Power Steering
Diagnostics in this service information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| DTC | Description | Action |
|---|---|---|
| C0051:23 | Steering Wheel Position Sensor: Signal Stuck Low | GO to Pinpoint Test AG |
| C0051:27 | Steering Wheel Position Sensor: Signal Rate Of Change Above Threshold | GO to Pinpoint Test AG |
| C0051:28 | Steering Wheel Position Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure | GO to Pinpoint Test AG |
| C0051:29 | Steering Wheel Position Sensor: Signal Invalid | GO to Pinpoint Test AG |
| C0051:54 | Steering Wheel Position Sensor: Missing Calibration | GO to Pinpoint Test AG |
| C0051:62 | Steering Wheel Position Sensor: Signal Compare Failure | GO to Pinpoint Test AG |
| C0051:64 | Steering Wheel Position Sensor: Signal Plausibility Failure | GO to Pinpoint Test AG |
| C0051:67 | Steering Wheel Position Sensor: Signal Incorrect After Event | GO to Pinpoint Test AG |
| C0051:82 | Steering Wheel Position Sensor: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AG |
| C0051:85 | Steering Wheel Position Sensor: Signal Above Allowable Range | GO to Pinpoint Test AG |
| C0051:86 | Steering Wheel Position Sensor: Signal Invalid | GO to Pinpoint Test AG |
| C0051:96 | Steering Wheel Position Sensor: Component Internal Failure | GO to Pinpoint Test AG |
| C006B:00 | Stability System Active Too Long: No Sub Type Information | GO to Pinpoint Test AG |
| B1D23:4B | Overheat Sensor: Over Temperature | GO to Pinpoint Test BB |
| C1110:56 | Power steering Calibration Data: Invalid/Incompatible Configuration | GO to Pinpoint Test AA |
| C1B00:49 | Steering Angle Sensor: Internal Electronic Failure | GO to Pinpoint Test BF |
| C1B00:62 | Steering Angle Sensor: Signal Compare Failure | GO to Pinpoint Test BF |
| C200B:49 | Steering Shaft Torque Sensor 1: Internal Electronic Failure | GO to Pinpoint Test BG |
| C200B:62 | Steering Shaft Torque Sensor 1: Signal Compare Failure | GO to Pinpoint Test BG |
| C200D:49 | Motor Rotation Angle Sensor: Internal Electronic Failure | GO to Pinpoint Test BI |
| C200D:62 | Motor Rotation Angle Sensor: Signal Compare Failure | GO to Pinpoint Test BI |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test AJ |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test AK |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AL |
| U0146:00 | Lost Communication With Serial Data Gateway "A": No Sub Type Information | GO to Pinpoint Test AM |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AN |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AO |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test AP |
| U0212:00 | Lost Communication With Steering Column Control Module: No Sub Type Information | GO to Pinpoint Test AQ |
| U023A:00 | Lost Communication With Image Processing Module A: No Sub Type Information | GO to Pinpoint Test AR |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | GO to Pinpoint Test AS |
| U0415:00 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test AT |
| U0415:22 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": Signal Amplitude Greater Than Maximum | GO to Pinpoint Test AT |
| U0429:00 | Invalid Data Received From Steering Column Control Module: No Sub Type Information | GO to Pinpoint Test AU |
| U0447:00 | Invalid Data Received From Serial Data Gateway "A": No Sub Type Information | GO to Pinpoint Test AV |
| U045A:00 | Invalid Data Received From Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test AW |
| U053B:00 | Invalid Data Received From Image Processing Module A: No Sub Type Information | GO to Pinpoint Test AX |
| U2016:09 | Control Module Main Software: Component Failures | GO to Pinpoint Test BO |
| U2016:47 | Control Module Main Software: Watchdog/Safety μC Failure | GO to Pinpoint Test BO |
| U2016:48 | Control Module Main Software: Supervision Software Failure | GO to Pinpoint Test BO |
| U2016:57 | Control Module Main Software: Invalid/Incompatible Software Component | GO to Pinpoint Test BO |
| U2016:66 | Control Module Main Software: Signal Has Too Many Transitions/Events | GO to Pinpoint Test BO |
| U2016:94 | Control Module Main Software: Unexpected Operation | GO to Pinpoint Test BO |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test BQ |
| U2300:55 | Central Configuration: Not Configured | GO to Pinpoint Test AB |
| U3000:05 | Control Module: System Programming Failures | GO to Pinpoint Test B |
| U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test B |
| U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test B |
| U3000:61 | Control Module: Signal Calculation Failure | GO to Pinpoint Test B |
| U3000:66 | Control Module: Signal Has Too Many Transitions/Events | GO to Pinpoint Test B |
| U3001:68 | Control Module Improper Shutdown Performance: Event Information | GO to Pinpoint Test BD |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test BC |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test BC |
| U3003:68 | Battery Voltage: Event Information | GO to Pinpoint Test BC |