Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Jeep >> 2020 >> Compass Trailhawk >> Repair and Diagnosis >> Engine Performance >> System >> 2.4L - DTCS P104D To P0140 >> DTC Troubleshooting >> P0108-Manifold Absolute Pressure Sensor Circuit High >> Diagnostic Test

Diagnostic Test

  1. CHECK FOR AN ACTIVE DTC 
    1. Start the engine and allow it to idle.
      WARNING:

      When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing. Failure to follow these instructions may result in possible serious or fatal injury.

    2. With the scan tool, read DTCs and record on the repair order.

      Is the DTC active or pending?

      Yes 

      • Got to 2

      No 

  2. CHECK THE (F856) 5-VOLT SUPPLY CIRCUIT FOR A SHORT TO VOLTAGE 
    1. Turn the ignition off.
    2. Disconnect the MAP Sensor harness connector.
    3. Turn the ignition on.
    4. Measure the voltage on the (F856) 5-Volt Supply circuit at the Manifold Absolute Pressure Sensor harness connector.

      Is the voltage above 5.2 volts?

      Yes 

      • Repair the (F856) 5-Volt Supply circuit for a short to voltage.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .

      No 

      • Got to 3
  3. CHECK THE (K1) MAP SIGNAL CIRCUIT FOR A SHORT TO VOLTAGE 
    1. Measure the voltage on the (K1) MAP Signal circuit at the MAP Sensor harness connector.

      Is the voltage above 5.2 volts?

      Yes 

      • Repair the (K1) MAP Signal circuit for a short to voltage.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .

      No 

      • Got to 4
  4. CHECK FOR THE (K1) MAP SIGNAL CIRCUIT SHORTED TO THE (F856) 5-VOLT SUPPLY CIRCUIT 
    1. Turn the ignition off.
    2. Disconnect the PCM C2 harness connector.
    3. Measure the resistance between the (K1) MAP Signal circuit and the (F856) 5-Volt Supply at the MAP Sensor harness connector.

      Is there continuity between the circuits?

      Yes 

      • Repair the (K1) MAP Signal circuit for a short to the (F856) 5-Volt Supply circuit.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .

      No 

      • Got to 5
  5. CHECK THE (K1) MAP SIGNAL CIRCUIT FOR AN OPEN/HIGH RESISTANCE 
    CAUTION:

    Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals resulting in poor terminal to pin connection. Install the GPEC Diagnostic Adaptor to perform the diagnosis.

    1. Connect the (special tool #10436, Adapter, GPEC Diagnostic).
    2. Measure the resistance of the (K1) MAP Signal between the MAP Sensor harness connector and the GPEC Adaptor.

      Is the resistance below 3.0 Ohms?

      Yes 

      • Got to 6

      No 

      • Repair the (K1) MAP Signal for an open or high resistance.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  6. CHECK THE (K900) SENSOR GROUND CIRCUIT FOR AN OPEN/HIGH RESISTANCE 
    1. Measure the resistance of the (K900) Sensor Ground circuit between the MAP Sensor harness connector and the GPEC Adaptor.

      Is the resistance below 3.0 Ohms?

      Yes 

      • Got to 7

      No 

      • Repair the (K900) Sensor Ground circuit for an open or high resistance.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  7. CHECK THE ABILITY OF THE PCM TO READ THE MAP SENSOR SIGNAL 
    1. Connect the PCM C2 harness connector.
    2. Connect a jumper between the (K900) Sensor Ground circuit and the (K1) MAP Signal circuit at the MAP Sensor harness connector.
    3. Turn the ignition on.
    4. With the scan tool, read the MAP Sensor signal voltage.
      NOTE:

      The scan tool should display the P0107- MANIFOLD ABSOLUTE PRESSURE SENSOR CIRCUIT LOW DTC as active or pending with the jumper in place.

      Does the scan tool display as described above?

      Yes 

      No 

      • Got to 8
  8. CHECK RELATED HARNESS CONNECTIONS 
    1. Disconnect all PCM harness connectors.
    2. Disconnect all related in-line harness connections (if equipped).
    3. Disconnect the related component harness connectors.
    4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
      • Proper connector installation.
      • Damaged connector locks.
      • Corrosion.
      • Other signs of water intrusion.
      • Weather seal damage (if equipped).
      • Bent terminals.
      • Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
      • Terminals that have been pushed back into the connector cavity.
      • Check for spread terminals and verify proper terminal tension.

      Repair any conditions that are found.

    5. Connect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
    6. Connect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
    7. Connect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
    8. With the scan tool, erase DTCs.
    9. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
    10. With the scan tool, read DTCs.

      Did the DTC return?

      Yes 

      No 

scientia non olet · About Mike's Workshop Manuals