Common Specifications & Procedures
ESCAPE COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | Specifications | ||
| Torque | Refer to appropriate procedure(s) in Removal And Installation . | ||
| Axle Nut/Hub Nut Stage 1: 81 lb.ft (110 Nm) |
|||
| Battery | Specifications | ||
| Brakes | |||
| Bleeding Sequence | RR, LR, RF, LF Brake System Pressure Bleeding |
||
| Disc Brakes w/Torque | |||
| Front Disc | Refer to approriate component in Removal And Installation procedures. | ||
| Rear Disc | Refer to approriate component in Removal And Installation procedures | ||
| Charging | |||
| Generator w/Torque | For Removal and Installation Refer to Removal And Installation 1.5L EcoBoost: Upper/Lower Generator Bolt: 18 lb.ft (25 Nm) Generator Nut: 18 lb.ft (25 Nm) 2.0L EcoBoost/2.5L Duratec: Upp/Lower Generator Bolt: Torque: 18 lb.ft (25 Nm) Generator B+ Wire Nut: Torque: 150 lb.in (17 Nm) |
||
| Drive Belts | |||
| Adjustment | For Accessory Drive Belt adjustment, refer to: Accessory Drive Belt - Vehicles Built Up To: 01-October-2020 / Accessory Drive Belt - Vehicles Built From: 02-October-2020 (1.5L) or Accessory Drive Belt (2.0L) | ||
| Belt Routing | |||
| 1.5L | Accessory Drive - Component Location | ||
| 2.0L | Accessory Drive - Component Location | ||
| Engine Cooling | |||
| General Service Specifications | Specifications (1.5L) or Specifications (2.0L) or Specifications (2.5L) | ||
| Radiator Pressure Cap | |||
| 1.5L | 17.4-21.7 psi (120-150 kPa) | ||
| 2.0L; 2.5L | 17.4-21.7 psi (120-150 kPa) | ||
| Thermostat R & I | |||
| 1.5L | Thermostat Housing | ||
| 2.0L | Thermostat Housing | ||
| 2.5L | Thermostat Housing | ||
| Water Pump R & I | |||
| 1.5L | Coolant Pump | ||
| 2.0L | Coolant Pump | ||
| 2.5L | Coolant Pump | ||
| Engine Mechanical | |||
| 1.5L | |||
| Compression | Specifications | ||
| Oil Pressure (hot @ 800 RPM) | 15.2 psi (1.05 bar) | ||
| Oil Pressure (hot @ 2, 000 RPM) | 40.6 psi (2.8 bar) | ||
| Overhaul | Specifications | ||
| Torque | Refer to appropriate component procedure(s) in Removal And Installation . | ||
| 2.0L | |||
| Compression | Specifications | ||
| Oil Pressure @ 1, 500 rpm | 27.6 -37.7 psi (190 -260 kPa) | ||
| Overhaul | Specifications | ||
| Torque | Refer to appropriate component procedure(s) in Removal And Installation | ||
| 2.5L | |||
| Compression | Specifications | ||
| Oil pressure (hot @ 2000 rpm) | 29-60 psi (200-414 kPa) | ||
| Overhaul | Specifications | ||
| Torque | Refer to appropriate component procedure(s) in Removal And Installation procedures. | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate Torque | |||
| 1.5L | Refer to Flexplate
for sequence. Stage 1: 89 lb.in (10 Nm) Stage 2: 177 lb.in (20 Nm) Stage 3: 22 lb.ft (30 Nm) Stage 4: 90° |
||
| 2.0L | Refer to Flexplate
for sequence Stage 1: 37 Ft. Lbs. (50 N.m) Stage 2: 59 Ft. Lbs. (80 N.m) Stage 3: 83 Ft. Lbs. (112 N.m) |
||
| 2.5L | Refer to Flywheel
for sequence. Stage 1: 37 Ft. Lbs. (50 N.m) Stage 2: 59 Ft. Lbs. (80 N.m) Stage 3: 83 Ft. Lbs. (112 N.m) |
||
| Fuel System | |||
| Fuel Filter Location | Lifetime fuel filter (serviced as part of the Fuel Pump module). | ||
| Fuel Filter R & I | Fuel Pump And Sender Unit (1.5L) or Fuel Pump And Sender Unit (2.0L) or Fuel Pump And Sender Unit (2.5L). | ||
| Pressure Release Procedure | Fuel System Pressure Release (1.5L) or Fuel System Pressure Release (2.0L) or Fuel System Pressure Release (2.5). | ||
| Pressure Specification | Specifications (1.5L) or Specifications (2.0L) or Specifications (2.5L) | ||
| Fuel Pressure Test Procedure | Fuel System Pressure Check (1.5L) or Fuel System Pressure Check (2.0L) or Fuel System Pressure Check (2.5L). | ||
| Ignition | |||
| Firing Order & Cylinder Identification | Firing Order & Cylinder Identification | ||
| Spark Plugs | |||
| 1.5L | |||
| Number | HYFS 094 YEC | ||
| Gap | .7 mm (0.028 in) | ||
| Torque | 115 lb.in (13 Nm) | ||
| 2.0L | |||
| Number | CYFS 12Y PCT | ||
| Gap | .030 in (.75mm) | ||
| Torque | 106 In. Lbs. (12 N.m) | ||
| 2.5L | |||
| Number | AYFS 32Y R | ||
| Gap | 0.049 in (1.25 mm) to 0.053 in (1.35 mm) | ||
| Torque | 106 In. Lbs. (12 N.m) | ||
| Starting | |||
| Starter w/Torque | |||
| 1.5L | 35 lb.ft (48 Nm) | ||
| 2.0L | 35 lb.ft (48 Nm) | ||
| 2.5L | 35 lb.ft (48 Nm) | ||
| Wheel Alignment | |||
| Adjustment Specifications | Specifications | ||
| Torque | Refer to the appropriate procedure in General Procedures | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque For Tightening Sequence Refer to Wheel And Tire |
100 lb.ft (135 Nm) | ||