Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Infiniti >> 2007 >> M35 Base >> Repair and Diagnosis >> Body & Frame >> Windows >> Glass, Window System & Mirrors >> Reverse Interlock Door Mirror System >> Check Changeover Switch Circuit

Check Changeover Switch Circuit

  1. CHECK CHANGEOVER SWITCH SIGNAL 

    With CONSULT-II 

    Check the operation on (MIR CHNG SW-R" or "MIR CHNG SW-L) in the DATA MONITOR.

    DATA MONITOR REFERENCE VALUE CHART

    Monitor item
    [OPERATION or UNIT]    		 Contents
    MIR CHNG SW-R "ON/OFF" ON/OFF status judged from the changeover switch (switching to RIGHT) signal is displayed.
    MIR CHNG SW-L "ON/OFF" ON/OFF status judged from the changeover switch (switching to LEFT) signal is displayed.
    Fig 1: CONSULT II Display - DATA MONITOR
    G04903045

    Without CONSULT-II 

    1. Turn ignition switch ON.
    2. Check voltage between automatic drive positioner control unit connector and ground.
      VOLTAGE SPECIFICATION

      Terminals Change over switch condition Voltage (V) (Approx.)
      (+) (-)
      Automatic drive positioner control unit connector Terminal
      M6 2 Ground RIGHT 0
      Other than above 5
      18 LEFT 0
      Other than above 5

    OK or NG 

    OK: Changeover switch circuit is OK.

    NG: GO TO 2.

    Fig 2: Checking Voltage Between Automatic Drive Positioner Control Unit Connector And Ground
    G05212700
  2. CHECK HARNESS CONTINUITY 
    1. Turn ignition switch OFF.
    2. Disconnect automatic drive positioner control unit and door mirror remote control switch connector.
    3. Check continuity between automatic drive positioner control unit connector and door mirror remote control switch connector.
      CONTINUITY SPECIFICATION

      A B Continuity
      Automatic drive positioner control unit connector Terminal Door mirror remote control switch connector Terminal
      M6 2 M95 3 Yes
      18 2
    4. Check continuity between automatic drive positioner control unit connector and ground.
      CONTINUITY SPECIFICATION

      A Ground Continuity
      Automatic drive positioner control unit connector Terminal No
      M6 2
      18
      Fig 3: Checking Continuity Between Automatic Drive Positioner Control Unit Connector And Ground
      G05212701

    OK or NG 

    OK: GO TO 3.

    NG: Repair or replace harness.

  3. CHECK CHANGEOVER SWITCH 

    Check door mirror remote control switch.

    CHANGEOVER SWITCH SPECIFICATION

    Terminal Change over switch condition Continuity
    Door mirror remote control switch
    2 13 LEFT Yes
    Other than above No
    3 RIGHT Yes
    Other than above No
    Fig 4: Checking Door Mirror Remote Control Switch
    G05212702

    OK or NG 

    OK: GO TO 4.

    NG: Replace door mirror remote control switch.

  4. CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT 

    Check continuity between door mirror remote control switch connector and ground.

    CONTINUITY SPECIFICATION

    Door mirror remote control switch connector Terminal Ground Continuity
    M95 13 Yes

    OK or NG 

    OK: GO TO 5.

    NG: Repair or replace harness.

    Fig 5: Checking Continuity Between Door Mirror Remote Control Switch Connector And Ground
    G05212703
  5. CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL 
    1. Connect automatic drive positioner control unit connector.
    2. Turn ignition switch ON.
    3. Check voltage between automatic drive positioner control unit connector and ground.
      VOLTAGE SPECIFICATION

      Terminals Voltage (V) (Approx.)
      (+) (-)
      Automatic drive positioner control unit connector Terminal
      M6 2 Ground 5
      18
      Fig 6: Checking Voltage Between Automatic Drive Positioner Control Unit Connector And Ground
      G05212700

    OK or NG 

    OK: Check the condition of harness and connector.

    NG: Replace automatic drive positioner control unit.

scientia non olet · About Mike's Workshop Manuals