Common Specs & Procedures Index
OPTIMA HEV COMMON SPECS & PROCEDURES
| System | Specification/Procedure | |
|---|---|---|
| Air Conditioning | ||
| Climate Control Air Filter (Cabin Air Filter) | CLIMATE CONTROL AIR FILTER | |
| Service | SPECIFICATIONS | |
| Torque | Refer to tightening torque specifications included in text under appropriate Repair Procedures in AIR CONDITIONING SYSTEM - OPTIMA HEV article. | |
| Axle Nut/Hub Nut | ||
| Front | 159.1-188.0 ft. lbs. (215.7-254.9 N.m) | |
| Rear | NA | |
| Battery | CHARGING SYSTEM | |
| Brakes | ||
| Bleeding Sequence | BRAKE BLEEDING PROCEDURE | |
| Disc Brakes | SPECIFICATIONS | |
| Drum Brakes | N/A | |
| Torque | See TIGHTENING TORQUES . | |
| Charging | ||
| Generator | CHARGING SYSTEM | |
| Torque | See specs under REMOVAL AND INSTALLATION | |
| Drive Belts | ||
| Adjustment | N/A | |
| Belt Routing | Refer to Installing Drive Belt & Drive Belt Routing figure under INSTALLATION in TIMING SYSTEM article. | |
| Engine Cooling | ||
| General Service Specifications | Refer to Cooling System under SPECIFICATIONS . | |
| Radiator Cap Pressure | 93.16 ~ 122.58 kPa (0.95 ~ 1.25 kgf/cm, 13.51 ~ 17.78 psi) | |
| Thermostat R & I | THERMOSTAT | |
| Water Pump R & I | WATER PUMP | |
| Engine Mechanical | ||
| Compression | Refer to COMPRESSION TEST . Specification is: 1, 283 kPa (13.0 kgf/cm, 185 psi)/200-250 RPM | |
| Oil Pressure | 118 kPa (1.2 kgf/cm, 17.1 psi) or above (at 1, 000 RPM) | |
| Overhaul | SPECIFICATIONS | |
| Torque | TIGHTENING TORQUES | |
| Fluid Specification | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | |
| Flywheel/Flexplate Torque Referred to as a Torsion Damper. |
117.7 ~ 127.5N.m (12.0 ~ 13.0kgf.m, 86.8 ~ 93.9lb-ft) | |
| Fuel System | ||
| Fuel Filter Location | Fuel Filter is part of Fuel Pump Module. | |
| Fuel Filter | Fuel Filter is part of Fuel Pump Module. | |
| Fuel Pump | FUEL PUMP | |
| Pressure Specification | 48.3-51.2 psi (333-353 kPa) | |
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST | |
| Fuel Pressure Release Procedure | RELEASE RESIDUAL PRESSURE IN FUEL LINE | |
| Ignition | ||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | |
| Ignition Wires (Resistance) | Coil On Plug. See INSPECT IGNITION COIL . | |
| Ignition Wires Routing | Coil On Plug | |
| Spark Plugs | ||
| Type | FXU16HR11 | |
| Gap | 1.0 ~ 1.1 mm (0.0394 ~ 0.0433 in.) | |
| Starting | ||
| Starter | NA | |
| Torque (Starter Mounting Bolts) | NA - |
|
| Wheel Alignment | ||
| Adjustment Specifications | WHEEL ALIGNMENT | |
| Torque | TIGHTENING TORQUE | |
| Wheel & Tire | ||
| Lug Nut Torque | 65.1-79.6 ft. lb. (88.3-107.9 N.m) | |