Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Infiniti >> 2007 >> M35 Base >> Repair and Diagnosis >> Transmission >> Automatic Transmission >> On-Vehicle Service >> Control Valve, TCM and A/T Fluid Temperature Sensor 2 >> A/T Fluid Temperature Sensor 2 Removal And Installation >> Installation

A/T Fluid Temperature Sensor 2 Removal And Installation: Installation

CAUTION: After completing installation, check for A/T fluid leakage and A/T fluid level. Refer to "CHECKING A/T FLUID ".
  1. Install A/T fluid temperature sensor 2 to bracket.
    Fig 1: Identifying Bracket And A/T Fluid Temperature Sensor
    G04875918
  2. Install A/T fluid temperature sensor 2 (with bracket) in control valve with TCM. Tighten A/T fluid temperature sensor 2 bolts to the specified torque. Refer to "COMPONENTS ".
    Fig 2: Adjusting Bolt Hole Of Bracket To Bolt Hole Of Control Valve With TCM
    G04901144
  3. Connect A/T fluid temperature sensor 2 connector.
    Fig 3: Connecting A/T Fluid Temperature Sensor 2 Connector
    G04901114
  4. Securely fasten A/T fluid temperature sensor 2 harness with terminal clip.
    Fig 4: Connecting A/T Fluid Temperature Sensor 2 Connector
    G04901143
  5. Install oil pan, oil pan gasket and clips (VQ35DE models) or oil pan, oil pan gasket, brackets and clips (VK45DE models) according to the following procedures.
    1. VQ35DE models
      1. Install oil pan gasket to oil pan.
        CAUTION:
        • Do not reuse oil pan gasket.
        • Install it in the direction to align hole positions.
        • Complete remove all moisture, oil and old gasket, etc. from oil pan gasket mounting surface.
      2. Install oil pan (2) (with oil pan gasket) and clips (1) to transmission case.

        <=: Front

        : Bolt (22)

        Fig 5: Locating Oil Pan Gasket And Clips (VQ35DE Models)
        G05213359
        CAUTION:
        • Install it so that drain plug comes to the position as shown in the figure.
        • Be careful not to pinch harnesses.
        • Completely remove all moisture, oil and old gasket, etc. from oil pan mounting surface.
      3. Tighten oil pan mounting bolts to the specified torque in numerical order shown in the figure after temporarily tightening them. Tighten oil pan mounting bolts to the specified torque. Refer to "COMPONENTS ".
        CAUTION: Do not reuse oil pan mounting bolts.
        Fig 6: Identifying Oil Pan Bolts Tightening Sequence
        G04875938
    2. VK45DE models
      1. Install oil pan gasket to oil pan.
        CAUTION:
        • Do not reuse oil pan gasket.
        • Install it in the direction to align hole positions.
        • Complete remove all moisture, oil and old gasket, etc. from oil pan gasket mounting surface.
      2. Install oil pan (3) (with oil pan gasket), clips (1) and brackets (2) to transmission case.

        <=: Front

        : Bolt (22)

        CAUTION:
        • Install it so that drain plug comes to the position as shown in the figure.
        • Be careful not to pinch harnesses.
        • Completely remove all moisture, oil and old gasket, etc. from oil pan mounting surface.
        • Be careful with installation direction of brackets (2).
          Fig 7: Locating Oil Pan Gasket And Clips (VK45DE Models)
          G05213360
      3. Tighten oil pan mounting bolts to the specified torque in numerical order shown in the figure after temporarily tightening them. Tighten oil pan mounting bolts to the specified torque. Refer to "COMPONENTS ".
        CAUTION: Do not reuse oil pan mounting bolts.
  6. Install drain plug to oil pan. Tighten drain plug to the specified torque. Refer to "COMPONENTS ".
    CAUTION: Do not reuse drain plug gasket.
  7. Connect heated oxygen sensor 2 harness connector.
  8. Pour ATF into A/T assembly. Refer to "CHANGING A/T FLUID ".
  9. Connect the battery cable to the negative terminal.
    Fig 8: Identifying Oil Pan Bolts Tightening Sequence
    G04875938
scientia non olet · About Mike's Workshop Manuals