Common Specs & Procedures
SORENTO COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUES | ||
| Axle Nut/Hub Nut | |||
| Front | 294.2-313.8 N.m (30.0-32.0 kgf/cm2 , 217.0-231.5 lb. ft.) | ||
| Rear | 294.2-313.8 N.m (30.0-32.0 kgf/cm2 , 217.0-231.5 lb. ft.) | ||
| Battery | |||
| 2.4L | BATTERY | ||
| 3.3L | BATTERY . | ||
| Brakes | |||
| Bleeding Sequence | Refer to ESP BLEEDING OF BRAKE SYSTEM . | ||
| Disc Brakes | |||
| Service Specifications | SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUES . | ||
| Drum Brakes | |||
| Service Specifications | N/A | ||
| Torque | N/A | ||
| Charging | |||
| Generator | |||
| 2.4L | ALTERNATOR | ||
| 3.3L | ALTERNATOR | ||
| Torque | |||
| 2.4L | Alternator Bolt: 36.2-47 ft. lbs. (49-63.7 N.m) | ||
| 3.3L | Alternator Bolt: 36.2-47 ft. lbs. (49-63.7 N.m) | ||
| Drive Belts | |||
| Adjustment | |||
| 2.4L | REPAIR PROCEDURES | ||
| 3.3L | REPAIR PROCEDURES | ||
| Drive Belt Routing | |||
| 2.4L | Refer to Drive Belt figure under INSTALLATION . | ||
| 3.3L | Refer to Drive Belt figure under REMOVAL AND INSTALLATION . | ||
| Engine Cooling | |||
| General Service Specifications | |||
| 2.4L | Refer to Cooling System under SPECIFICATIONS . | ||
| 3.3L | Refer to Cooling System under SPECIFICATIONS . | ||
| Radiator Cap Pressure | 93.16-122.58 kPa (0.95-1.25 kgf/cm2 , 13.51-17.78 psi) | ||
| Thermostat R & I | |||
| 2.4L | THERMOSTAT | ||
| 3.3L | ELECTRIC THERMOSTAT (ECT) | ||
| Water Pump R & I | |||
| 2.4L | WATER PUMP | ||
| 3.3L | WATER PUMP | ||
| Engine Mechanical | |||
| 2.4L | |||
| Compression | COMPRESSION PRESSURE INSPECTION | ||
| Oil Pressure | 117.68 kPa (1.2 kgf/cm2 , 17.06 psi) or above at 1, 000 RPM and oil temperature (oil pan): 110±2°C (230±35.6°F) | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUES | ||
| 3.3L | |||
| Compression | COMPRESSION TEST | ||
| Oil pressure | 130 kPa (1.32 kgf/cm2 , 18.77 psi) at 1000 RPM, 110°C (230°F) and oil temperature (oil pan): 110±2°C (230±35.6°F) | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUES | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| 2.4L | 117.7-127.5 N.m (86.8-94.0 ft. lbs.) | ||
| 3.3L | 71.6-75.5 N.m (52.8-55.9 ft. lbs.) | ||
| Fuel System | |||
| Pressure Specification (Low Pressure Fuel Line) | 480 - 520 kPa (4.9 - 5.3 kgf/cm2 , 69.7 - 75.4 psi) | ||
| Fuel Pressure Test Procedure | |||
| 2.4L | FUEL PRESSURE TEST (LOW PRESSURE SYSTEM) | ||
| 3.3L | FUEL PRESSURE TEST (LOW PRESSURE SYSTEM) | ||
| Fuel Filter Location | Fuel filter is part of fuel pump module. | ||
| Fuel Filter R & I | |||
| 2.4L | FUEL FILTER | ||
| 3.3L | FUEL FILTER | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | |||
| 2.4L | Coil On Plug. | ||
| 3.3L | Coil On Plug. | ||
| Ignition Wires (Routing) | Coil On Plug: | ||
| Spark Plug | |||
| 2.4L - Type: SILZKR7E11 | |||
| Gap | 1.0-1.1 mm (0.0394-0.0433 in.) | ||
| Torque | 14.7-24.5 N.m (1.5-2.5 kgf/cm2 , 10.9-18.0 lb. ft.) | ||
| 3.3L - Type: SILZKR7E11 | |||
| Gap | 1.0-1.1 mm (0.0394-0.0433 in.) | ||
| Torque | 14.7-24.5 N.m (1.5-2.5 kgf/cm2 , 10.8-18.0 lb. ft.) | ||
| Starting | |||
| Starter | |||
| 2.4L | STARTING SYSTEM | ||
| 3.3L | STARTING SYSTEM | ||
| Torque | Starter Bolt: 49.0-63.7 N.m (36.2-47.0 ft. lbs.) | ||
| Wheel Alignment | |||
| Adjustment Specifications | Refer to WHEEL ALIGNMENT . | ||
| Torque | TIGHTENING TORQUE | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 107.9-127.5 N.m (11.0-13.0 kgf/cm2 , 79.6 - 94.0 lb. ft.) | ||