Active Test
WARNING: This page is about a different car, the 2016 Infiniti Q50. However, it is still accessible from the selected car via links, so may be relevant.
The active test is used to determine and identify details of a malfunction, based on self-diagnosis test results and data obtained in the DATA MONITOR. In response to instructions from CONSULT, instead of those from chassis control module on the vehicle, a drive signal is sent to the actuator to check its operation.
CAUTION:
- Never perform ACTIVE TEST while driving the vehicle.
- Always bleed air from brake system before active test.
- Never perform active test when system is malfunctioning.
NOTE:
- When active test is performed while depressing the brake pedal, the brake pedal depressing stroke may change. This is not a malfunction.
- During an active test, sometimes a chassis control warning is displayed and the master warning lamp illuminates on the information display in the combination meter; however, this is not a malfunction.
| Test item | Operation | Description |
|---|---|---|
| BRAKE ACTUATOR 1 MODE 1 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 1 MODE 2 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 1 MODE 3 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 2 MODE 1 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 2 MODE 2 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 2 MODE 3 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 3 MODE 1 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 3 MODE 2 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 3 MODE 3 | Start | Controls brake fluid pressure. |
| COMMAND STEERING ANGLE | Start | Transmits the steering command value 0 deg → 0.00349 deg (hold it for approximately 2 seconds) → 0 deg (hold it for approximately 2 seconds) → 0.00349 deg (hold it for approximately 2 seconds) → 0 deg to the steering force control module. |
| COMMAND ST WHL FORCE | Start | Transmits the steering reaction force command value 0 N → 0.6 N (hold it for approximately 2 seconds) → 0 N (hold it for approximately 2 seconds)→ 0.6 N (hold it for approximately 2 seconds) → 0 N to the steering force control module. |
| MASTER WARNING ACTIVE | On | If touching "On" with the master warning lamp not illuminated, the master warning lamp illuminates. Stops in approximately 1 minute. |
| Off | The master warning lamp turns OFF. (vehicle in normal state) | |
| ALC DISP | On | Displays Active Lane Control active status on the information display in the combination meter. |
| Off | Displays Active Lane Control inactive status on the information display in the combination meter. | |
| FL TIRE DISP | On | Displays the front LH tire on the information display in the combination meter. |
| Off | Does not display the front LH tire on the information display in the combination meter. | |
| FR TIRE DISP | On | Displays the front RH tire on the information display in the combination meter. |
| Off | Does not display the front RH tire on the information display in the combination meter. | |
| RL TIRE DISP | On | Displays the rear LH tire on the information display in the combination meter. |
| Off | Does not display the rear LH tire on the information display in the combination meter. | |
| RR TIRE DISP | On | Displays the rear RH tire on the information display in the combination meter. |
| Off | Does not display the rear RH tire on the information display in the combination meter. | |
| TURN DISP | NO DISP | Does not display the turning status on the information display in the combination meter. |
| LH | Displays the LH turning status on the information display in the combination meter. | |
| RH | Displays the RH turning status on the information display in the combination meter. | |
| ALC LEVEL | LEVEL 1 | Displays Active Lane Control corresponding to the selected level on the information display in the combination meter. |
| LEVEL 2 | ||
| LEVEL 3 | ||
| LEVEL 4 | ||
| ALC SETTING | On | Displays Active Lane Control active status on the information display in the combination meter. |
| Off | Displays Active Lane Control inactive status on the information display in the combination meter. | |
| ATC 1 DISP | On | Displays active trace control function active status on the information display in the combination meter. |
| Off | Displays active trace control function inactive status on the information display in the combination meter. | |
| ATC 2 DISP | On | Displays active trace control function active status on the information display in the combination meter. |
| Off | Displays active trace control function inactive status on the information display in the combination meter. | |
| ATC 4 DISP | On | Displays active trace control function active status on the information display in the combination meter. |
| Off | Displays active trace control function inactive status on the information display in the combination meter. | |
| FR shock absorber* | Soft | Controls front right shock absorber. |
| Medium | ||
| Hard | ||
| FL shock absorber* | Soft | Controls front left shock absorber. |
| Medium | ||
| Hard | ||
| RR shock absorber* | Soft | Controls rear right shock absorber. |
| Medium | ||
| Hard | ||
| RL shock absorber* | Soft | Controls rear left shock absorber. |
| Medium | ||
| Hard | ||
| All shock absorber* | Soft | Controls all shock absorber. |
| Medium | ||
| Hard |
* : Models with digital motion control