Repair Procedures: Removal

WARNING: This page is about a different variant/trim than selected.

Remove the following items;

Engine cover (A).
(Refer to "INTAKE & EXHAUST SYSTEM " )
Air cleaner assembly (B) and air duct (C).
(Refer to "INTAKE & EXHAUST SYSTEM " )
Battery and battery tray (D).
(Refer to "BATTERY " )

ECM (E).

(Refer to "ENGINE CONTROL MODULE (ECM) " )

Courtesy of HYUNDAI MOTOR AMERICA

Disconnect the vehicle speed sensor connector (A).
Remove the back up lamp switch connector (B).

Courtesy of HYUNDAI MOTOR AMERICA
Remove the ground cable from transaxle (A).

Courtesy of HYUNDAI MOTOR AMERICA
Disconnect the shift cable bracket bolts (B-3ea) after removing the washer and pin (A).

Courtesy of HYUNDAI MOTOR AMERICA
Remove the tube bracket bolt (A).
Tightening Torque:

14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.8 ~ 15.9 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the transaxle upper mounting bolt (B-2ea) and the start motor mounting bolt (A-2ea).
Tightening Torque:

(A, B) 42.2 ~ 54.0 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the hood assembly.
(Refer to "HOOD " .)
Remove the cowl top cover.
(Refer to "CONSOLE " .)
Remove the wiper motor.
(Refer to "FRONT WIPER MOTOR " .)
Remove the cowl complete assembly panel (A).

Courtesy of HYUNDAI MOTOR AMERICA
Using the engine support fixture (Support SST No.: 09200-2S200, Adapter SST No.: 09200-2S100, Beam SST No.: 09200-38001/3N000), hold the engine and transaxle assembly safely.

Courtesy of HYUNDAI MOTOR AMERICA
Remove the mounting cover (A).

Courtesy of HYUNDAI MOTOR AMERICA
Remove the transaxle support mounting bracket bolts (A-2ea).
Tightening torque:

88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the transaxle support mounting bracket (A).
Tightening torque:

58.9 ~ 78.5 N.m (6.0 ~ 8.0 kgf.m, 43.4 ~ 57.9 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the under cover (A).

Courtesy of HYUNDAI MOTOR AMERICA
Remove the drive shaft assembly.
(Refer to "DRIVESHAFT ASSEMBLY " .)
Remove the clutch release cylinder assembly (B) after removing the nuts (A-2ea).
Tightening torque:

14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.8 ~ 15.9 lb-ft)

Courtesy of
Remove the roll rod support bracket (C) after removing bolt (A, B).
Tightening torque:

(A) 49.0 ~ 68.6 N.m (5.0 ~ 7.0 kgf.m, 36.2 ~ 50.6 lb-ft)

(B) 107.9 ~ 127.5 N.m (11.0 ~ 13.0 kgf.m, 79.6 ~ 94.1 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA
Remove the drive shaft cover (A).

Courtesy of HYUNDAI MOTOR AMERICA
Remove the brackets (A).

Courtesy of
Remove the lower mounting bolts (A-3ea, B-2ea) of lower part of the transaxle, and the left side cover and remove the transaxle assembly by supporting it with a jack.
CAUTION: Be careful not to damage other system or parts near by when removing the engine and transaxle assembly.

Tightening Torque:

(A) 43 ~ 49 N.m (4.3 ~ 4.9 kgf.m, 31.1 ~ 35.4 lb-ft)

(B) 43 ~ 55 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA