Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Lexus >> 2007 >> RX 400h AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 43 (Windshield / WINDOWGLASS) >> Power Window Regulator Motor >> Inspection

Power Window Regulator Motor: Inspection

WARNING: This page is about a different car, the 2006 Lexus RX 400h. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSPECT POWER WINDOW REGULATOR MOTOR (FRONT RH) 
    1. Remove the power window regulator motor.
    2. Apply battery voltage to the motor connector according to the table below.
      NOTE: Do not apply battery to any terminals except terminals 1 and 2.

      Standard 

      POWER WINDOW REGULATOR MOTOR (FRONT RH)

      Measurement Condition Specified Condition
      Battery positive (+) -> Terminal 1 (D)
      Battery negative (-) -> Terminal 2 (U)      		 Motor gear rotates clockwise
      Battery positive (+) -> Terminal 2 (U)
      Battery negative (-) -> Terminal 1 (D)      		 Motor gear rotates counterclockwise
      Fig 1: Identifying Power Window Regulator Motor Connector Terminals
      G04116036Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSPECT POWER WINDOW REGULATOR MOTOR (FRONT LH) 
    1. Remove the power window regulator motor.
    2. Apply battery voltage to the motor connector according to the table below.
      NOTE: Do not apply battery to any terminals except terminals 1 and 2.

      Standard 

      POWER WINDOW REGULATOR MOTOR (FRONT LH)

      Measurement Condition Specified Condition
      Battery positive (+) -> Terminal 1 (D)
      Battery negative (-) -> Terminal 2 (U)      		 Motor gear rotates counterclockwise
      Battery positive (+) -> Terminal 2 (U)
      Battery negative (-) -> Terminal 1 (D)      		 Motor gear rotates clockwise
      Fig 2: Identifying Power Window Regulator Motor Connector Terminals
      G04116033Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSPECT POWER WINDOW REGULATOR MOTOR (REAR RH) 
    1. Remove the power window regulator motor.
    2. Apply battery voltage to the motor connector according to the table below.
      NOTE: Do not apply battery to any terminals except terminals 1 and 2.

      Standard 

      POWER WINDOW REGULATOR MOTOR (REAR RH)

      Measurement Condition Specified Condition
      Battery positive (+) -> Terminal 1 (D)
      Battery negative (-) - Terminal 2 (U)      		 Motor gear rotates clockwise
      Battery positive (+) -> Terminal 2 (U)
      Battery negative (-) -> Terminal 1 (D)      		 Motor gear rotates counterclockwise
      Fig 3: Identifying Power Window Regulator Motor Connector Terminals
      G04116036Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSPECT POWER WINDOW REGULATOR MOTOR (REAR LH) 
    1. Remove the power window regulator motor.
    2. Apply battery voltage to the motor connector according to the table below.
      NOTE: Do not apply battery to any terminals except terminals 1 and 2.

      Standard 

      POWER WINDOW REGULATOR MOTOR (REAR LH)

      Measurement Condition Specified Condition
      Battery positive (+) -> Terminal 1 (D)
      Battery negative (-) -> Terminal 2 (U)      		 Motor gear rotates counterclockwise
      Battery positive (+) -> Terminal 2 (U)
      Battery negative (-) -> Terminal 1 (D)      		 Motor gear rotates clockwise
      Fig 4: Identifying Power Window Regulator Motor Connector Terminals
      G04116033Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About Mike's Workshop Manuals