DTC 2622
DTC 2622 : TCU Diag
NOTE:
- Check the vehicle 12 volt battery condition first .
- This navigation DTC sets when NG is indicated in the TCU diagnosis (The TCU icon is red in the System Links).
- Before you troubleshoot, make sure to follow the General Troubleshooting Information .
- Problem verification
-1. Clear the hard error codes .
-2. Turn the vehicle to the OFF (LOCK) mode then the ON mode.
-3. Check for hard error codes .
Is DTC 2622 indicated?
YES
The failure is duplicated, go to step 2.
NO
Intermittent failure, the system is OK at this time.
- Shorted wire check (TEL AUDIO+, TEL AUDIO- lines)
-1. Turn the vehicle to the OFF (LOCK) mode.
-2. Open the driver's door, and wait more than 1 minute.
-3. Disconnect the following connectors.
Telematics control unit connector A (32P) Audio-navigation unit connector F (36P) -4. Check for continuity between test points 1 and 2.
Test condition Vehicle OFF (LOCK) mode Telematics control unit connector A (32P): disconnected Audio-navigation unit connector F (36P): disconnected Test point 1 Telematics control unit connector A (32P) No. 12 Test point 2 Body ground Test point 1 Telematics control unit connector A (32P) No. 13 Test point 2 Body ground Is there continuity?
YES
There is a short to body ground in the wire (s). Replace the affected shielded harness.
NO
The TEL AUDIO+ and TEL AUDIO- wires are not shorted to ground. Go to step 3.
- Shorted wire check (TEL AUDIO+ line to another lines)
-1. Check for continuity between test points 1 and 2.
Test condition Vehicle OFF (LOCK) mode Telematics control unit connector A (32P): disconnected Audio-navigation unit connector F (36P): disconnected Test point 1 Telematics control unit connector A (32P) No. 12 Test point 2 Telematics control unit connector A (32P) No. 13 Test point 1 Telematics control unit connector A (32P) No. 12 Test point 2 Telematics control unit connector A (32P) No. 28 Is there continuity?
YES
There is a short in the wire (s). Replace the affected shielded harness.
NO
The TEL AUDIO+ wire is not shorted. Go to step 4.
- Open wire check (TEL AUDIO+, TEL AUDIO- lines)
-1. Check for continuity between test points 1 and 2.
Test condition Vehicle OFF (LOCK) mode Telematics control unit connector A (32P): disconnected Audio-navigation unit connector F (36P): disconnected Test point 1 Telematics control unit connector A (32P) No. 12 Test point 2 Audio-navigation unit connector F (36P) No. 35 Test point 1 Telematics control unit connector A (32P) No. 13 Test point 2 Audio-navigation unit connector F (36P) No. 17 Is there continuity?
YES
The TEL AUDIO+ and the TEL AUDIO- wires are OK. Go to step 5.
NO
There is an open in the wire (s). Replace the affected shielded harness.
- Open wire check (TEL USB lines)
-1. Turn the vehicle to the OFF (LOCK) mode.
-2. Open the driver's door, and wait more than 1 minute.
-3. Disconnect the following connectors.
Audio-navigation unit connector M (10P) Telematics control unit connector B (5P) -4. Check for continuity between test points 1 and 2.
Test condition OFF (LOCK) mode Audio-navigation unit connector M (10P): disconnected Telematics control unit connector B (5P): disconnected Test point 1: Test point 2: No. 6 No. 1 No. 7 No. 2 No. 8 No. 3 No. 9 No. 4 Is there continuity?
YES
The TEL USB wires are OK. Go to step 6.
NO
There is an open in the wire (s). Replace the affected shielded harness.
- Telematics control unit check
-1. Substitute a known-good Telematics control unit .
-2. Reconnect all the connectors.
-3. Turn the vehicle to the ON mode.
-4. Clear the hard error codes .
-5. Turn the vehicle to the OFF (LOCK) mode then the ON mode.
-6. Check for hard error codes .
Is DTC 2622 indicated?
YES
Replace the audio-navigation unit .
NO
Replace the original telematics control unit.