| B10AB:00 |
Remote Keyless Entry Synchronization: No Sub Type Information |
GO to Pinpoint Test I |
| B10C7:01 |
Interior Trunk Antenna: General Electrical Failure |
GO to Pinpoint Test N |
| B1218:00 |
Transmitter Identification Code: No Sub Type Information |
GO to Pinpoint Test I |
| B121A:11 |
Keypad Illumination Output: Circuit Short To Ground |
GO to Pinpoint Test H |
| B121A:15 |
Keypad Illumination Output: Circuit Short To Battery Or Open |
GO to Pinpoint Test H |
| B121B:01 |
Keypad Input Switch: General Electronic Failure |
GO to Pinpoint Test G |
| B12E8:11 |
Liftgate/ Tailgate Control/ Release Switch: Circuit Short To Ground |
GO to Pinpoint Test AL |
| B1336:01 |
Left Front External Antenna: General Electrical Failure |
GO to Pinpoint Test M |
| B1337:01 |
Right Front Door External Antenna: General Electrical Failure |
GO to Pinpoint Test M |
| B14A9:11 |
Liftgate/ Decklid Release Output: Circuit Short To Ground |
GO to Pinpoint Test AL |
| B14A9:15 |
Liftgate/ Decklid Release Open: Circuit Short To Battery |
GO to Pinpoint Test AL |
| B1087:00 |
LIN Bus "A": No Sub Type Information |
GO to Pinpoint Test C |
| B12BA:11 |
Lock Status LED - Front: Circuit Short To Ground |
GO to Pinpoint Test D |
| B12E1:92 |
Front Door Unlock Switch - Interior: Performance or Incorrect Operation |
GO to Pinpoint Test D |
| B12E1:9E |
Front Door Unlock Switch - Interior: Stuck On |
GO to Pinpoint Test D |
| B12E3:92 |
Front Door Switch - Interior: Performance or Incorrect Operation |
GO to Pinpoint Test D |
| B12E3:9E |
Front Door Switch - Interior: Stuck On |
GO to Pinpoint Test D |
| B1519:92 |
Exterior Door Unlatch Switch: Performance or Incorrect Operation |
GO to Pinpoint Test C |
| B1519:9E |
Exterior Door Unlatch Switch: Stuck On |
GO to Pinpoint Test C |
| B151A:92 |
Interior Door Unlatch Switch: Performance or Incorrect Operation |
GO to Pinpoint Test D |
| B151A:9E |
Interior Door Unlatch Switch: Stuck On |
GO to Pinpoint Test D |
| B1588:13 |
Double Lock Output: Circuit Open |
GO to Pinpoint Test F |
| B1588:19 |
Double Lock Output: Circuit Current Above Threshold |
GO to Pinpoint Test F |
| B15F8:09 |
Door Actuation Switch: Component Failure |
GO to Pinpoint Test C |
| B15F9:13 |
Door Presenter Actuator: Circuit Open |
GO to Pinpoint Test E |
| B15F9:19 |
Door Presenter Actuator: Circuit Current Above Threshold |
GO to Pinpoint Test E |
| B15FA:16 |
Double Lock Actuator Sensor: Circuit Current Below Threshold |
GO to Pinpoint Test F |
| B15FA:19 |
Double Lock Actuator Sensor: Circuit Current Above Threshold |
GO to Pinpoint Test F |
| B15FB:16 |
Door Presenter Sensor: Circuit Current Below Threshold |
GO to Pinpoint Test E |
| B15FB:19 |
Door Presenter Sensor: Circuit Current Above Threshold |
GO to Pinpoint Test E |
| U0100:00 |
Lost Communication With ECM/PCM "A": No Sub-Type Information |
GO to Pinpoint Test Q |
| U0140:00 |
Lost Communication With Body Control Module: No Sub-Type Information |
GO to Pinpoint Test R |
| U0151:00 |
Lost Communication With Body Control Module: No Sub-Type Information |
GO to Pinpoint Test S |
| U0452:00 |
Invalid Data Received From Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test Z |
| U1000:00 |
Solid State Driver Protection Active -Driver Disabled: No Sub Type Information |
GO to Pinpoint Test AC |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AA |
| U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test AA |
| U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test AA |
| U3000:01 |
Control Module: General Electrical Failure |
GO to Pinpoint Test AB |
| U3000:11 |
Control Module: Circuit Short To Ground |
GO to Pinpoint Test AB |
| U3000:13 |
Control Module: Circuit Open |
GO to Pinpoint Test AB |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AB |
| U3000:77 |
Control Module: Commanded Position Not Reachable |
GO to Pinpoint Test AB |
| U3000:91 |
Control Module: Parametric |
GO to Pinpoint Test AB |
| B1087:00 |
LIN Bus "A": No Sub Type Information |
GO to Pinpoint Test C |
| B12BA:11 |
Lock Status LED - Front: Circuit Short To Ground |
GO to Pinpoint Test D |
| B12E1:92 |
Front Door Unlock Switch - Interior: Performance or Incorrect Operation |
GO to Pinpoint Test D |
| B12E1:9E |
Front Door Lock Switch - Interior: Stuck On |
GO to Pinpoint Test D |
| B12E3:92 |
Front Door Lock Switch - Interior: Performance or Incorrect Operation |
GO to Pinpoint Test D |
| B12E3:9E |
Front Door Lock Switch - Interior: Stuck On |
GO to Pinpoint Test D |
| B1519:92 |
Exterior Door Unlatch Switch: Performance or Incorrect Operation |
GO to Pinpoint Test C |
| B1519:9E |
Exterior Door Unlatch Switch: Stuck On |
GO to Pinpoint Test C |
| B151A:92 |
Interior Door Unlatch Switch: Performance or Incorrect Operation |
GO to Pinpoint Test D |
| B151A:9E |
Interior Door Unlatch Switch: Stuck On |
GO to Pinpoint Test D |
| B1588:13 |
Double Lock Output: Circuit Open |
GO to Pinpoint Test F |
| B1588:19 |
Double Lock Output: Circuit Current Above Threshold |
GO to Pinpoint Test F |
| B15F8:09 |
Door Latch Actuation Switch: Component Failure |
GO to Pinpoint Test C |
| B15F9:13 |
Door Presenter Actuator: Circuit Open |
GO to Pinpoint Test E |
| B15F9:19 |
Door PresenterActuator: Circuit Current Above Threshold |
GO to Pinpoint Test E |
| B15FA:16 |
Double Lock Actuator Sensor: Circuit Current Below Threshold |
GO to Pinpoint Test F |
| B15FA:19 |
Double Lock Actuator Sensor: Circuit Current Above Threshold |
GO to Pinpoint Test F |
| B15FB:16 |
Door Presenter Sensor: Circuit Current Below Threshold |
GO to Pinpoint Test E |
| B15FB:19 |
Door Presenter Sensor: Circuit Current Above Threshold |
GO to Pinpoint Test E |
| U0100:00 |
Lost Communication With ECM/PCM "A": No Sub-Type Information |
GO to Pinpoint Test Q |
| U0140:00 |
Lost Communication With Body Control Module: No Sub-Type Information |
GO to Pinpoint Test R |
| U0151:00 |
Lost Communication With Body Control Module: No Sub-Type Information |
GO to Pinpoint Test S |
| U0452:00 |
Invalid Data Received From Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test Z |
| U1000:00 |
Solid State Driver Protection Active -Driver Disabled: No Sub Type Information |
GO to Pinpoint Test AC |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AA |
| U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test AA |
| U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test AA |
| U3000:01 |
Control Module: General Electrical Failure |
GO to Pinpoint Test AB |
| U3000:11 |
Control Module: Circuit Short To Ground |
GO to Pinpoint Test AB |
| U3000:13 |
Control Module: Circuit Open |
GO to Pinpoint Test AB |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AB |
| U3000:77 |
Control Module: Commanded Position Not Reachable |
GO to Pinpoint Test AB |
| U3000:91 |
Control Module: Parametric |
GO to Pinpoint Test AB |
| B1087:00 |
LIN Bus "A": No Sub Type Information |
GO to Pinpoint Test C |
| B1519:92 |
Exterior Door Unlatch Switch: Performance or Incorrect Operation |
GO to Pinpoint Test C |
| B1519:9E |
Exterior Door Unlatch Switch: Stuck On |
GO to Pinpoint Test C |
| B15F8:09 |
Door Actuation Switch: Component Failure |
GO to Pinpoint Test C |
| B15F9:13 |
Door Presenter Actuator: Circuit Open |
GO to Pinpoint Test E |
| B15F9:19 |
Door Presenter Actuator: Circuit Current Above Threshold |
GO to Pinpoint Test E |
| B15FB:16 |
Door Presenter Sensor: Circuit Current Below Threshold |
GO to Pinpoint Test E |
| B15FB:19 |
Door Presenter Sensor: Circuit Current Above Threshold |
GO to Pinpoint Test E |
| U0100:00 |
Lost Communication With ECM/PCM "A": No Sub-Type Information |
GO to Pinpoint Test Q |
| U0140:00 |
Lost Communication With Body Control Module: No Sub-Type Information |
GO to Pinpoint Test R |
| U0151:00 |
Lost Communication With Body Control Module: No Sub-Type Information |
GO to Pinpoint Test S |
| U0452:00 |
Invalid Data Received From Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test Z |
| U1000:00 |
Solid State Driver Protection Active -Driver Disabled: No Sub Type Information |
GO to Pinpoint Test AC |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AA |
| U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test AA |
| U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test AA |
| U3000:01 |
Control Module: General Electrical Failure |
GO to Pinpoint Test AB |
| U3000:11 |
Control Module: Circuit Short To Ground |
GO to Pinpoint Test AB |
| U3000:13 |
Control Module: Circuit Open |
GO to Pinpoint Test AB |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AB |
| U3000:77 |
Control Module: Commanded Position Not Reachable |
GO to Pinpoint Test AB |
| U3000:91 |
Control Module: Parametric |
GO to Pinpoint Test AB |
| B1087:00 |
LIN Bus "A": No Sub Type Information |
GO to Pinpoint Test C |
| B1519:92 |
Exterior Door Unlatch Switch: Performance or Incorrect Operation |
GO to Pinpoint Test C |
| B1519:9E |
Exterior Door Unlatch Switch: Stuck On |
GO to Pinpoint Test C |
| B15F8:09 |
Door Actuation Switch: Component Failure |
GO to Pinpoint Test C |
| B15F9:13 |
Door Presenter Actuator: Circuit Open |
GO to Pinpoint Test E |
| B15F9:19 |
Door Presenter Actuator: Circuit Current Above Threshold |
GO to Pinpoint Test E |
| B15FB:16 |
Door Presenter Sensor: Circuit Current Below Threshold |
GO to Pinpoint Test E |
| B15FB:19 |
Door Presenter Sensor: Circuit Current Above Threshold |
GO to Pinpoint Test E |
| U0100:00 |
Lost Communication With ECM/PCM "A": No Sub-Type Information |
GO to Pinpoint Test Q |
| U0140:00 |
Lost Communication With Body Control Module: No Sub-Type Information |
GO to Pinpoint Test R |
| U0151:00 |
Lost Communication With Body Control Module: No Sub-Type Information |
GO to Pinpoint Test S |
| U0452:00 |
Invalid Data Received From Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test Z |
| U1000:00 |
Solid State Driver Protection Active -Driver Disabled: No Sub Type Information |
GO to Pinpoint Test AC |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AA |
| U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test AA |
| U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test AA |
| U3000:01 |
Control Module: General Electrical Failure |
GO to Pinpoint Test AB |
| U3000:11 |
Control Module: Circuit Short To Ground |
GO to Pinpoint Test AB |
| U3000:13 |
Control Module: Circuit Open |
GO to Pinpoint Test AB |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AB |
| U3000:77 |
Control Module: Commanded Position Not Reachable |
GO to Pinpoint Test AB |
| U3000:91 |
Control Module: Parametric |
GO to Pinpoint Test AB |
| B1142:29 |
Ignition Status 1: Signal Invalid |
GO to Pinpoint Test P |
| U0140:00 |
Lost Communication With Body Control Module: No Sub-Type Information |
GO to Pinpoint Test R |
| U0164:00 |
Lost Communication With HVAC Control Module: No Sub-Type Information |
GO to Pinpoint Test T |
| U0208:00 |
Lost Communication With "Seat Control Module A": No Sub-Type Information |
GO to Pinpoint Test U |
| U0232:00 |
Lost Communication With Side Obstacle Detection Control Module "A": No Sub-Type Information |
GO to Pinpoint Test V |
| U0294:00 |
Lost Communication With Powertrain Control Monitor Module: No Sub-Type Information |
GO to Pinpoint Test W |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test Z |
| U0509:00 |
Invalid Data Received From "Seat Control Module A": No Sub Type Information |
GO to Pinpoint Test Z |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AA |
| U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test AA |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AB |
| U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to Pinpoint Test X |
| U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test Y |
| B1219:23 |
Interior Boot/Trunk Release Switch: Signal Stuck Low |
GO to Pinpoint Test AD |
| B1452:11 |
Tailgate/Liftgate/Boot/Trunk Latch Release Actuator: Circuit Short To Ground |
GO to Pinpoint Test AE |
| B1452:13 |
Tailgate/Liftgate/Boot/Trunk Latch Release Actuator: Circuit Open |
GO to Pinpoint Test AE |
| B1452:4B |
Tailgate/Liftgate/Boot/Trunk Latch Release Actuator: Over Temperature |
GO to Pinpoint Test AE |
| B1452:98 |
Tailgate/Liftgate/Boot/Trunk Latch Release Actuator: Component or System Over Temperature |
GO to Pinpoint Test AE |
| B15DE:11 |
Tailgate/Liftgate/Boot/Trunk Latch Release Return: Circuit Short To Ground |
GO to Pinpoint Test AE |
| B15DE:13 |
Tailgate/Liftgate/Boot/Trunk Latch Release Return: Circuit Open |
GO to Pinpoint Test AE |
| B161F:11 |
Front Trunk Relay Coil Power: Circuit Short To Ground |
GO to Pinpoint Test AE |
| B161F:13 |
Front Trunk Relay Coil Power: Circuit Open |
GO to Pinpoint Test AE |
| B1620:11 |
Front Trunk Relay Coil SET: Circuit Short To Ground |
GO to Pinpoint Test AE |
| B1621:11 |
Front Trunk Relay Coil RESET: Circuit Short To Ground |
GO to Pinpoint Test AE |
| U0010:00 |
Medium Speed CAN Communication Bus: No Sub Type Information |
GO to Pinpoint Test AG |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test AH |
| U0300:00 |
Internal Control Module Software Incompatibility: No Sub Type Information |
GO to Pinpoint Test AI |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test AH |
| U0594:00 |
Invalid Data Received from Hybrid/EV Powertrain Control Module: No Sub Type Information |
GO to Pinpoint Test AK |
| U201A:57 |
Control Module Main Calibration Data: Invalid / Incompatible Software Component |
GO to Pinpoint Test AI |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AI |
| U3000:04 |
Control Module: System Internal Failure |
GO to Pinpoint Test AJ |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AJ |
| B1142:29 |
Ignition Status 1: Signal Invalid |
GO to Pinpoint Test P |
| U0140:00 |
Lost Communication With Body Control Module: No Sub-Type Information |
GO to Pinpoint Test R |
| U0164:00 |
Lost Communication With HVAC Control Module: No Sub-Type Information |
GO to Pinpoint Test T |
| U0208:00 |
Lost Communication With "Seat Control Module A": No Sub-Type Information |
GO to Pinpoint Test U |
| U0294:00 |
Lost Communication With Powertrain Control Monitor Module: No Sub-Type Information |
GO to Pinpoint Test W |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test Z |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AA |
| U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test AA |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AB |
| U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to Pinpoint Test X |
| U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test Y |
| P1594:00 |
Forced Engine Shutdown - Remote Start System Fault, No Unattended Vehicle Timeout: No Fault Type Information |
GO to Pinpoint Test O |
| P1595:00 |
Forced Engine Shutdown - Remote Start System Fault, Transmission Range Not In Park Position: No Fault Type Information |
GO to Pinpoint Test O |