Parking Aid System DTCS

Diagnostics in this service information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .

DTC INDEX

DTC	Description	Action
B1B44:12	Right Rear Outer Sensor: Circuit Short To Battery	GO to Pinpoint Test D
B1B44:14	Right Rear Outer Sensor: Circuit Short To Ground or Open	GO to Pinpoint Test C
B1B44:96	Right Rear Outer Sensor: Component Internal Failure	GO to Pinpoint Test E
B1B46:12	Right Rear Inner Sensor: Circuit Short To Battery	GO to Pinpoint Test D
B1B46:14	Right Rear Inner Sensor: Circuit Short To Ground or Open	GO to Pinpoint Test C
B1B46:96	Right Rear Inner Sensor: Component Internal Failure	GO to Pinpoint Test E
B1B48:12	Left Rear Outer Sensor: Circuit Short To Battery	GO to Pinpoint Test D
B1B48:14	Left Rear Outer Sensor: Circuit Short To Ground or Open	GO to Pinpoint Test C
B1B48:96	Left Rear Outer Sensor: Component Internal Failure	GO to Pinpoint Test E
B1B50:12	Left Rear Inner Sensor: Circuit Short To Battery	GO to Pinpoint Test D
B1B50:14	Left Rear Inner Sensor: Circuit Short To Ground or Open	GO to Pinpoint Test C
B1B50:96	Left Rear Inner Sensor: Component Internal Failure	GO to Pinpoint Test E
B1B58:11	Rear Sensors Power Circuit: Circuit Short To Ground	GO to Pinpoint Test B
U0100:00	Lost Communication With ECM/ PCM "A": No Sub Type Information	GO to Pinpoint Test F
U0101:00	Lost Communication with TCM: No Sub Type Information	GO to Pinpoint Test G
U0121:00	Lost Communication With ABS Control Module: No Sub Type Information	GO to Pinpoint Test H
U0146:00	Lost Communication With GWM: No Sub Type Information	GO to Pinpoint Test J
U0155:00	Lost Communication With IPC Control Module: No Sub Type Information	GO to Pinpoint Test K
U0212:00	Lost Communication With SCCM: No Sub Type Information	GO to Pinpoint Test L
U0253:00	Lost Communication With APIM: No Sub Type Information	GO to Pinpoint Test M
U0256:00	Lost Communication With FCIM "A": No Sub Type Information	GO to Pinpoint Test N
U0257:00	Lost Communication With FCDIM: No Sub-Type Information	GO to Pinpoint Test O
U0401:00	Invalid Data Received From ECM/ PCM A: No Sub Type Information	This DTC sets when the PAM receives invalid network data from the PCM with a faulted signal data input. RETRIEVE and REPAIR all non-network DTCs in other modules on the network.
U0402:00	Invalid Data Received From TCM: No Sub Type Information	This DTC sets when the PAM receives invalid network data from the TCM with a faulted signal data input. RETRIEVE and REPAIR all non-network DTCs in other modules on the network.
U0415:00	Invalid Data Received From ABS Control Module: No Sub Type Information	This DTC sets when the PAM receives invalid network data from the ABS module with a faulted signal data input. RETRIEVE and REPAIR all non-network DTCs in other modules on the network.
U0422:00	Invalid Data Received From BCM: No Sub Type Information	This DTC sets when the PAM receives invalid network data from the BCM with a faulted signal data input. RETRIEVE and REPAIR all non-network DTCs in other modules on the network.
U0423:00	Invalid Data Received from IPC Control Module: No Sub Type Information	This DTC sets when the PAM receives invalid network data from the IPC with a faulted signal data input. RETRIEVE and REPAIR all non-network DTCs in other modules on the network.
U0429:00	Invalid Data Received From SCCM: No Sub Type Information	This DTC sets when the PAM receives invalid network data from the SCCM with a faulted signal data input. RETRIEVE and REPAIR all non-network DTC in other modules on the network.
U0554:00	Invalid Data Received From APIM: No Sub Type Information	This DTC sets when the PAM receives invalid network data from the APIM with a faulted signal data input. RETRIEVE and REPAIR all non-network DTCs in other modules on the network.
U0557:00	Invalid Data Received From FCIM "A": No Sub Type Information	This DTC sets when the PAM receives invalid network data from the FCIM with a faulted signal data input. RETRIEVE and REPAIR all non-network DTCs in other modules on the network.
U0558:00	Invalid Data Received From FCDIM: No Sub Type Information	This DTC sets when the PAM receives invalid network data from the FCDIM with a faulted signal data input. RETRIEVE and REPAIR all non-network DTCs in other modules on the network.
U2024:41	Control Module Cal-Config Data: General Checksum Failure	CLEAR the DTCs and REPEAT the PAM self-test. If DTC U2024:41 is retrieved again, PROGRAM the Parking Aid Module (PAM) REFER to: Module Configuration - System Operation and Component Description . REPEAT the self-test. If DTC U2024:41 is retrieved again, Refer to BCM Hardware Testing .
U2100:00	Initial Configuration Not Complete: No Sub Type Information	CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure. Refer to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, Refer to BCM Hardware Testing .
U2101:00	Control Module Configuration Incompatible: No Sub Type Information	CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure. Refer to: Module Configuration - System Operation and Component Description .
U3000:45	Control Module: Program Memory Failure	This DTC sets when the PAM receives a Program Memory Failure signal from the ECU. RETRIEVE and REPAIR all non-network DTCs in other modules on the network.
U3000:46	Control Module: Calibration / Parameter Memory Failure	This DTC sets when the PAM receives a Calibration / Parameter Memory Failure signal from the ECU. RETRIEVE and REPAIR all non-network DTCs in other modules on the network.