2.3L EcoBoost (231kW/314PS)
DTC INDEX
| DTC | Description | Warning Light/DTC Type | Action |
|---|---|---|---|
| P0657 | Actuator Supply Voltage "A" Circuit Open | MIL, Wrench/Continuous | If the power circuit to the transmission solenoids is interrupted then all solenoids are failed electrically off. CHECK for an open, short to ground or the transmission connector disconnected. REPAIR as required. CLEAR the DTC. GO to Pinpoint Test A |
| P0702 | Transmission Control System Electrical | Wrench/Continuous | INSPECT the PCM power and ground circuits for opens or short to ground. INSPECT the PCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. RERUN the KOEO and KOER self-test. If DTC P0702 returns, REFER to: Charging System - 2.3L EcoBoost (231kW/314PS) . |
| P0706 | Transmission Range Sensor "A" Circuit Range/Performance | Wrench/KOEO, Continuous | The TR sensor outputs a duty cycle indicating manual lever position. This DTC sets when the frequency is greater or less than the expected duty cycle by 25Hz or more. Engine may not crank. CLEAR the DTC. If DTC P0706 returns, GO to Pinpoint Test C |
| P0707 | Transmission Range Sensor "A" Circuit Low | Wrench/KOEO, Continuous | Engine may not crank, CLEAR the DTC. If DTC P0707 returns, GO to Pinpoint Test C |
| P0708 | Transmission Range Sensor "A" Circuit High | Wrench/KOEO, Continuous | Engine may not crank, CLEAR the DTC. If DTC P0708 returns, GO to Pinpoint Test C |
| P0709 | Transmission Range Sensor "A" Circuit Intermittent | Wrench/Continuous | The TR sensor outputs a duty cycle indicating manual lever position. This DTC sets when the duty cycle is within range but is in the dead band between the design position, and an in-range but invalid duty cycle. GO to Pinpoint Test C |
| P0710 | Transmission Fluid Temperature Sensor "A" Circuit | Wrench/Continuous | CLEAR the DTC. If DTC P0710 returns, GO to Pinpoint Test B |
| P0711 | Transmission Fluid Temperature Sensor "A" Circuit Range/Performance | MIL/Continuous | CLEAR the DTC. Road test the vehicle at least 5 minutes. If DTC P0711 returns, GO to Pinpoint Test B |
| P0712 | Transmission Fluid Temperature Sensor "A" Circuit Low | MIL/KOEO, Continuous | DTC P0710 may set. CLEAR the DTC. If DTC P0712 returns, GO to Pinpoint Test B |
| P0713 | Transmission Fluid Temperature Sensor "A" Circuit High | MIL/KOEO, Continuous | DTC P0710 may set. CLEAR the DTC. If DTC P0713 returns, GO to Pinpoint Test B |
| P0715 | TSS Sensor "A" Circuit | MIL/KOEO, Continuous | CLEAR DTC. If DTC P0715 returns during KOEO, GO to Pinpoint Test D |
| P0716 | TSS Sensor "A" Circuit Range/Performance | MIL/Continuous | The TCM detected TSS sensor drop out, noise spike, or TSS speed not corresponding to other speed sensor inputs for current gear. GO to Pinpoint Test F |
| P0717 | TSS Sensor "A" Circuit No Signal | Wrench/Continuous | P0717 illuminates the wrench light in conjunction with P0715, P07BF, and/or P07C0. Service the more specific DTC first. GO to Pinpoint Test D |
| P0718 | TSS Sensor "A" Circuit Intermittent | MIL/Continuous | The PCM detected TSS sensor fault, but the fault did not last long enough for the PCM to set a more specific TSS sensor DTC. Inspect TSS sensor wiring and connectors for damage. |
| P0720 | Output Shaft Speed Sensor Circuit | MIL/KOEO, Continuous | CLEAR the DTC. If DTC P0720 returns during KOEO, GO to Pinpoint Test D |
| P0721 | Output Shaft Speed Sensor Circuit Range/Performance | MIL/Continuous | The TCM detected OSS sensor drop out, noise spike, or OSS speed not corresponding to other speed sensor inputs for current gear. GO to Pinpoint Test F |
| P0722 | Output Shaft Speed Sensor Circuit No Signal | Wrench/Continuous | DTC P0722 illuminates the wrench light in conjunction with P0720, P077C, and/or P077D. Service the more specific DTC first. GO to Pinpoint Test D |
| P0723 | Output Shaft Speed Sensor Circuit Intermittent | MIL/Continuous | The PCM detected OSS sensor fault, but the fault did not last long enough for the PCM to set a more specific OSS sensor DTC. Inspect OSS sensor wiring and connectors for damage. |
| P0729 | Gear 6 Incorrect Ratio | Wrench/Continuous | The PCM detected multiple ratio errors either in or while shifting to 6th gear. The ratio error did not last long enough for the PCM to isolate the fault to a specific clutch. REFER to: Diagnosis By Symptom . |
| P0731 | Gear 1 Incorrect Ratio | Wrench/Continuous | The PCM detected multiple ratio error either in or while shifting to 1st gear. The ratio error did not last long enough for the PCM to isolate the fault to a specific clutch. REFER to: Diagnosis By Symptom . |
| P0732 | Gear 2 Incorrect Ratio | Wrench/Continuous | The PCM detected multiple ratio error either in or while shifting to 2nd gear. The ratio error did not last long enough for the PCM to isolate the fault to a specific clutch. REFER to: Diagnosis By Symptom . |
| P0733 | Gear 3 Incorrect Ratio | Wrench/Continuous | The PCM detected multiple ratio error either in or while shifting to 3rd gear. The ratio error did not last long enough for the PCM to isolate the fault to a specific clutch. REFER to: Diagnosis By Symptom . |
| P0734 | Gear 4 Incorrect Ratio | Wrench/Continuous | The PCM detected multiple ratio errors either in or while shifting to 4th gear. The ratio error did not last long enough for the PCM to isolate the fault to a specific clutch. REFER to: Diagnosis By Symptom . |
| P0735 | Gear 5 Incorrect Ratio | Wrench/Continuous | The PCM detected multiple ratio errors either in or while shifting to 5th gear. The ratio error did not last long enough for the PCM to isolate the fault to a specific clutch. REFER to: Diagnosis By Symptom . |
| P0736 | Reverse Incorrect Ratio | Wrench/Continuous | The PCM detected multiple ratio error either in or while shifting to Reverse. The ratio error did not last long enough for the PCM to isolate the fault to a specific clutch. REFER to: Diagnosis By Symptom . |
| P0740 | Torque Converter Clutch Solenoid Circuit/Open | Wrench/KOEO, Continuous | CLEAR DTC. If DTC P0740 returns during KOER, GO to Pinpoint Test E |
| P0741 | Torque Converter Clutch Solenoid Circuit Performance/Stuck Off | Wrench/Continuous | DTC P0741 is a non-electrical failure that caused the TCC to fail to apply. For TCC Does Not Apply Symptom, REFER to: Torque Converter Clutch (TCC) . |
| P0743 | Torque Converter Clutch Solenoid Circuit Electrical | Wrench/KOEO, Continuous | DTC P0743 illuminates the wrench light in conjunction with P0740, P2769, and/or P2770. Service the more specific DTC first. GO to Pinpoint Test E |
| P0748 | Pressure Control Solenoid Electrical | Wrench/KOEO, Continuous | DTC P0748 illuminates the wrench light in conjunction with P0960, P0962, and/or P0963. Service the more specific DTC first. GO to Pinpoint Test E |
| P0751 | Shift Solenoid "A" Performance/Stuck Off | MIL/KOEO, Continuous | DTC P0751 is a non-electrical failure indicating the A clutch failed to apply. For A clutch Does Not Apply symptom, REFER to: A Clutch . |
| P0752 | Shift Solenoid "A" Stuck On | MIL/Continuous | DTC P0752 is a non-electrical failure indicating the A clutch stayed applied when SSA was de-energized. For A clutch Always Applied symptom, REFER to: A Clutch . |
| P0753 | Shift Solenoid "A" Electrical | Wrench/KOEO, Continuous | DTC P0753 illuminates the wrench light in conjunction with P0973, P0974, and/or P097A. Service the more specific DTC first. GO to Pinpoint Test A |
| P0754 | Shift Solenoid "A" Intermittent | MIL/Continuous | The PCM detected a SSA fault, but the fault did not last long enough for the PCM to set a more specific SSA DTC. Inspect SSA wiring and connectors for damage. |
| P0756 | Shift Solenoid "B" Performance/Stuck Off | MIL/Continuous | DTC P0756 is a non-electrical failure indicating the B clutch failed to apply. For B clutch Does Not Apply symptom, REFER to: B Clutch . |
| P0757 | Shift Solenoid "B" Stuck On | MIL/Continuous | DTC P0757 is a non-electrical failure indicating B clutch stayed applied when SSB was de-energized. For B clutch Always Applied symptom, REFER to: B Clutch . |
| P0758 | Shift Solenoid "B" Electrical | Wrench, KOEO, Continuous | DTC P0758 illuminates the wrench light in conjunction with P0976, P0977, and/or P097B. Service the more specific DTC first. GO to Pinpoint Test A |
| P0759 | Shift Solenoid "B" Intermittent | MIL/Continuous | The PCM detected SSB fault, but the fault did not last long enough for the PCM to set a more specific SSB DTC. Inspect SSB wiring and connectors for damage. |
| P0761 | Shift Solenoid "C" Performance/Stuck Off | MIL/Continuous | DTC P0761 is a non-electrical failure indicating the C clutch failed to apply. For C clutch Does Not Apply symptom, REFER to: C Clutch . |
| P0762 | Shift Solenoid "C" Stuck On | MIL/Continuous | DTC P0762 is a non-electrical failure indicating the C clutch stayed applied when SSC was de-energized. For C clutch Always Applied symptom, REFER to: C Clutch . |
| P0763 | Shift Solenoid "C" Electrical | Wrench, KOEO, Continuous | DTC P0763 illuminates the wrench light in conjunction with P0779, P097C, and/or P0980. Service the more specific DTC first. GO to Pinpoint Test A |
| P0764 | Shift Solenoid "C" Intermittent | MIL/Continuous | The PCM detected SSC fault, but the fault did not last long enough for the PCM to set a more specific SSC DTC. Inspect SSC wiring and connectors for damage. |
| P0766 | Shift Solenoid "D" Performance/Stuck Off | MIL/Continuous | DTC P0761 is a non-electrical failure indicating D clutch failed to apply. For D clutch Does Not Apply symptom, REFER to: D Clutch . |
| P0767 | Shift Solenoid "D" Stuck On | MIL/Continuous | DTC P0757 is a non-electrical failure indicating the D clutch stayed applied when SSD was de-energized. For D clutch Always Applied symptom, REFER to: D Clutch . |
| P0768 | Shift Solenoid "D" Electrical | Wrench, KOEO, Continuous | DTC P0768 illuminates the wrench light in conjunction with P097D, P0982, P0982 illuminates the Wrench light. Service the more specific DTC first. GO to Pinpoint Test A |
| P0769 | Shift Solenoid "D" Intermittent | MIL/Continuous | The PCM detected SSD fault, but the fault did not last long enough for the PCM to set a more specific SSD DTC. Inspect SSD wiring and connectors for damage. |
| P076F | Gear 7 Incorrect Ratio | Wrench/Continuous | The PCM detected multiple ratio error either in or while shifting to 7th gear. The ratio error did not last long enough for the PCM to isolate the fault to a specific clutch. REFER to: Diagnosis By Symptom . |
| P0771 | Shift Solenoid "E" Performance/Stuck Off | MIL/Continuous | DTC P0761 is a non-electrical failure indicating the E clutch failed to apply. For E clutch Does Not Apply symptom, REFER to: E Clutch . |
| P0772 | Shift Solenoid "E" Stuck On | MIL/Continuous | DTC P0772 is a non-electrical failure indicating the E clutch stayed applied when SSE was de-energized. For E clutch Always Applied symptom, REFER to: E Clutch . |
| P0773 | Shift Solenoid "E" Electrical | Wrench/Continuous | DTC P0773 illuminates the wrench light in conjunction with P097E, P0985, P0986. Service the more specific DTC first. GO to Pinpoint Test A |
| P0774 | Shift Solenoid "E" Intermittent | MIL/Continuous | The PCM detected SSE fault, but the fault did not last long enough for the PCM to set a more specific SSE DTC. Inspect SSE wiring and connectors for damage. |
| P077D | Output Shaft Speed Sensor Circuit High | MIL/KOEO, Continuous | GO to Pinpoint Test D |
| P0791 | Intermediate Shaft Speed Sensor "A" Circuit | MIL/Continuous | GO to Pinpoint Test D |
| P0792 | Intermediate Shaft Speed Sensor "A" Circuit Range/Performance | MIL/Continuous | GO to Pinpoint Test F |
| P0793 | Intermediate Shaft Speed Sensor "A" Circuit No Signal | Wrench | GO to Pinpoint Test D |
| P0794 | Intermediate Shaft Speed Sensor "A" Circuit Intermittent | MIL/Continuous | GO to Pinpoint Test D |
| P07A9 | Transmission Friction Element "D" Stuck On | None/Continuous | The PCM detected that D clutch failed to release multiple times and determined the SSD is not stuck on. For D clutch Always Applied symptom, REFER to: D Clutch . |
| P07AB | Transmission Friction Element "E" Stuck On | None/Continuous | The PCM detected that E clutch failed to release multiple times and determined the SSE is not stuck on. For E clutch Always Applied symptom, REFER to: E Clutch . |
| P07AD | Transmission Friction Element "F" Stuck On | None/Continuous | The PCM detected that F clutch failed to release multiple times and determined the SSF is not stuck on. For F clutch Always Applied symptom, REFER to: F Clutch . |
| P07C0 | TSS Sensor "A" Circuit High | MIL/KOEO, Continuous | GO to Pinpoint Test D |
| P07C6 | Intermediate Shaft Speed Sensor "A" Circuit High | MIL/Continuous | GO to Pinpoint Test D |
| P07C8 | Intermediate Shaft Speed Sensor "B" Circuit High | MIL/KOEO, Continuous | GO to Pinpoint Test D |
| P07D9 | Gear 8 Incorrect Ratio | Wrench/Continuous | The PCM detected multiple ratio error either in or while shifting to 8th gear. The ratio error did not last long enough for the PCM to isolate the fault to a specific clutch. REFER to: Diagnosis By Symptom . |
| P07F6 | Gear 9 Incorrect Ratio | Wrench/Continuous | The PCM detected multiple ratio error either in or while shifting to 9th gear. The ratio error did not last long enough for the PCM to isolate the fault to a specific clutch. REFER to: Diagnosis By Symptom . |
| P07F7 | Gear 10 Incorrect Ratio | Wrench/Continuous | The PCM detected multiple ratio error either in or while shifting to 10th gear. The ratio error did not last long enough for the PCM to isolate the fault to a specific clutch. REFER to: Diagnosis By Symptom . |
| P0868 | Transmission Fluid Pressure Low | Wrench/Continuous | CLEAR the DTC. Road test vehicle, if DTC P0868 returns, or if DTCs P0751, P0756, P0761, P0766, P0771 or P2707 are set, TEST for low pump pressure or fluid contamination. PERFORM the line pressure test. REFER to: Special Testing Procedures . |
| P0882 | TCM Power Input Signal Low | MIL/KOEO, Continuous | INSPECT the PCM power and ground circuits for opens or short to ground. INSPECT the PCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. If DTC P0882 returns, REFER to: Charging System - 2.3L EcoBoost (231kW/314PS) . |
| P0883 | TCM Power Input Signal High | MIL/KOEO, Continuous | CLEAR the DTC. If DTC P0883 returns, REFER to: Charging System - 2.3L EcoBoost (231kW/314PS) . |
| P0960 | Pressure Control Solenoid Control Circuit/Open | MIL/KOEO, Continuous | The LPC solenoid failed to max pressure indicating wiring or connector --issues, or a solenoid electrical issue. INSPECT the LPC solenoid wiring, connectors and pins. GO to Pinpoint Test E |
| P0961 | Pressure Control Solenoid Control Circuit Range/Performance | MIL/Continuous | The LPC solenoid failed to max pressure indicating wiring or connector issues, or a solenoid electrical issue. INSPECT the LPC solenoid wiring, connectors and pins. GO to Pinpoint Test E |
| P0962 | Pressure Control Solenoid Control Circuit Low | MIL/KOEO, Continuous | The LPC solenoid failed to max pressure indicating wiring or connector issues, or a solenoid electrical issue. INSPECT the LPC solenoid wiring, connectors and pins. GO to Pinpoint Test E |
| P0963 | Pressure Control Solenoid Control Circuit High | MIL/KOEO, Continuous | The LPC solenoid failed to high current which is maximum pressure indicating short to ground, wiring or solenoid issue. INSPECT the LPC solenoid wiring, connectors and pins. GO to Pinpoint Test E |
| P0973 | Shift Solenoid "A" Control Circuit Low | MIL/KOEO, Continuous | This DTC indicates a short to ground in the SSA electrical. Since SSA shorted to ground causes SSA to be failed to high current (maximum pressure since SSA is directly proportional). A clutch is failed on. GO to Pinpoint Test A |
| P0974 | Shift Solenoid "A" Control Circuit High | MIL/KOEO, Continuous | This DTC indicates a short to power in the SSA electrical. Since SSA shorted to power causes SSA to be failed to low current (minimum pressure since SSA is directly proportional). A clutch is failed off. GO to Pinpoint Test A |
| P0976 | Shift Solenoid "B" Control Circuit Low | MIL/KOEO, Continuous | This DTC indicates a short to ground in the SSB electrical. Since SSB shorted to ground causes SSB to be failed to high current (maximum pressure since SSB is directly proportional). B clutch is failed on. GO to Pinpoint Test A |
| P0977 | Shift Solenoid "B" Control Circuit High | MIL/KOEO, Continuous | This DTC indicates a short to power in the SSB electrical. Since SSB shorted to power causes SSB to be failed to low current (minimum pressure since SSB is directly proportional). B clutch is failed off. GO to Pinpoint Test A |
| P0979 | Shift Solenoid "C" Control Circuit Low | MIL/KOEO, Continuous | This DTC indicates a short to ground in the SSC electrical. Since SSC shorted to ground causes SSC to be failed to high current (maximum pressure since SSC is directly proportional). C clutch is failed on. GO to Pinpoint Test A |
| P097A | Shift Solenoid "A" Control Circuit/Open | MIL/KOEO, Continuous | This DTC indicates a short to power in the SSA electrical. Since SSA shorted to power causes SSA to be failed to low current (minimum pressure since SSA is directly proportional). A clutch is failed off. GO to Pinpoint Test A |
| P097B | Shift Solenoid "B" Control Circuit/Open | MIL/KOEO, Continuous | This DTC indicates an open circuit in the SSB electrical. Since SSB shorted to power causes SSB to be failed to low current (minimum pressure since SSB is directly proportional). B clutch is failed off. GO to Pinpoint Test A |
| P097C | Shift Solenoid "C" Control Circuit/Open | MIL/KOEO, Continuous | This DTC indicates a short to power in the SSC electrical. Since SSC shorted to power causes SSC to be failed to low current (minimum pressure since SSC is directly proportional). C clutch is failed off. GO to Pinpoint Test A |
| P097D | Shift Solenoid "D" Control Circuit/Open | MIL/KOEO, Continuous | This DTC indicates a short to power in the SSD electrical. Since SSD shorted to power causes SSD to be failed to low current (minimum pressure since SSD is directly proportional). D clutch is failed off. GO to Pinpoint Test A |
| P097E | Shift Solenoid "E" Control Circuit/Open | MIL/KOEO, Continuous | This DTC indicates a short to power in the SSE electrical. Since SSE shorted to power causes SSE to be failed to low current (minimum pressure since SSE is directly proportional). E clutch is failed off. GO to Pinpoint Test A |
| P097F | Shift Solenoid "F" Control Circuit/Open | MIL/KOEO, Continuous | This DTC indicates a short to power in the SSF electrical. Since SSF shorted to power causes SSF to be failed to low current (minimum pressure since SSF is directly proportional). F clutch is failed off. GO to Pinpoint Test A |
| P0980 | Shift Solenoid "C" Control Circuit High | MIL/KOEO, Continuous | This DTC indicates a short to power in the SSC electrical. Since SSC shorted to power causes SSC to be failed to low current (minimum pressure since SSC is directly proportional). C clutch is failed off. GO to Pinpoint Test A |
| P0982 | Shift Solenoid "D" Control Circuit Low | MIL/KOEO, Continuous | This DTC indicates a short to ground in the SSD electrical. Since SSD shorted to ground causes SSD to be failed to high current (maximum pressure since SSD is directly proportional). D clutch is failed on. GO to Pinpoint Test A |
| P0983 | Shift Solenoid "D" Control Circuit High | MIL/KOEO, Continuous | This DTC indicates a short to power in the SSD electrical. Since SSD shorted to power causes SSD to be failed to low current (minimum pressure since SSD is directly proportional). D clutch is failed off. GO to Pinpoint Test A |
| P0985 | Shift Solenoid "E" Control Circuit Low | MIL/KOEO, Continuous | This DTC indicates a short to ground in the SSE electrical. Since SSE shorted to ground causes SSE to be failed to high current (maximum pressure since SSE is directly proportional). E clutch is failed on. GO to Pinpoint Test A |
| P0986 | Shift Solenoid "E" Control Circuit High | MIL/KOEO, Continuous | This DTC indicates a short to power in the SSE electrical. Since SSE shorted to power causes SSE to be failed to low current (minimum pressure since SSE is directly proportional). E clutch is failed off. GO to Pinpoint Test A |
| P0998 | Shift Solenoid "F" Control Circuit Low | MIL/KOEO, Continuous | This DTC indicates a short to ground in the SSF electrical. Since SSF shorted to ground causes SSF to be failed to high current (maximum pressure since SSE is directly proportional). F clutch is failed on. GO to Pinpoint Test A |
| P0999 | Shift Solenoid "F" Control Circuit High | MIL/KOEO, Continuous | This DTC indicates a short to power in the SSF electrical. Since SSF shorted to power causes SSF to be failed to low current (minimum pressure since SSF is directly proportional). E clutch is failed off. GO to Pinpoint Test A |
| P1001 | The KOER Not Able to Complete, KOER Aborted | None/KOER | RETRIEVE and RECORD all DTCs. REPAIR any self-test or CMDTCs first. CLEAR the DTC. RERUN the KOER self-test. If the DTC returns, REPROGRAM the PCM to the latest software. RERUN the KOER self-test. If the DTC returns, INSTALL a new PCM. Refer to PCM Guided Routine Testing . |
| P1397 | System Voltage Out Of Self Test Range | None/KOEO | INSPECT the PCM power and ground circuits for opens or short to ground. INSPECT the PCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. RUN the KOEO self-test. If DTC P1397 returns, REFER to: Charging System - 2.3L EcoBoost (231kW/314PS) . |
| P1636 | Inductive Signature Chip Communication Error | MIL/KOEO, Continuous | GO to Pinpoint Test G |
| P163E | Transmission Control Module Programming Error | MIL/KOEO, Continuous | GO to Pinpoint Test G |
| P163F | Transmission ID Block Corrupted, Not Programmed | MIL/KOEO, Continuous | GO to Pinpoint Test G |
| P1705 | Transmission Range Circuit Not Indicating Park/Neutral During Self Test | None/KOEO | CLEAR the DTC. RERUN the KOEO and KOER self-test. If DTC P1705 returns, GO to Pinpoint Test C |
| P1711 | Transmission Fluid Temperature Sensor Out Of Self Test Range | None/KOEO | CLEAR the DTC and RERUN the KOEO and KOER self-test. If the DTC returns, GO to Pinpoint Test B |
| P1744 | Torque Converter Clutch Solenoid Circuit Performance | Wrench/Continuous | DTC P1744 is a non-electrical DTC. CLEAR the DTC. If DTC P1744 returns, REFER to: Diagnosis By Symptom . |
| P1783 | Transmission Over Temperature Condition | Wrench/Continuous | CLEAR the DTC. If DTC P1783 returns, determine if this DTC was set in conjunction with any TFT sensor circuit DTCs and RESOLVE them first, otherwise REFER to: Transmission Cooling . |
| P1A02 | Transmission One Way Clutch Performance | Wrench/Continuous | This DTC sets when the PCM detects 3 failures of the one-way clutch to lock in 1st or 2nd gear allowing sun gear 1 to rotate backwards. CLEAR the DTC, road test the vehicle. If DTC P1A02 returns, it may indicate a one way clutch failure. REFER to: Transmission . |
| P2669 | Actuator Supply Voltage "B" Circuit/Open | MIL/Continuous | GO to Pinpoint Test A |
| P26C3 | Internal Control Module Transmission Range Sensor Performance | MIL, Wrench/KOEO, Continuous | CLEAR the DTC. If DTC P26C3 returns, TR sensor. REFER to: Transmission Range (TR) Sensor . |
| P2700 | Transmission Friction Element "A" Apply Time Range/Performance | Wrench/Continuous | This DTC sets with either P0751 (A clutch stuck off) and P0752 (A clutch stuck on), service the more specific DTC first. See DTCs P0751 and P0752 for potential causes. If P0751 and P0752 are not set refer to the associated symptoms, REFER to: A Clutch . |
| P2701 | Transmission Friction Element "B" Apply Time Range/Performance | Wrench/Continuous | This DTC sets with either P0756 (B clutch stuck off) and P0757 (B clutch stuck on), service the more specific DTC first. See DTCs P0756 and P0757 for potential causes. If these DTCs are not set refer to the associated symptoms, REFER to: B Clutch . |
| P2702 | Transmission Friction Element "C" Apply Time Range/Performance | Wrench/Continuous | This DTC set with either P0761 (C clutch stuck off) and P0762 (C clutch stuck on) - service the more specific DTC first (if present). See P0761 and P0762 for potential causes first. If these DTCs are not set refer to the associated symptoms, REFER to: C Clutch . |
| P2703 | Transmission Friction Element "D" Apply Time Range/Performance | Wrench/Continuous | This DTC set with either P0766 (D clutch stuck off) and P0767 (D clutch stuck on) service the more specific DTC first (if present). See P0766 and P0767 for potential causes first. If these DTCs are not set, refer to the associated symptoms, REFER to: D Clutch . |
| P2704 | Transmission Friction Element "E" Apply Time Range/Performance | Wrench/Continuous | This DTC sets with either P0771 (E clutch stuck off) and P0772 (E clutch stuck on) service the more specific DTC first (if present). See P0771 and P0772 for potential causes. If these DTCs are not set, refer to the associated symptoms, REFER to: E Clutch . |
| P2705 | Transmission Friction Element "F" Apply Time Range/Performance | Wrench/Continuous | This DTC sets with either P2707 (clutch F stuck off) and P2708 (clutch F stuck on). Service the more specific DTC first. See DTCs P2707 and P2708 for potential causes. If these DTCs are not set, refer to the associated symptoms. REFER to: F Clutch . |
| P2707 | Shift Solenoid "F" Performance/Stuck Off | MIL/Continuous | The F clutch is stuck off due to a non-electrical fault. Multiple attempts to apply the F clutch failed. See condition F clutch does not apply. REFER to: F Clutch . |
| P2708 | Shift Solenoid "F" Stuck On | MIL/Continuous | The F clutch is stuck on due to a non-electrical fault. Multiple attempts to release the F clutch failed. See condition F clutch always applied. REFER to: F Clutch . |
| P2709 | Shift Solenoid "F" Electrical | MIL/KOEO, Continuous | SSF (controls F clutch) VFS circuit failure non-MIL "sister" DTCs of P097F, P0998, P0999 used to illuminate the Wrench Light. If one of the more specific circuit codes is set, follow repair procedures for that code. GO to Pinpoint Test A |
| P2710 | Shift Solenoid "F" Intermittent | MIL/Continuous | The PCM detected SSF fault, but the fault did not last long enough for the PCM to set a more specific SSF DTC. Inspect SSF wiring and connectors for damage. |
| P2745 | Intermediate Shaft Speed Sensor "B" Circuit | MIL/KOEO, Continuous | An open circuit fault was detected by the PCM smart driver. GO to Pinpoint Test D |
| P2746 | Intermediate Shaft Speed Sensor "B" Circuit Range/Performance | MIL/Continuous | GO to Pinpoint Test F |
| P2747 | Intermediate Shaft Speed Sensor "B" Circuit No Signal | Wrench/Continuous | GO to Pinpoint Test D |
| P2748 | Intermediate Shaft Speed Sensor "B" Circuit Intermittent | MIL/Continuous | GO to Pinpoint Test D |
| P2758 | Torque Converter Clutch Pressure Control Solenoid Stuck On | MIL/Continuous | TCC stuck on when commanded off due to non-electrical failure. CLEAR the DTC. If DTC P2758 returns, REFER to: Diagnosis By Symptom . |
| P2760 | Torque Converter Clutch Pressure Control Solenoid Intermittent | MIL/Continuous | The PCM detected TCC fault, but the fault did not last long enough for the PCM to set a more specific TCC DTC. Inspect TCC solenoid wiring and connectors for damage. |
| P2769 | Torque Converter Clutch Circuit Low | MIL/Continuous | This DTC indicates a short to ground in the TCC electrical. Since TCC shorted to ground causes TCC to be failed to high current (maximum pressure since TCC is directly proportional). TCC is failed on. GO to Pinpoint Test E |
| P2770 | Torque Converter Clutch Circuit High | MIL/Continuous | This DTC indicates a short to power in the TCC electrical. Since TCC shorted to power causes TCC to be failed to low current (minimum pressure since TCC is directly proportional). TCC is failed off. CLEAR the DTC. If DTC P2783 returns, INSPECT TCC control valve for sticking. REFER to: Main Control Valve Body . |
| P2783 | Torque Converter Temperature Too High | None/Continuous | The TCC control valve is stuck in a position that provides no flow when the TCC is commanded off. The TCC pumps down when commanded off, causing loss of torque multiplication through the TCC. |
| P27B2 | Internal Control Module Transmission Range Control Performance | Wrench/Continuous | GO to Pinpoint Test H |
| P27B3 | Internal Control Module Transmission Gear Select Performance | Wrench/Continuous | GO to Pinpoint Test H |
| P27B4 | Internal Control Module Transmission Gear Direction Control Performance | Wrench/Continuous | GO to Pinpoint Test H |
| P27B5 | Internal Control Module Transmission Gear Ratio Control Performance | Wrench/Continuous | GO to Pinpoint Test H |
| P27B6 | Internal Control Module Transmission Speed Sensor Performance | Wrench/Continuous | GO to Pinpoint Test H |
| P2801 | Transmission Range Sensor "B" Circuit Range/Performance | MIL/KOEO, Continuous | GO to Pinpoint Test C |
| P2802 | Transmission Range Sensor "B" Circuit Low | MIL/KOEO, Continuous | GO to Pinpoint Test C |
| P2803 | Transmission Range Sensor "B" Circuit High | MIL/KOEO, Continuous | GO to Pinpoint Test C |
| P2804 | Transmission Range Sensor "B" Circuit Intermittent | Wrench/KOEO, Continuous | GO to Pinpoint Test C |
| P2805 | Transmission Range Sensor "A"/"B" Correlation | MIL/KOEO, Continuous | GO to Pinpoint Test C |