Common Specs & Procedures Index
OPTIMA HEV COMMON SPECS & PROCEDURES
| System | Specification/Procedure | |
|---|---|---|
| Air Conditioning | ||
| Climate Control Air Filter (Cabin Air Filter) | CLIMATE CONTROL AIR FILTER | |
| Service | REPAIR PROCEDURES | |
| Torque | See Tightening Torques table underSPECIFICATIONS | |
| Axle Nut/Hub Nut | ||
| Front | 159.1-188.0 ft. lbs. (215.7-254.9 N.m) | |
| Rear | 57.8-65.0 ft. lbs. (78.4-88.2 N.m) | |
| Battery | AUXILIARY 12V BATTERY | |
| Brakes | ||
| Bleeding Sequence | BLEEDING OF BRAKE SYSTEM | |
| Disc Brakes | SPECIFICATIONS | |
| Drum Brakes | N/A | |
| Torque | See Tightening Torques table under SPECIFICATIONS . | |
| Charging | ||
| Generator | See charging system specifications chart under SPECIFICATION . | |
| Torque | See Tightening Torques table underREPAIR PROCEDURES | |
| Drive Belts | ||
| Adjustment | N/A | |
| Belt Routing | See appropriate figure under REMOVAL AND INSTALLATION . | |
| Engine Cooling | ||
| General Service Specifications | SPECIFICATIONS - REVISED | |
| Radiator Cap Pressure | 93.16 ~ 122.58 kPa (0.95 ~ 1.25 kgf/cm, 13.51 ~ 17.78 psi) | |
| Thermostat R & I | 88±1.5°C (190.4±34.7°F) | |
| Engine Mechanical | ||
| Compression | 1,283 kPa (13.0 kgf/cm, 185 psi) / 200 ~ 250 RPM | |
| Oil Pressure | 118 kPa (1.2 kgf/cm, 17.1 psi) or above | |
| Overhaul | SPECIFICATIONS - REVISED | |
| Torque | SPECIFICATIONS - REVISED | |
| Fluid Specification | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | |
| Flywheel/Flexplate Torque | 117.7 ~ 127.5 N.m (12.0 ~ 13.0 kgf.m, 86.8 ~ 93.9l b-ft) | |
| Fuel System | ||
| Fuel Filter Location | Fuel Filter is part of Fuel Pump Module. | |
| Fuel Filter | Fuel Filter is part of Fuel Pump Module. | |
| Fuel Pump | FUEL PUMP | |
| Pressure Specification | 71.8-73.2 psi (495-505 kPa) | |
| Fuel Pressure Test Procedure | FUEL PUMP | |
| Fuel Pressure Release Procedure | RELEASE RESIDUAL PRESSURE IN FUEL LINE | |
| Ignition | ||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | |
| Ignition Wires (Resistance) | Coil On Plug. See INSPECT IGNITION COIL . | |
| Ignition Wires Routing | Coil On Plug | |
| Spark Plugs | ||
| Type | FXU16HR11 | |
| Gap | 1.0 ~ 1.1 mm (0.0394 ~ 0.0433 in.) | |
| Starting | ||
| Starter | HYBRID STARTER GENERATOR (HSG) | |
| Torque (Starter Mounting Bolts) | M8 bolt: 29.4 ~ 39.2 N.m (3.0 ~ 4.0 kgf.m, 21.7 ~ 28.9 lb-ft) M10 bolts: 44.1 ~ 49.0 N.m (4.0 ~ 5.0 kgf.m, 32.5 ~ 36.2 l b-ft) |
|
| Wheel Alignment | ||
| Adjustment Specifications | ALIGNMENT | |
| Torque | TIGHTENING TORQUE | |
| Wheel & Tire | ||
| Lug Nut Torque | 65.1-79.6 ft. lb. (88.3-107.9 N.m) | |