Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Infiniti >> 2015 >> QX50 Base, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 42 (Driver Assistance System (ADAS Control Unit) (Introduction) (Hybrid)) >> ADAS Control Unit >> System Description >> Diagnosis System (ADAS Control Unit) >> Consult Function (ICC/ADAS) >> Display Items For The Cause Of Automatic Cancellation 2

Display Items For The Cause Of Automatic Cancellation 2

WARNING: This page is about a different car, the 2015 Infiniti Q70. However, it is still accessible from the selected car via links, so may be relevant.
Cause of cancellation Lane departure prevention Blind spot intervention Description
OPE VDC/TCS/ABS 1 *   The activation of VDC, TCS, or ABS during LDP system control
Vehicle dynamics *   Vehicle behavior exceeds specified value
Steering speed *   Steering speed was more than the specified value in evasive direction
End by yaw angle *   Yaw angle was the end of LDP control
Departure yaw large *   Detected more than the specified value of yaw angle in departure direction
ICC WARNING *   Target approach warning of ICC system, FEB system, or PFCW system was activated
CURVATURE *   Road curve was more than the specified value
Steering angle large *   Steering angle was more than the specified value
Brake is operated *   Brake pedal was operated
IGN LOW VOLT *   Decrease in ADAS control unit IGN voltage
Lateral offset *   Distance of vehicle and lane was detached in lateral direction more than the specified value
Lane marker lost *   Lane camera unit lost the trace of lane marker
Lane marker unclear *   Detected lane marker was unclear
Yaw acceleration *   Detected yawing speed was more than the specified value
Deceleration large *   Deceleration in a longitudinal direction was more than the specified value
Accel is operated *   Accelerator pedal was depressed
Departure steering *   Steering wheel was steered more than the specified value in departure direction
Evasive steering *   Steering wheel was steered more than the specified value in the evasive direction
R range *   Selector lever was operated to R range
Parking brake drift *   Rear wheels lock was detected
Not operating condition *   Did not meet the operating condition (vehicle speed, turn signal operation, etc.)
SNOW MODE SW *   Shifting of the drive mode selector to SNOW position
VDC OFF SW *   VDC OFF switch was pressed
OPE VDC/ABS 2 *   The activation of VDC or ABS during a standby time of LDP system control
4WD LOCK MODE *  
NOTE:

The item is displayed, but not used

BSI WARNING *   Blind Spot Intervention system was activated
BSI) OPE VDC/TCS/ABS 1   * The activation of VDC, TCS, or ABS during Blind Spot Intervention system control
BSI) Vehicle dynamics   * Vehicle behavior exceeds specified value
BSI) Steering speed   * Steering speed was more than the specified value in evasive direction
BSI) End by yaw angle   * Yaw angle was the end of Blind Spot Intervention control
BSI) Departure yaw large   * Detected more than the specified value of yaw angle in departure direction
BSI) ICC WARNING   * Target approach warning of ICC system, FEB system or PFCW system was activated
BSI) CURVATURE   * Road curve was more than the specified value
BSI) Steering angle large   * Steering angle was more than the specified value
BSI) Brake is operated   * Brake pedal was operated
BSI) IGN LOW VOLT   * Decrease in ADAS control unit IGN voltage
BSI) Lateral offset   * Distance of vehicle and lane was detached in lateral direction more than the specified
BSI) Lane marker lost   * Lane camera unit lost the trace of lane marker
BSI) Lane marker unclear   * Detected lane marker was unclear
BSI) Yaw acceleration   * Detected yawing speed was more than the specified value
BSI) Deceleration large   * Deceleration in a longitudinal direction was more than the specified value
BSI) Accel is operated   * Accelerator pedal was depressed
BSI) Departure steering   * Steering wheel was steered more than the specified value in departure direction
BSI) Evasive steering   * Steering wheel was steered more than the specified value in the evasive direction
BSI) R range   * Selector lever was operated to R range
BSI) Parking brake drift   * Rear wheels lock was detected
BSI) SNOW MODE SW   * SNOW mode switch was pressed
BSI) VDC OFF SW   * VDC OFF switch was pressed
BSI) OPE VDC/ABS 2   * The activation of VDC or ABS during a standby time of Blind Spot Intervention system control
BSI) Not operating condition   * Did not meet the operating condition (vehicle speed, turn signal operation, etc.)
BSI) 4WD LOCK MODE   *
NOTE:

The item is displayed, but not used

Side Radar Lost   * Unrecognized side radar LH or RH by the ADAS control unit
NO RECORD * * -