Trouble Diagnosis Symptom Chart

Make sure other systems using the signal of the following systems operate normally.

TROUBLE DIAGNOSIS SYMPTOM CHART

Symptom	Repair order	Refer to
None of the power windows can be operated using any switch.	1. Check BCM power supply and ground circuit	CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
	2. Check power window main switch power supply and ground circuit	CHECK POWER WINDOW MAIN SWITCH POWER SUPPLY CIRCUIT
	3. Check power window serial link	CHECK POWER WINDOW SERIAL LINK (PASSENGER SIDE)
Driver side power window alone does not operate.	1. Check power window motor (front driver side) circuit	CHECK POWER WINDOW MOTOR (FRONT DRIVER SIDE) CIRCUIT
Driver side power window alone does not operate.	2. Replace power window main switch	-
Front passenger side power window alone does not operate.	1. Check power window main switch power supply and ground circuit check	CHECK POWER WINDOW MAIN SWITCH POWER SUPPLY CIRCUIT
	2. Check power window sub-switch (front passenger side) power and ground circuit	CHECK POWER WINDOW SUB-SWITCH (FRONT PASSENGER SIDE) POWER SUPPLY AND GROUND CIRCUIT
	3. Check power window serial link	CHECK POWER WINDOW SERIAL LINK (PASSENGER SIDE)
	4. Check power window motor (front passenger side) circuit	CHECK POWER WINDOW MOTOR (FRONT PASSENGER SIDE) CIRCUIT
	5. Replace BCM	REMOVAL AND INSTALLATION OF BCM
Rear LH or RH side power window alone does not operate	1. Check power window sub-switch (rear LH or RH) power and ground circuit	CHECK POWER WINDOW SUB-SWITCH (REAR LH OR RH) POWER SUPPLY AND GROUND CIRCUIT
	2. Check power window serial link (rear LH or RH)	CHECK POWER WINDOW SERIAL LINK (REAR LH OR RH)
	3. Check power window motor (rear LH or RH) circuit	CHECK POWER WINDOW MOTOR (REAR LH OR RH) CIRCUIT
	4. Replace rear power window switch (LH or RH)	-
Anti-pinch system does not operate normally (driver side)	1. Initialization	SYSTEM INITIALIZATION
	2. Door window sliding part malfunction A foreign material adheres to window glass or glass run rubber. Glass run rubber wear or deformation. Sash is tilted too much, or no enough.	-
	3. Encoder circuit check (driver side)	CHECK POWER WINDOW MOTOR (REAR LH OR RH) CIRCUIT
Anti-pinch system does not operate normally (passenger side)	1. Initialization	SYSTEM INITIALIZATION
	2. Door window sliding part malfunction A foreign material adheres to window glass or glass run rubber. Glass run rubber wear or deformation. Sash is tilted too much, or no enough.	-
	3. Encoder circuit check (passenger side)	CHECK ENCODER CIRCUIT (PASSENGER SIDE)
Anti-pinch system does not operate normally (rear LH or RH)	1. Initialization	SYSTEM INITIALIZATION
	2. Door window sliding part malfunction A foreign material adheres to window glass or glass run rubber. Glass run rubber wear or deformation. Sash is tilted too much, or no enough.	-
	3. Encoder circuit check (rear LH or RH)	CHECK ENCODER CIRCUIT (REAR LH OR RH)
Power window retained power operation does not operate properly	1. Check the retained power operation mode setting.	CONSULT-III FUNCTION (BCM)
	2. Check door switch	CHECK DOOR SWITCH
	3. Replace BCM.	REMOVAL AND INSTALLATION OF BCM
Does not operate by key cylinder switch	1. Initialization	SYSTEM INITIALIZATION
	2. Check door key cylinder switch	CHECK FRONT DOOR KEY CYLINDER SWITCH
	3. Replace power window main switch	-
Power window lock switch does not function	Check power window lock switch	CHECK POWER WINDOW LOCK SWITCH
Auto operation does not operate but manual operate normally (driver side)	1. Initialization	SYSTEM INITIALIZATION
	2. Check encoder circuit (driver side)	CHECK ENCODER CIRCUIT (DRIVER SIDE)
	3. Replace power window main switch	-
Auto operation does not operate but manual operate normally (passenger side)	1. Initialization	SYSTEM INITIALIZATION
	2. Encoder circuit check (passenger side)	CHECK ENCODER CIRCUIT (PASSENGER SIDE)
	3. Replace front power window switch (passenger side)	-
Auto operation does not operate but manual operate normally (rear LH or RH)	1. Initialization	SYSTEM INITIALIZATION
	2. Check encoder circuit (rear LH or RH)	CHECK ENCODER CIRCUIT (REAR LH OR RH)
	3. Replace rear power window switch (LH or RH)	-