Common Specs & Procedures
SONATA PHEV COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | |||
| PHEV | SPECIFICATIONS | ||
| Torque | |||
| PHEV | Refer to TIGHTENING TORQUES . | ||
| Axle Nut/Hub Nut | |||
| Front | |||
| PHEV | 274.6-294.2 N.m (28.0-30.0 kgf.m, 202.5-217.1 lb-ft) | ||
| Rear | |||
| PHEV | NA | ||
| Battery | |||
| PHEV | Refer to CHARGING SYSTEM SPECIFICATIONS table under CHARGING SYSTEM . | ||
| Brakes | |||
| Bleeding Sequence | |||
| PHEV | Refer to BRAKE BLEEDING PROCEDURES . Also refer to AHB BRAKE SYSTEM BLEEDING PROCEDURE . | ||
| Disc Brakes: Service Specifications | |||
| PHEV | Refer to SPECIFICATIONS . | ||
| Disc Brakes: Torque | |||
| PHEV | Refer to TIGHTENING TORQUES . | ||
| Charging | |||
| Generator | |||
| PHEV | Refer to CHARGING SYSTEM and SPECIFICATIONS . | ||
| Torque | |||
| PHEV | LOW VOLTAGE DC/DC CONVERTER (LDC) | ||
| Drive Belts | |||
| Adjustment | Serpentine Belt Used | ||
| Drive Belt Routing | |||
| PHEV | Refer to "Installing Drive Belt" figure under INSTALLATION . | ||
| Engine Cooling | |||
| General Service Specifications | |||
| PHEV | Refer to Cooling System under SPECIFICATIONS | ||
| Radiator Cap Pressure | 13.51-17.78 psi | ||
| Thermostat R & I | |||
| PHEV | THERMOSTAT | ||
| Water Pump R & I | |||
| PHEV | ENGINE ELECTRIC WATER PUMP (EEWP) | ||
| Engine Mechanical | |||
| PHEV | |||
| Compression | COMPRESSION PRESSURE INSPECTION | ||
| Oil pressure | 11.38 psi or above at 1000 RPM. | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUES | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| PHEV (Referred to as a Torsion Damper). | 117.7 ~ 127.5N.m (12.0 ~ 13.0kgf.m, 86.8 ~ 93.9lb-ft) | ||
| Fuel System | |||
| Pressure Specification | |||
| PHEV | 71.8-73.2 psi (495-505 kPa) | ||
| Fuel Pressure Test Procedure | |||
| PHEV | FUEL PRESSURE TEST | ||
| Fuel Filter R & I | |||
| PHEV | FUEL FILTER | ||
| Ignition | |||
| Firing Order & Cylinder Identification | Refer to FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Spark Plug | |||
| Type | |||
| PHEV | SILZKR7E9 | ||
| Gap | |||
| PHEV | 0.8-0.9 mm (0.0315-0.0354 in.) | ||
| Torque | |||
| PHEV | 14.7-24.5 N.m (1.5-2.5 kgf.m, 10.8-18.0 lb-ft | ||
| Starting | |||
| PHEV | |||
| Starter | HYBRID STARTER GENERATOR (HSG) | ||
| Torque | 44.1 ~ 53.9 N.m (4.5 ~ 5.5 kgf.m, 32.5 ~ 39.8 lb-ft) | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| PHEV | WHEEL ALIGNMENT | ||
| Torque | |||
| PHEV | TIGHTENING TORQUE | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 88.3-107.9 N.m (65.1-79.6 lb-ft) | ||