "INVALID," return to step 1 and perform driving procedure again.
- If "INVALID" returns again, check for VGRS system DTCs and diagnose the condition following the procedures found in the Repair Manual.