2.0L ECOBOOST (177KW/240PS) - Mi4
DTC INDEX
| DTC | Description | Component | Action |
|---|---|---|---|
| P0218 | Transmission Fluid Temperature Sensor "A" Over Temperature Condition Engine | Transmission over temperature |
NOTE:
P0218 causes the powertrain to limit torque to prevent transmission overheating. The DTC P0218 may set in conjunction with DTC P1783. CLEAR the DTC. If DTC P0218 returns, determine if this DTC was set in conjunction with any transmission fluid temperature sensor circuit DTCs and RESOLVE them first, otherwise REFER to: Transmission Cooling
. |
| P0657 | Actuator Supply Voltage "A" Circuit/Open | Transmission solenoid power control | Power to all solenoids has been interrupted. CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST F : DTC P0657 . |
| P0701 | Transmission Control System Range/Performance | Transmission hydraulic and clutch systems (including non-electrical shift solenoid faults, main control valve body and clutch(s)). | Intermittent clutch on fault and may set with DTCs P2700, P2701, P2702, P2703 and/or P2704. CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . |
| P0702 | Transmission Control System Electrical | Low or high system voltage | INSPECT the PCM power and ground circuits for opens or short to ground. INSPECT the PCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. RERUN the KOEO and (KOER self-test. If the DTC returns, REFER to: Battery . |
| P0706 | Transmission Range Sensor "A" Circuit Range/Performance | TR sensor | The TR sensor outputs a duty cycle indicating manual lever position. This DTC sets when the duty cycle is greater or less than the expected duty cycle by 50Hz or more. Engine may not crank. CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST J : DTCS P0706, P0707, P0708, P1702, P1705, P1921 . |
| P0707 | Transmission Range Sensor "A" Circuit Low | TR sensor | Engine may not crank, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST J : DTCS P0706, P0707, P0708, P1702, P1705, P1921 |
| P0708 | Transmission Range Sensor "A" Circuit High | TR sensor | Engine may not crank, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST J : DTCS P0706, P0707, P0708, P1702, P1705, P1921 |
| P0710 | Transmission Fluid Temperature Sensor "A" Circuit | TFT | DTC P0710 may set. CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST G : DTCS P0710, P0711, P0712, P0713, P1711, P1783 REPAIR the more specific DTC first. |
| P0711 | Transmission Fluid Temperature Sensor "A" Circuit Range/Performance | TFT | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST G : DTCS P0710, P0711, P0712, P0713, P1711, P1783 |
| P0712 | Transmission Fluid Temperature Sensor "A" Circuit Low | TFT | DTC P0710 may set. CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST G : DTCS P0710, P0711, P0712, P0713, P1711, P1783 REPAIR the more specific DTC first. |
| P0713 | Transmission Fluid Temperature Sensor "A" Circuit High | TFT | DTC P0710 may set. CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST G : DTCS P0710, P0711, P0712, P0713, P1711, P1783 REPAIR the more specific DTC first. |
| P0715 | Turbine/Input Shaft Speed Sensor "A" Circuit | TSS sensor | DTC P0717 may set. CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST K : DTCS P0715, P0717, P0718 REPAIR the more specific DTC first. |
| P0717 | Turbine/Input Shaft Speed Sensor "A" Circuit No Signal | TSS sensor | DTC P0717 may set. CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST K : DTCS P0715, P0717, P0718 REPAIR the more specific DTC first. |
| P0718 | Turbine/Input Shaft Speed Sensor "A" Circuit Intermittent | TSS sensor | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST K : DTCS P0715, P0717, P0718 |
| P0720 | Output Shaft Speed Sensor Circuit | OSS Sensor |
NOTE:
DTC P0720 sets when vehicle conditions (mainly turbine speed) indicate that OSS output should be present, but the OSS signal is 0 RPM. Excessive transmission slippage in D or R may set P0720. REPAIR any transmission slip symptoms first. DTC P0722 may set. CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST L : DTCS P0720, P0721, P0722
REPAIR the more specific DTC first. |
| P0721 | Output Shaft Speed Sensor Circuit Range/Performance | OSS sensor | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST L : DTCS P0720, P0721, P0722 |
| P0722 | Output Shaft Speed Sensor Circuit No Signal | OSS sensor | DTC P0720 may set. CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST L : DTCS P0720, P0721, P0722 REPAIR the more specific DTC first. |
| P0729 | Gear 6 Incorrect Ratio | O/D or intermediate clutch system faults (includes non-electrical SSB, SSC faults, main control valve body and clutch) | CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Shift Concerns, No 5-6 Shift/Harsh/Soft/Slipping. |
| P0731 | Gear 1 Incorrect Ratio | Low/reverse clutch system faults (includes non-electrical SSD, SSA, SSE faults, forward clutch system faults. | CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Shift Concerns, No 1-2 Shift/Harsh/Soft/Slipping. |
| P0732 | Gear 2 Incorrect Ratio | Low/reverse clutch system faults (includes non-electrical SSC faults, main control valve body and clutch) | CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Shift Concerns, No 1-2 Shift/Harsh/Soft/Slipping. |
| P0733 | Gear 3 Incorrect Ratio | Direct clutch system faults (includes non-electrical SSB faults, main control valve body and clutch) | CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Shift Concerns, No 2-3 Shift/Harsh/Soft/Slipping. |
| P0734 | Gear 4 Incorrect Ratio | O/D clutch system faults (includes non-electrical SSD faults, main control valve body and clutch) | CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Shift Concerns, No 3-4 Shift/Harsh/Soft/Slipping. |
| P0735 | Gear 5 Incorrect Ratio | Direct clutch system faults (includes non-electrical SSB faults, main control valve body and clutch) | CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Shift Concerns, No 4-5 Shift/Harsh/Soft/Slipping. |
| P073D | Unable to Engage Neutral | Direct or forward clutch packs | This DTC may set when there is a mechanical/hydraulic concern with the direct or forward clutch pack, possibly deformed clutch plates or a rolled clutch seal allowing the direct clutch or the forward clutch to mechanically or hydraulically apply in neutral. PLACE the transmission in neutral with the engine running to see if there is any creep torque, this fault causes the transmission to partially engage forward gear in neutral. This DTC may set with P0752, P0757, P0762, and/or P0767. CLEAR the DTC. If the DTC returns, check the transmission for internal failure. Refer to: Transmission . |
| P0740 | Torque Converter Clutch Solenoid Circuit/Open | TCC solenoid electrical faults | DTC P0743 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST H : DTCS P0740, P0742, P0743. P0744, P2760 |
| P0741 | Torque Converter Clutch Solenoid Circuit Performance/Stuck Off | TCC system faults (includes TCC, main control main control valve body and non-electrical solenoid faults) | P0741 is a non-electrical DTC, that sets when engine RPM was at least 80 RPM greater than TSS when lock up was commanded 3 consecutive times. Refer to: Torque Converter Clutch (TCC) . |
| P0742 | Torque Converter Clutch Solenoid Circuit Stuck On | TCC solenoid electrical faults | DTC P0743 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST H : DTCS P0740, P0742, P0743. P0744, P2760 |
| P0743 | Torque Converter Clutch Solenoid Circuit Electrical | TCC solenoid electrical faults | DTC P0740, P0742 and/or P0744 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST H : DTCS P0740, P0742, P0743. P0744, P2760 |
| P0744 | Torque Converter Clutch Solenoid Circuit Intermittent | TCC solenoid electrical faults | DTC P0743 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST H : DTCS P0740, P0742, P0743. P0744, P2760 REPAIR the more specific DTC first. |
| P0748 | Pressure Control Solenoid "A" Electrical | LPC solenoid electrical faults | DTC P0960, P0962 and/or P0963 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST I : DTCS P0748, P0960, P0961, P0962, P0963 REPAIR the more specific DTC first. |
| P0750 | Shift Solenoid "A" | SSA electrical faults | DTC P0751 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST A : DTCS P0750, P0753, P0754, P0973, P0974 REPAIR the more specific DTC first. |
| P0751 | Shift Solenoid "A" Performance/Stuck Off | Forward clutch system faults (includes non-electrical SSA faults, main control valve body and clutch) | DTC P2700 may set, CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Engagement Concerns, No Forward. |
| P0752 | Shift Solenoid "A" Stuck On | Forward clutch system faults (includes non-electrical SSA faults, main control valve body and clutch) | CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Shift Concerns, Only Gears 1, 2, 3, 4 Available. |
| P0753 | Shift Solenoid "A"Electrical | SSA electrical faults | DTC P0750, P0973 and/or P0974 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST A : DTCS P0750, P0753, P0754, P0973, P0974 REPAIR the more specific DTC first. |
| P0754 | Shift Solenoid "A" Intermittent | SSA electrical faults | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST A : DTCS P0750, P0753, P0754, P0973, P0974 |
| P0755 | Shift Solenoid "B" | SSA electrical faults | DTC P0756 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST B : DTCS P0755, P0758, P0759, P0976, P0977 REPAIR the more specific DTC first. |
| P0756 | Shift Solenoid "B" Performance/Stuck Off | Direct clutch system fault (includes non-electrical SSB faults, main control valve body and clutch) | DTC P2701 may set, CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Shift Concerns, Only Gears 3 And 5. |
| P0757 | Shift Solenoid "B" Stuck On | Direct clutch system fault (includes non-electrical SSB faults, main control valve body and clutch) SSB electrical faults SSB electrical faults | DTC P2701 may set, CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Shift Concerns, No 2-3 Shift/Harsh/Soft/Slipping. |
| P0758 | Shift Solenoid "B" Electrical | SSB electrical faults | DTC P0755, P0976 and/or P0977 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST B : DTCS P0755, P0758, P0759, P0976, P0977 REPAIR the more specific DTC first. |
| P0759 | Shift Solenoid "B" Intermittent | SSB electrical faults | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST B : DTCS P0755, P0758, P0759, P0976, P0977 |
| P0760 | Shift Solenoid "C" | SSC electrical faults | DTC P0761 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST C : DTCS P0760, P0763, P0764, P0979, P0980 REPAIR the more specific DTC first. |
| P0761 | Shift Solenoid "C" Performance/Stuck Off | Intermediate clutch system faults (includes clutch, main control valve body and non-electrical SSC faults) | DTC P2702 may set, CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Shift Concerns, No 1-2 Shift/Harsh/Soft/Slipping. |
| P0762 | Shift Solenoid "C" Stuck On | Intermediate clutch system faults (includes clutch, main control valve body and non-electrical SSC faults) | DTC P0763 may set, CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Shift Concerns, Only Gears 2 and 6 Available. |
| P0763 | Shift Solenoid "C" Electrical | SSC electrical faults | DTC P0760, P0979 and/or P0980 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST C : DTCS P0760, P0763, P0764, P0979, P0980 REPAIR the more specific DTC first. |
| P0764 | Shift Solenoid "C" Intermittent | SSC electrical faults | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST C : DTCS P0760, P0763, P0764, P0979, P0980 |
| P0765 | Shift Solenoid "D" | SSD electrical faults | DTC P0766 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST D : DTCS P0765, P0768, P0769, P0982, P0983 REPAIR the more specific DTC first. |
| P0766 | Shift Solenoid "D" Performance/Stuck Off | SSD electrical faults | DTC P2704 may set, CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Shift Concerns, No 1-2 Shift/Harsh/Soft/Slipping Or Only Gears 1 and R Available. |
| P0767 | Shift Solenoid "D" Stuck On | O/D Clutch System Faults (includes non-electrical SSD faults, main control valve body and clutch) | DTC P07A9 and/or P2704 may set, CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Engagement Concerns, No Reverse and for Shift Concerns/No 3-4 Shift/Harsh/Soft/Slipping. |
| P0768 | Shift Solenoid "D" Electrical | SSD electrical faults | DTC P0765, P0982 and/or P0983 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST D : DTCS P0765, P0768, P0769, P0982, P0983 REPAIR the more specific DTC first. |
| P0769 | Shift Solenoid "D" Intermittent | SSD electrical faults | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST D : DTCS P0765, P0768, P0769, P0982, P0983 |
| P0770 | Shift Solenoid "E" | SSE electrical faults | DTC P0773 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST E : DTCS P0770, P0773, P0774 REPAIR the more specific DTC first. |
| P0771 | Shift Solenoid "E" Performance/Stuck Off | SSE non-electrical faults (SSE and main control valve body) | DTC P0984 may set, CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Engagement Concerns, No Reverse |
| P0772 | Shift Solenoid "E" Stuck On | SSE non-electrical faults (SSE and main control valve body) | DTC P0984 may set, CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Shift Concerns, No 3-4 Shift/Harsh/Soft/Slipping. |
| P0773 | Shift Solenoid "E" Electrical | SSE electrical faults | DTC P0770 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST E : DTCS P0770, P0773, P0774 REPAIR the more specific DTC first. |
| P0774 | Shift Solenoid "E" Intermittent | SSE electrical faults | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST E : DTCS P0770, P0773, P0774 |
| P07A5 | Transmission Friction Element "B" Stuck On | Direct clutch | CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Shift Concerns, No 2-3 Shift/Harsh/Soft/Slipping. |
| P07A8 | Transmission Friction Element "D" Stuck Off | Low/reverse clutch | CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Shift Concerns, No 1-2 Shift/Harsh/Soft/Slipping or Only Gears 1 and R Available. |
| P07A9 | Transmission Friction Element "D" Stuck On | Low/reverse clutch | DTC P0767 may set, CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Engagement Concerns, No Reverse and for Shift Concerns, No 3-4 Shift/Harsh/Soft/Slipping. |
| P07AA | Transmission Friction Element "E" Stuck Off | Overdrive clutch | CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Engagement Concerns. |
| P0815 | Upshift Switch Circuit | Upshift switch electrical | REFER to: External Controls . |
| P0816 | Downshift Switch Circuit | Downshift switch electrical | REFER to: External Controls . |
| P0867 | Transmission Fluid Pressure | Transmission hydraulic and clutch systems | CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . |
| P0882 | TCM Power Input Signal Low | TCM power input signal low | INSPECT the PCM power and ground circuits for opens or short to ground. INSPECT the PCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. If the DTC returns, REFER to: Charging System - 2.5L Duratec (125kW/170PS) . |
| P0883 | TCM Power Input Signal High | TCM power input signal high | CLEAR the DTC. If the DTC returns, REFER to: Charging System - 2.5L Duratec (125kW/170PS) . |
| P0960 | Pressure Control Solenoid "A" Control Circuit/Open | LPC solenoid electrical faults | DTC P0748 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST I : DTCS P0748, P0960, P0961, P0962, P0963 REPAIR the more specific DTC first. |
| P0961 | Pressure Control Solenoid "A" Control Circuit Range/Performance | LPC solenoid electrical faults | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST I : DTCS P0748, P0960, P0961, P0962, P0963 |
| P0962 | Pressure Control Solenoid "A" Control Circuit Low | LPC solenoid electrical faults | DTC P0748 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST I : DTCS P0748, P0960, P0961, P0962, P0963 REPAIR the more specific DTC first. |
| P0963 | Pressure Control Solenoid "A" Control Circuit High | LPC solenoid electrical faults | DTC P0748 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST I : DTCS P0748, P0960, P0961, P0962, P0963 REPAIR the more specific DTC first. |
| P0973 | Shift Solenoid "A" Control Circuit Low | SSA electrical faults | DTC P0753 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST A : DTCS P0750, P0753, P0754, P0973, P0974 REPAIR the more specific DTC first. |
| P0974 | Shift Solenoid "A" Control Circuit High | SSA electrical faults | DTC P0748 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST A : DTCS P0750, P0753, P0754, P0973, P0974 REPAIR the more specific DTC first. |
| P0976 | Shift Solenoid "B" Control Circuit Low | SSB electrical faults | DTC P0758 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST B : DTCS P0755, P0758, P0759, P0976, P0977 REPAIR the more specific DTC first. |
| P0977 | Shift Solenoid "B" Control Circuit High | SSB electrical faults | DTC P0758 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST B : DTCS P0755, P0758, P0759, P0976, P0977 REPAIR the more specific DTC first. |
| P0979 | Shift Solenoid "C" Control Circuit Low | SSC electrical faults | DTC P0763 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST C : DTCS P0760, P0763, P0764, P0979, P0980 REPAIR the more specific DTC first. |
| P0980 | Shift Solenoid "C" Control Circuit High | SSC electrical faults | DTC P0763 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST C : DTCS P0760, P0763, P0764, P0979, P0980 REPAIR the more specific DTC first. |
| P0982 | Shift Solenoid "D" Control Circuit Low | SSD electrical faults | DTC P0768 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST D : DTCS P0765, P0768, P0769, P0982, P0983 REPAIR the more specific DTC first. |
| P0983 | Shift Solenoid "D" Control Circuit High | SSD electrical faults | DTC P0768 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST D : DTCS P0765, P0768, P0769, P0982, P0983 REPAIR the more specific DTC first. |
| P0984 | Shift Solenoid "E" Range/Performance | SSE electrical faults | DTC P0771 and/or P0772 may set, CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Engagement Concerns. |
| P0B0D | Electric/Auxiliary Transmission Fluid Pump Motor Control Module | Electric transmission fluid pump motor | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST N : DTCS P0B0D:00, P0C27:00, P0C28:00, P0C29:00, P0C2A:00 |
| P0C27 | Electric Transmission Fluid Pump Motor Current Low | Electric transmission fluid pump motor | Verify Fluid level. Refer to: Transmission Fluid Level Check . If fluid level is ok, Clear any DTCs, then carry out prime procedure: Prime the Transmission Fluid Auxiliary Pump. Using a diagnostic scan tool, Key ON, Engine OFF, command TRANS_PMP_CMD to 80% for 30 seconds. Carry out a road test until there is a stop/start event. If the restart is harsh, repeat the Transmission Fluid Pump prime procedure. Continue road test and evaluate each stop / start event. Repeat prime procedure until three consecutive normal stop/start events are achieved. Clear DTCs. |
| P0C28 | Electric Transmission Fluid Pump Motor Current Low | Electric transmission fluid pump motor | This DTC applies to auto-start-stop vehicles only. This DTC sets when the PCM detects low current (20% to 25% duty cycle). Auto-Start-Stop unavailable and the engine only stops when the operator turns the ignition off. The engine may restart unexpectedly when the vehicle is stopped. CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST N : DTCS P0B0D:00, P0C27:00, P0C28:00, P0C29:00, P0C2A:00 |
| P0C29 | Electric Transmission Fluid Pump Motor Current High | Electric transmission fluid pump motor | This DTC applies to auto-start-stop vehicles only. This DTC sets when the PCM detects high current (20% to 25% duty cycle). Auto-Start-Stop unavailable and the engine only stops when the operator turns the ignition off. The engine may restart unexpectedly when the vehicle is stopped. CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST N : DTCS P0B0D:00, P0C27:00, P0C28:00, P0C29:00, P0C2A:00 |
| P0C2A | Electric Transmission Fluid Pump Motor Stalled | Electric transmission fluid pump motor | This DTC applies to auto-start-stop vehicles only. This DTC sets when the PCM commands the electric transmission fluid pump on and does not detect the corresponding increase in pressure indicating a stalled pump motor. Auto-Start-Stop unavailable and the engine only stops when the operator turns the ignition off. The engine may restart unexpectedly when the vehicle is stopped. CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST M : DTCS P0C2A:00, P0C2C:00, P0C2D:00, P0C2E:00, P2796:00 . |
| P0C2C | Electric Transmission Fluid Pump Control Module Feedback Signal Range/Performance | Electric transmission fluid pump motor module | This DTC applies to auto-start-stop vehicles only. This DTC sets when the PCM detects a duty cycle that does not match a defined duty cycle range. Auto-Start-Stop unavailable and the engine onlys stop when the operator turns the ignition off. The engine may restart unexpectedly when the vehicle is stopped. CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST M : DTCS P0C2A:00, P0C2C:00, P0C2D:00, P0C2E:00, P2796:00 |
| P0C2D | Electric Transmission Fluid Pump Control Module Feedback Signal Low | Electric transmission fluid pump motor module | This DTC applies to auto-start-stop vehicles only. This DTC sets when the PCM detects a duty cycle that is out of range low (less than 10%). Auto-Start-Stop unavailable and the engine only stops when the operator turns the ignition off. The engine may restart unexpectedly when the vehicle is stopped. CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST M : DTCS P0C2A:00, P0C2C:00, P0C2D:00, P0C2E:00, P2796:00 |
| P0C2E | Electric Transmission Fluid Pump Control Module Feedback Signal High | Electric transmission fluid pump motor module | This DTC applies to auto-start-stop vehicles only. This DTC sets when the PCM detects a duty cycle that is out of range high (greater than 90%). Auto-Start-Stop unavailable and the engine only stops when the operator turns the ignition off. The engine may restart unexpectedly when the vehicle is stopped. CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST M : DTCS P0C2A:00, P0C2C:00, P0C2D:00, P0C2E:00, P2796:00 |
| P1001 | KOEO Not Able to Complete, KOER Aborted | PCM | RETERIVE and RECORD all Transmission solenoid power control. REPAIR any self-test or CMDTCs first. CLEAR the DTC. RERUN the KOER self-test. If the DTC returns, REPROGRAM the PCM to the latest calibration. RERUN the KOER self-test. If the DTC returns, INSTALL a new PCM. Refer to: Powertrain Control Module (PCM) . After installing the new PCM, PERFORM the Transmission Strategy Download, REFER to: Transmission Strategy Download . |
| P1397 | System Voltage Out Of Self Test Range | System voltage out of self test range | INSPECT the PCM power and ground circuits for opens or short to ground. INSPECT the PCM connector for damaged or pushed-out terminals, corrosion or loose wires. CLEAR the DTC. RUN the KOEO self-test. If the DTC returns, REFER to: Charging System - 2.5L Duratec (125kW/170PS) . |
| P1501 | Vehicle Speed Sensor Out Of Self Test Range | Vehicle speed sensor or circuit | Vehicle speed not at 0 during the KOEO and/or KOER self-test. CLEAR the DTC and RERUN the KOEO and KOER self-test. If the DTC returns, CHECK for OSS sensor DTC and ABS wheel speed sensor DTC and REPAIR the more specific DTC first. Refer to: Anti-Lock Brake System (ABS) and Stability Control . |
| P1636 | Inductive Signature Chip Communication Error | PCM | CLEAR the DTC. If the DTC returns, INSTALL a new PCM. Refer to: Powertrain Control Module (PCM) . After installing the new PCM, PERFORM the Transmission Strategy Download, REFER to: Transmission Strategy Download . |
| P163E | Transmission Control Module Programming Error | Transmission control module programming error | CLEAR the DTC. REPROGRAM the PCM with the latest calibration. If the DTC returns, INSTALL a new PCM. Refer to: Powertrain Control Module (PCM) . After installing the new PCM, PERFORM the Transmission Strategy Download, REFER to: Transmission Strategy Download . |
| P163F | Transmission ID Block Corrupted, Not Programmed | Transmission ID memory block corrupted, not programmed | CLEAR the DTC. REPROGRAM the PCM with the latest calibration. If the DTC returns, INSTALL a new PCM. Refer to: Powertrain Control Module (PCM) . After installing the new PCM, PERFORM the Transmission Strategy Download, REFER to: Transmission Strategy Download . |
| P1702 | Transmission Range Sensor Circuit Intermittent | TR | DTC P0706, P0707 and/or P0708 may set, CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST J : DTCS P0706, P0707, P0708, P1702, P1705, P1921 REPAIR the more specific DTC first. |
| P1705 | Transmission Range Circuit Not Indicating Park/Neutral During Self Test | TR sensor | The selector lever was not in park or neutral during the self-test. CLEAR the DTC and RERUN the KOEO and KOER self-test. |
| P1711 | Transmission Fluid Temperature Sensor Out Of Self Test Range | TFT sensor | CLEAR the DTC and RERUN the KOEO and KOER self-test. If the DTC returns, GO to PINPOINT TEST G : DTCS P0710, P0711, P0712, P0713, P1711, P1783 |
| P1744 | Torque Converter Clutch Solenoid Circuit Performance | TCC system faults (includes TCC, main control valve body and non-electrical solenoid faults) | DTC P1744 is a non-electrical DTC. CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Torque Converter Operation Concerns, No Apply. |
| P175A | Transmission Fluid Over Temperature Condition - Electric Transmission Fluid Pump Disabled | Electric transmission fluid pump | The temperature sensor in the Transmission Fluid Auxiliary Pump detected an overheat condition. CLEAR DTC and road test the vehicle. If DTC returns, INSTALL a new Transmission Fluid Auxiliary Pump. Refer to: Transmission Fluid Auxiliary Pump . |
| P177F | Unable to Engage Neutral | Direct or forward clutch pack | This DTC may set when there is a mechanical/hydraulic concern with the direct or forward clutch pack, possibly deformed clutch plates or a rolled clutch seal allowing the direct clutch or the forward clutch to mechanically or hydraulically apply in neutral. PLACE the transmission in neutral with the engine running to see if there is any creep torque, this fault causes the transmission to partially engage forward gear in neutral. This DTC may set with P0752, P0757, P0762, and/or P0767. CLEAR the DTC. If the DTC returns, check the transmission for internal failure. Refer to: Transmission . |
| P1780 | Transmission Control Switch (O/D Cancel) Circuit Out Of Self Test Range | Transmission control switch | REFER to: External Controls . |
| P1783 | Transmission Overtemperature Condition | Transmission over temperature | MONITOR the TFT sensor PID and TCC PID. ROAD TEST the vehicle and MONITOR the TFT sensor and TCC solenoid electrical operation. If DTC P0741 is set, REPAIR DTC P0741 first. CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST G : DTCS P0710, P0711, P0712, P0713, P1711, P1783 |
| P1921 | Transmission Range Signal | TR switch | Engine may not crank. DTC P0706, P0707 and/or P0708 may set. CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST J : DTCS P0706, P0707, P0708, P1702, P1705, P1921 REPAIR the more specific DTC first. |
| P2700 | Transmission Friction Element "A" Apply Time Range/Performance | Forward clutch system faults (includes non-electrical SSA faults, main control valve body and clutch) | DTC P2700 is a non-electrical DTC. DTC P0751 and/or P0752 may set. CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Engagement Concerns, No Forward Or Delayed, Soft Forward and/or Shift Concerns, Only Gears 1, 2, 3, 4 Available. |
| P2701 | Transmission Friction Element "B" Apply Time Range/Performance | Direct clutch system faults (includes non-electrical SSB faults, main control valve body and clutch) | DTC P2701 is a non-electrical DTC. DTC P0756 and/or P0757 may set. CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Shift Concerns, Only Gears 3 and 5 Available. |
| P2702 | Transmission Friction Element "C" Apply Time Range/Performance | Intermediate clutch system faults (includes clutch, main control valve body and non-electrical SSC faults) | DTC P2702 is a non-electrical DTC. DTC P0761 and/or P0762 may set. CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Shift Concerns, No 1-2 Shift/Harsh/Soft/Slipping or No 5-6 Shift/Harsh/Soft/Slipping or Only Gears 2 and 6 Available. |
| P2703 | Transmission Friction Element "D" Apply Time Range/Performance | Low/reverse clutch and OWC faults | DTC P2703 is a non-electrical DTC. DTC P0766 and/or P0768 may set. CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Engagement Concerns, No Reverse. |
| P2704 | Transmission Friction Element "E" Apply Time Range/Performance | O/D clutch system faults (includes non-electrical SSD faults, main control valve body and clutch) | DTC P2704 is a non-electrical DTC. DTC P0771 and/or P0772 may set. CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Shift Concerns, No 3-4 Shift/Harsh/Soft/Slipping. |
| P2705 | Transmission Friction Element "F" Apply Time Range/Performance | OWC faults (covers just the clutches) | DTC P2705 is a non-electrical DTC. CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Engagement Concerns, Neutral After Launch. |
| P2758 | Torque Converter Clutch Pressure Control Solenoid Stuck ON | TCC pressure control solenoid | DTC P2758 is a non-electrical DTC. Refer to: Diagnosis By Symptom . for Torque Converter Operation Concerns. |
| P2760 | Torque Converter Clutch Pressure Control Solenoid Intermittent | TCC pressure control solenoid | CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST H : DTCS P0740, P0742, P0743. P0744, P2760 |
| P2783 | Torque Converter Temperature Too High | Torque converter | TCC control valve stuck in the apply position. CLEAR the DTC. If the DTC returns, REFER to: Diagnosis By Symptom . for Torque Converter Operation Concerns, No Apply. |
| P2796 | Electric Transmission Fluid Pump Control Circuit | Electric transmission fluid pump control circuit | This DTC applies to auto-start-stop vehicles only. This DTC sets when the e-pump reports to the PCM that it is not receiving a PWM from the PCM. CLEAR the DTC. If the DTC returns, GO to PINPOINT TEST M : DTCS P0C2A:00, P0C2C:00, P0C2D:00, P0C2E:00, P2796:00 |