Repair Procedures: Removal

WARNING: This page is about a different variant/trim than selected.

Remove the following parts;
- Air Cleaner Assembly (A) and Air Duct (B).
  (Refer to "REPAIR PROCEDURES " )
- Battery and battery tray (C).
  (Refer to "REMOVAL, BATTERY/TRAY " )
- ECM (D).
  (Refer to "REMOVAL, ENGINE CONTROL SYSTEM " )
  
  Fig 1: Locating Air Cleaner Assembly And Air Duct
  Courtesy of KIA MOTORS AMERICA, INC.
Disconnect the back up lamp switch (A).

Fig 2: Disconnecting Back Up Lamp Switch
Courtesy of KIA MOTORS AMERICA, INC.
Remove the control cable.
1. Remove the control cable from the control shaft after removing the pins (A).
2. Loosen the control cable bracket bolts (B).
  Tightening Torque:
  
  14.7-21.6 N.m (1.5-2.2 kgf.m, 10.8-15.9 lb-ft)
  
  Fig 3: Loosening Control Cable Bracket Bolts
  Courtesy of KIA MOTORS AMERICA, INC.
Remove the ground cable Bolt (A) and tube bracket Bolt (B).
Tightening Torque:

14.7-21.6 N.m (1.5-2.2 kgf.m, 10.8-15.9 lb-ft)

Fig 4: Removing Ground Cable And Tube Bracket Bolts
Courtesy of KIA MOTORS AMERICA, INC.
Remove the transaxle upper mounting bolts (B-2EA) and the start motor mounting bolts (A-2EA).
Tightening Torque:

(A, B) 42.2-54.0 N.m (4.3-5.5 kgf.m, 31.1-39.8 lb-ft)

Fig 5: Removing Transaxle Upper Mounting Bolts
Courtesy of KIA MOTORS AMERICA, INC.
Remove the Cowl Top Cover.
(Refer to COWL TOP COVER .)
Using the Engine Support Fixture (Support SST No.: 09200-2S200, Adapter SST No.: 09200-1P000, 4X000, Beam SST No.: 09200-38001/3N000), hold the Engine and Transaxle Assembly Safely.

Fig 6: Supporting Engine And Transaxle Assembly Safely
Courtesy of KIA MOTORS AMERICA, INC.
Remove the mounting cover (A).

Fig 7: Locating Mounting Cover
Courtesy of KIA MOTORS AMERICA, INC.
Remove the transaxle support mounting bracket bolts (A-2EA).

Fig 8: Removing Transaxle Support Mounting Bracket Bolts
Courtesy of KIA MOTORS AMERICA, INC.
Remove the transaxle support mounting bracket bolts (A-3EA).
Tightening Torque:

58.8-78.5 N.m (6.0-8.0 kgf.m, 43.4-57.9 lb-ft)

Fig 9: Removing Transaxle Support Mounting Bracket Bolts
Courtesy of KIA MOTORS AMERICA, INC.
Lifting up the vehicle.
Remove the under cover (A).

Fig 10: Removing Under Cover
Courtesy of KIA MOTORS AMERICA, INC.
Remove the clutch release cylinder assembly (A) by removing Bolts (B-2EA).
Tightening Torque:

14.7-21.6 N.m (1.5-2.2 kgf.m, 10.8-15.9 lb-ft)

Fig 11: Removing Clutch Release Cylinder Assembly Bolts
Courtesy of KIA MOTORS AMERICA, INC.
Remove the Drive Shaft Assembly.
(Refer to "DRIVESHAFT ASSEMBLY " .)
Remove the drive shaft cover (A).

Fig 12: Removing Drive Shaft Cover
Courtesy of KIA MOTORS AMERICA, INC.
Remove the brackets (A).

Fig 13: Removing Brackets
Courtesy of KIA MOTORS AMERICA, INC.
Remove the roll rod bracket (C) after removing bolt (A, B).
Tightening Torque:
1. 49.0-63.7 N.m (5.0-6.5 kgf.m, 36.2-47.0 lb-ft)
2. 107.9-127.5 N.m (11.0-13.0 kgf.m, 79.6-94.1 lb-ft)
Fig 14: Removing Roll Rod Bracket Bolts
Courtesy of KIA MOTORS AMERICA, INC.
Remove the mounting bolts (A-3 EA, B-2 EA) of lower part of the transaxle, and the left side cover and remove the transaxle assembly by supporting it with a jack.
CAUTION: Be careful not to damage other system or parts near by when removing the engine and transaxle assembly.

Tightening Torque:
1. 43-49 N.m (4.3-4.9 kgf.m, 31.1-35.4 lb-ft)
2. 42.2-53.9 N.m (4.3-5.5 kgf.m, 31.1-39.8 lb-ft)
Fig 15: Removing Mounting Bolts (A-3 EA, B-2 EA) Of Lower Part Of Transaxle
Courtesy of KIA MOTORS AMERICA, INC.