Torque Specifications
WARNING: This page is about a different variant/trim than selected.
6.4L ENGINE
| DESCRIPTION | N.m | Ft. Lbs. | In. Lbs. |
|---|---|---|---|
| Air Cleaner Housing - Bolt | 5 | - | 44 |
| Block Pipe Plugs | |||
| (1/4 NPT) | 20 | 15 | - |
| (3/8 NPT) | 27 | 20 | - |
| Water Drain Plugs | 34 | 25 | - |
| Camshaft Sprocket - Bolt | 122 | 90 | - |
| Camshaft Thurst Plate - Bolts | 12 | - | 106 |
| Lifting Stud | 55 | 40 | - |
| Connecting Rod Cap - Bolts | 45 Plus 60° Turn |
33 Plus 60° Turn |
- |
| Main Bearing Cap - Bolts | |||
| M-12 Bolts | 28 Plus 90° Turn |
21 Plus 90° Turn |
- |
| M-8 Bolts (Crossbolts) | 31 | 23 | - |
| Cylinder Head - Bolts (M-12) | Specific torque and fastener pattern required; follow installation sequence. Refer to CYLINDER HEAD, INSTALLATION . | ||
| Cylinder Head Cover - Bolts | 8 | - | 70 |
| Engine Mount Bracket to Engine Block - Bolts | 61 | 45 | - |
| Engine Mount Heat Shield - Nuts | 27 | 20 | - |
| Engine Timing Cover - Bolts | 28 | 21 | - |
| Exhaust Manifold to Cylinder Head - Bolts | 25 | 18 | - |
| Exhaust Manifold to Cylinder Head - Studs | 25 | 18 | - |
| Exhaust Manifold Heat Shield - Stud Nuts | 8 | - | 71 |
| Flexplate to Crankshaft - Bolts | 95 | 70 | - |
| Flywheel to Crankshaft - Bolts | 75 | 55 | - |
| Front Isolator to Engine Mount Bracket- Bolts | 60 | 44 | - |
| Front Isolator to Engine Cradle Crossmember - Bolts | 61 | 45 | - |
| Generator to Engine Block - Bolts | 65 | 48 | - |
| Generator Support Bracket-to-Engine Mount Nut | 28 | 21 | - |
| Heater Tube - Bolt | 11 | 8 | - |
| Intake Manifold - Bolts | Specific torque and fastener pattern required; follow installation sequence. Refer to MANIFOLD, INTAKE, INSTALLATION . | ||
| Lifter Guide Holder - Bolts | 12 | 9 | - |
| MDS Solenoid - Bolts | 11 | 8 | - |
| Oil Control Valve - Bolt | 11 | 8 | - |
| Piston Oil Cooler Jet - Bolts | 13 | 10 | - |
| Power Steering Pump to Engine Block - Bolts | 28 | 21 | - |
| Oil Dipstick Tube - Nut | 31 | 23 | - |
| Oil Pan - Drain Plug | 27 | 20 | - |
| Oil Pan - Bolts | Specific torque and fastener pattern required; follow installation sequence. Refer to PAN, OIL, INSTALLATION . | ||
| Oil Pump - Bolts | 28 | 21 | - |
| Oil Pump Pickup Tube - Bolt and Nut | 28 | 21 | - |
| Rear Seal Retainer - Bolts | 15 | 11 | - |
| Rear Isolator Bracket to Transmission - Bolts (Automatic) | 33 | 24 | - |
| Rear Isolator to Bracket - Bolts (Automatic) | 54 | 40 | - |
| Rear Isolator to Crossmember - Bolts (Automatic) | 61 | 45 | - |
| Rear Isolator to Transmission - Bolts (Manual) | 56 | 41 | - |
| Rear Isolator to Crossmember - Bolts (Manual) | 54 | 40 | - |
| Rocker Arm - Bolts | 22 | 16 | - |
| Strut Tower Support - Bolts | 32 | 28 | - |
| Thermostat Housing - Bolts | 28 | 21 | - |
| Throttle Body - Bolts | 12 | 9 | - |
| Torque Converter to Flexplate - Bolts | 68 | 50 | - |
| Transmission to Engine Block - Bolts | 68 | 50 | - |
| Vibration Damper - Bolt | 250 | 184 | - |
| Water Pump to Engine Timing Cover - Bolts | 28 | 21 | - |