Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Lexus >> 2004 >> RX 330 AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 533 (Supplemental Restraint System) >> Center Airbag Sensor Assembly >> Installation

Center Airbag Sensor Assembly: Installation

WARNING: This page is about a different car, the 2007 Lexus RX 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL CENTER AIRBAG SENSOR ASSEMBLY 
    1. Check that the ignition switch is off.
      Fig 1: Identifying Center Airbag Sensor Assembly Bolts
      G05270424Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Check that the battery negative (-) terminal is disconnected.
      CAUTION: After disconnecting the negative battery terminal, wait for at least 90 seconds before starting the operation.
    3. Temporarily install the center airbag sensor assembly with the 3 bolts.
      NOTE:
      • If the center airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
      • When installing the center airbag sensor assembly, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
        Fig 2: Installing Center Airbag Sensor Assembly With 3 Bolts
        G05270425Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Tighten the 3 bolts to the specified torque.

      Torque: 17.5 N*m (179 kgf*cm, 13 ft.*lbf) 

    5. Check that there is no looseness in the installation parts of the center airbag sensor assembly.
    6. Connect the 3 connectors to the center airbag sensor assembly.
    7. Check that the water-proof sheet is properly set.
  2. INSTALL AIR DUCT REAR NO.1 
  3. INSTALL AIR DUCT REAR NO.2 
  4. INSTALL CONSOLE COVER LOWER 
    1. Connect the connector to the console cover lower.
    2. Install the console cover lower with the 2 screws.
  5. INSTALL CONSOLE BOX NO.1 DUCT 
  6. INSTALL REAR CONSOLE BOX  (See INSTALLATION )
  7. INSTALL CONSOLE BOX HOLE COVER  (See INSTALLATION )
  8. INSTALL CONSOLE BOX NO.2 HOLE COVER 
    Fig 3: Identifying Console Cover Lower With Screws
    G05270426Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    HINT:

    Use the same procedures for the console box No.2 hole cover and the console box hole cover.

  9. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER  (See INSTALLATION )
  10. INSTALL FLOOR CARPET COVER CENTER LH  (See INSTALLATION )
  11. INSTALL FLOOR CARPET COVER CENTER RH 

    HINT:

    Use the same procedures for the floor carpet cover center RH and the floor carpet cover center LH.

  12. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY  (See INSTALLATION )
  13. INSTALL INSTRUMENT PANEL NO.2 UNDER COVER SUB-ASSEMBLY  (See INSTALLATION )
  14. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH 

    HINT:

    Use the same procedures for the cowl side trim sub-assembly RH and the cowl side trim sub-assembly LH (See INSTALLATION ).

  15. INSTALL FRONT DOOR OPENING TRIM RH WEATHERSTRIP 
  16. INSTALL FRONT DOOR SCUFF LH PLATE 
  17. INSTALL INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LOWER  (See INSTALLATION )
  18. INSTALL FRONT DOOR SCUFF RH PLATE 

    HINT:

    Use the same procedures for the front door scuff RH plate and the front door scuff LH plate.

  19. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER  (See INSTALLATION )
  20. INSTALL CONSOLE PANEL UPPER FRONT  (See INSTALLATION )
  21. INSTALL FRONT SEAT ASSEMBLY  (See INSTALLATION )
  22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
  23. PERFORM INITIALIZATION 
    1. Perform initialization (See INITIALIZATION ).

      HINT:

      Some systems need initialization after reconnecting the cable to the negative battery terminal.

  24. INSPECT CHECK POWER SEAT FUNCTION 
  25. INSPECT SEAT HEATER OPERATION 
  26. INSPECT SRS WARNING LIGHT 
    1. Inspect the SRS warning light (See DIAGNOSIS SYSTEM  ).
scientia non olet · About Mike's Workshop Manuals