Common Specs & Procedures

SORENTO COMMON SPECS & PROCEDURES

System		Specification/Procedure
Air Conditioning
Service		SPECIFICATIONS
Torque		TIGHTENING TORQUES
Axle Nut/Hub Nut
Front		294.2-313.8 N.m (30.0-32.0 kgf/cm² , 217.0-231.5 lb. ft.)
Rear		294.2-313.8 N.m (30.0-32.0 kgf/cm² , 217.0-231.5 lb. ft.)
Battery
2.0L		BATTERY
2.4L		BATTERY
3.3L		BATTERY .
Brakes
Bleeding Sequence		Refer to BRAKE SYSTEM BLEEDING and ESC BLEEDING OF BRAKE SYSTEM .
Disc Brakes
	Service Specifications	SPECIFICATIONS
	Torque	TIGHTENING TORQUES .
Drum Brakes
	Service Specifications	N/A
	Torque	N/A
Charging
Generator
	2.0L	ALTERNATOR
	2.4L	ALTERNATOR
	3.3L	ALTERNATOR
Torque
	2.0L	Alternator Bolt: 36.2-47 ft. lbs. (49-63.7 N.m)
	2.4L	Alternator Bolt: 36.2-47 ft. lbs. (49-63.7 N.m)
	3.3L	Alternator Bolt: 36.2-47 ft. lbs. (49-63.7 N.m)
Drive Belts
Adjustment
	2.0L	REPAIR PROCEDURES
	2.4L	REPAIR PROCEDURES
	3.3L	REPAIR PROCEDURES
Drive Belt Routing
	2.0L	Refer to Drive Belt figure under REPAIR PROCEDURES .
	2.4L	Refer to Drive Belt figure under REPAIR PROCEDURES .
	3.3L	Refer to Drive Belt figure under REPAIR PROCEDURES .
Engine Cooling
General Service Specifications
	2.0L	Refer to Cooling System under SPECIFICATIONS .
	2.4L	Refer to Cooling System under SPECIFICATIONS .
	3.3L	Refer to Cooling System under SPECIFICATIONS .
	Radiator Cap Pressure	93.16-122.58 kPa (0.95-1.25 kgf/cm² , 13.51-17.78 psi)
	Thermostat R & I
	2.0L	THERMOSTAT
	2.4L	THERMOSTAT
	3.3L	THERMOSTAT
	Water Pump R & I
	2.0L	WATER PUMP
	2.4L	WATER PUMP
	3.3L	WATER PUMP
Engine Mechanical
2.0L
	Compression	COMPRESSION PRESSURE INSPECTION
	Oil Pressure	117.68 kPa (1.2 kgf/cm² , 17.07 psi) or above at 1, 000 RPM and oil temperature (oil pan): 110±2°C (230±35.6°F)
	Overhaul	SPECIFICATIONS
	Torque	TIGHTENING TORQUES
2.4L
	Compression	COMPRESSION PRESSURE INSPECTION
	Oil Pressure	117.68 kPa (1.2 kgf/cm² , 17.06 psi) or above at 1, 000 RPM and oil temperature (oil pan): 110±2°C (230±35.6°F)
	Overhaul	SPECIFICATIONS
	Torque	TIGHTENING TORQUES
3.3L
	Compression	COMPRESSION TEST
	Oil pressure	130 kPa (1.32 kgf/cm² , 18.77 psi) at 1000 RPM, 110°C (230°F) and oil temperature (oil pan): 110±2°C (230±35.6°F)
Overhaul		SPECIFICATIONS
	Torque	TIGHTENING TORQUES
Fluid Specifications		See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flywheel/Flex Plate/Drive Plate Torque
2.0L		117.7-127.5 N.m (86.8-94.0 ft. lbs.)
2.4L		117.7-127.5 N.m (86.8-94.0 ft. lbs.)
3.3L		71.6-75.5 N.m (52.8-55.9 ft. lbs.)
Fuel System
Pressure Specification (Low Pressure Fuel Line)		480 - 520 kPa (4.9 - 5.3 kgf/cm² , 69.7 - 75.4 psi)
	Fuel Pressure Test Procedure
	2.0L	FUEL PRESSURE TEST (LOW PRESSURE SYSTEM)
	2.4L	FUEL PRESSURE TEST (LOW PRESSURE SYSTEM)
	3.3L	FUEL PRESSURE TEST (LOW PRESSURE SYSTEM)
	Fuel Filter Location	Fuel filter is part of fuel pump module.
	Fuel Filter R & I
	2.0L	FUEL FILTER
	2.4L	FUEL FILTER
	3.3L	FUEL FILTER
Ignition
Firing Order & Cylinder Identification		FIRING ORDER & CYLINDER IDENTIFICATION
Ignition Wires (Resistance)
	2.0L	Coil On Plug.
	2.4L	Coil On Plug.
	3.3L	Coil On Plug.
Ignition Wires (Routing)		Coil On Plug:
Spark Plug
2.0L - Type: SILZKR7E9G
	Gap	0.8-0.9 mm (0.0314-0.0354 in.)
	Torque	14.7-24.5 N.m (1.5-2.5 kgf/cm² , 10.9-18.0 lb. ft.)
2.4L - Type: SILZKR7E11
	Gap	1.0-1.1 mm (0.0394-0.0433 in.)
	Torque	14.7-24.5 N.m (1.5-2.5 kgf/cm² , 10.9-18.0 lb. ft.)
3.3L - Type: SILZKR7B11
	Gap	1.0-1.1 mm (0.0394-0.0433 in.)
	Torque	14.7-24.5 N.m (1.5-2.5 kgf/cm² , 10.8-18.0 lb. ft.)
Starting
Starter
	2.0L	STARTING SYSTEM
	2.4L	STARTING SYSTEM
	3.3L	STARTING SYSTEM
Torque		Starter Bolt: 49.0-63.7 N.m (36.2-47.0 ft. lbs.)
Wheel Alignment
	Adjustment Specifications	Refer to WHEEL ALIGNMENT .
	Torque	TIGHTENING TORQUE
Wheel & Tire
Wheel Lug Nut Torque		88.3-107.9 N.m (9.0-11.0 kgf/cm² , 65.1-79.6 lb. ft.)