Common Specs & Procedures
CARNIVAL COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SERVICE DATA | ||
| Torque | TIGHTENING TORQUE | ||
| Axle Nut/Hub Nut | |||
| Front | 217-231 ft. lbs. (294.2-313.8 N.m) | ||
| Rear | NA | ||
| Battery | See BATTERY | ||
| Brakes | |||
| Bleeding Sequence | See Bleeding Of Brake System under BRAKE BLEEDING PROCEDURES . | ||
| Disc Brakes | Refer to SPECIFICATIONS . | ||
| Drum Brakes | N/A | ||
| Torque | Refer to TIGHTENING TORQUE . | ||
| Charging | |||
| Generator | Refer to Alternator Specification under ALTERNATOR . | ||
| Torque | Refer to TIGHTENING TORQUE . | ||
| Drive Belts | |||
| Adjustment | N/A | ||
| Belt Routing | Refer to Drive Belt Routing figure under REMOVAL & INSTALLATION . | ||
| Engine Cooling | |||
| General Service Specifications | See Cooling System in table under SPECIFICATIONS . | ||
| Capacity | Approx. 9.0 U.S. Qts. (8.6L) | ||
| Radiator Cap Pressure | |||
| Main Valve Opening Pressure | 13.51-17.78 psi (93.16-122.58 kPa) | ||
| Thermostat R & I | INTEGRATED THERMAL MANAGEMENT MODULE (ITM) | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | COMPRESSION TEST | ||
| Oil pressure | At idle and with oil temperature 230°F (110°C), normal oil pressure should be at least 12.8 psi (0.9 kg/cm2 ) or 88.6 kPa. | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUE | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| Flexplate-To-Crankshaft Bolt | 86.8-94.0 ft. lbs. (117.7-127.5 N.m) | ||
| Fuel System | |||
| Fuel Filter Location | Fuel filter is part of fuel pump. | ||
| Low Pressure Fuel Line Specification | 480 - 520 kPa (4.9-5.3 kgf/cm2 , 69.7 - 75.4 psi) | ||
| High Pressure Fuel Line Specification | 2.0-25 MPa (20.4-254.9 kgf/cm2 ) | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST | ||
| Fuel Pressure Release Procedure | RELEASE RESIDUAL PRESSURE IN FUEL LINE | ||
| Fuel Filter R & I | Fuel filter is part of fuel pump. Refer to FUEL FILTER for removal and installation. | ||
| Ignition | |||
| Firing Order & Cylinder Identification | 1-2-3-4-5-6: Also refer to FIRING ORDER & CYLINDER IDENTIFICATION article. | ||
| Ignition Wires (Resistance) | Coil On Plug N/A | ||
| Ignition Wires (Routing) | N/A | ||
| Spark Plug | Refer to SPARK PLUG | ||
| Starting | |||
| Starter | Refer to STARTER | ||
| Torque | Refer to TIGHTENING TORQUE . | ||
| Wheel Alignment | |||
| Adjustment Specifications | Refer to WHEEL ALIGNMENT . | ||
| Torque | Refer to TIGHTENING TORQUE | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 79.6 ~ 94.0 ft. lbs. (107.9 ~ 127.5 N.m) | ||