Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Lexus >> 2009 >> LS 600hL >> Repair and Diagnosis >> External Pages >> Different car >> Section 27 (Engine Immobilizer) >> Engine Immobilizer System >> Data List / Active Test

Data List / Active Test

WARNING: This page is about a different car, the 2008 Lexus LS 600hL. However, it is still accessible from the selected car via links, so may be relevant.
  1. DATA LIST 

    HINT

    Using the intelligent tester or Techstream to read the DATA LIST allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the DATA LIST information early in troubleshooting is one way to save diagnostic time

    NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
    1. Connect the intelligent tester or Techstream to the DLC3
    2. Turn the power switch ON (IG)
    3. Turn the tester on.
    4. Enter the following menus:
      1. Intelligent tester - Select. DIAGNOSIS / OBD/ MOBD / BODY SYSTEM / SMART ACCESS / DATA LIST.
      2. Techstream - Select Body Electrical / Smart Access / Data List.
    5. According to the display on tester, read the "DATA LIST" or "Data List".
      1. Intelligent tester

        SMART ACCESS: 

        SMART ACCESS REFERENCE CHART

        Tester Display Measurement Item/Range Normal Condition
        IG SW Power switch ON (IG) signal/ON or OFF ON Power switch ON (ACC, IG)
        OFF Power switch OFF or ON (ACC)
        IMMOBILIZER Engine immobilizer system status/SET or UNSET SET Key is not in cabin
        UNSET Key is in cabin
        MASTER KEY Master key code signal/MATCH or NO MATCH MATCH Master key code is sent
        NO MATCH Unmatched master key code is sent
        ENCRYPT CODE Transponder chip signal/OK or NG OK Correct data sent
        NG Incorrect data sent
        SERIAL NUMBER Transponder chip signal/OK or NG OK Correct data sent
        NG Incorrect data sent
        FRAME Transponder chip signal/OK or NG OK Correct data sent
        NG Incorrect data sent
        RESPONSE Transponder chip signal/OK or NG OK Correct data sent
        NG Incorrect data sent
        BCC Transponder chip signal/OK or NG OK Correct data sent
        NG Incorrect data sent
        STATUS Transponder chip data/OK or NG OK Data OK
        NG Data error
        IDBX SLEEP COND ID code box condition/YES or NO YES ID code box in sleep condition
        NO ID code box not in sleep condition
        IDBX START COND ID code box condition/YES or NO YES ID code box sends wake up signal
        NO ID code box does not send wake up signal
        EFI CODE RECEIVE SFI code receive (when DTC detected)/OK or NG OK SFI code is received
        NG SFI code is not received
        S CODE CHK S code verification result/OK or NG OK Verification is confirmed
        NG Verification is not confirmed
        L CODE CHK L code verification result/OK or NG OK Verification is confirmed
        NG Verification is not confirmed
        LCK RQ RECEIVE Steering unlock command reception status/OK or NG OK Steering unlock request is received
        NG Steering unlock request is not received
        UNLOCK RQ RECEIVE Steering lock command reception status/OK or NG OK Steering lock request is received
        NG Steering lock request is not received
        EFI COM SFI communication/OK or NG OK SFI communication is normal
        NG SFI communication is abnormal
        START RQST ID code box start request condition/OK or NG OK Start request condition signal is received (past)
        NG Start request condition signal is not received (past)
        S CODE CHK-PAST S code verification result (past)/ OK or NG OK Verification is confirmed (past)
        NG Verification is not confirmed (past)
        L CODE CHK-PAST L code verification result (past)/ OK or NG OK Verification is confirmed (past)
        NG Verification is not confirmed (past)
      2. Techstream

        Smart Access: 

        SMART ACCESS REFERENCE CHART

        Tester Display Measurement Item/Range Normal Condition
        Ignition Switch Power switch ON (IG) signal/ON or OFF ON Power switch ON (ACC, IG)
        OFF Power switch OFF or ON (ACC)
        Immobilizer Engine immobilizer system status/Set or Unset Set Key is not in cabin
        Unset Key is in cabin
        Master Key Master key code signal/Match or No Match Match Master key code is sent
        No Match Unmatched master key code is sent
        Different Encrypt Code Transponder chip signal/OK or NG OK Correct data sent
        NG Incorrect data sent
        Different Serial Number Transponder chip signal/OK or NG OK Correct data sent
        NG Incorrect data sent
        Frame Error Transponder chip signal/OK or NG OK Correct data sent
        NG Incorrect data sent
        Response Transponder chip signal/OK or NG OK Correct data sent
        NG Incorrect data sent
        BCC Malfunction Transponder chip signal/OK or NG OK Correct data sent
        NG Incorrect data sent
        Abnormal Status Transponder chip data/OK or NG OK Data OK
        NG Data error
        ID-BOX Sleep Condition ID code box condition/Yes or No Yes ID code box in sleep condition
        No ID code box not in sleep condition
        ID-BOX Start Condition ID code box condition/Yes or No YES ID code box sends wake up signal
        NO ID code box does not send wake up signal
        EFI Code Receive SFI code receive (when DTC detected)/OK or NG OK SFI code is received
        NG SFI code is not received
        S Code Check S code verification result/OK or NG OK Verification is confirmed
        NG Verification is not confirmed
        L Code Check L code verification result/OK or NG OK Verification is confirmed
        NG Verification is not confirmed
        Unlock Request Receive Steering unlock command reception status/OK or NG OK Steering unlock request is received
        NG Steering unlock request is not received
        Lock Request Receive Steering lock command reception status/OK or NG OK Steering lock request is received
        NG Steering lock request is not received
        EFI Communication SFI communication/OK or NG OK SFI communication is normal
        NG SFI communication is abnormal
        Engine Start Request ID code box start request condition/OK or NG OK Start request condition signal is received (past)
        NG Start request condition signal is not received (past)
        S Code Check (Past) S code verification result (past)/ OK or NG OK Verification is confirmed (past)
        NG Verification is not confirmed (past)
        L Code Check (Past) L code verification result (past)/ OK or NG OK Verification is confirmed (past)
        NG Verification is not confirmed (past)
  2. ACTIVE TEST 

    HINT

    Using the intelligent tester or Techstream to perform ACTIVE TEST allows relays, VSVs, actuators and other items to be operated without removing any parts This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed Performing ACTIVE TEST early in troubleshooting is one way to save diagnostic time DATA LIST information can be displayed while performing ACTIVE TEST

    1. Connect the intelligent tester or Techstream to the DLC3.
    2. Turn the power switch ON (IG).
    3. Turn the tester on.
    4. Enter the following menus:
      1. Intelligent tester - Select. DIAGNOSIS / OBD/ MOBD / BODY SYSTEM / SMART ACCESS / ACTIVE TEST.
      2. Techstream - Select. Body Electrical / Smart Access / Active Test
    5. According to the display on tester, perform the "ACTIVE TEST" or "Active Test".
      1. Intelligent tester

        SMART ACCESS: 

        SMART ACCESS REFERENCE CHART

        Tester Display Test Part Control Range Diagnostic Note
        SECURITY INDIC Security indicator light (for driver side and front passenger side) ON or OFF -
      2. Techstream

        Smart Access: 

        SMART ACCESS REFERENCE CHART

        Tester Display Test Part Control Range Diagnostic Note
        Security Indicator Security indicator light (for driver side and front passenger side) ON or OFF -
scientia non olet · About Mike's Workshop Manuals