Touchscreen Display: ACM
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B1142:27 | Ignition Status 1: Signal Rate of Change Above Threshold | GO to Pinpoint Test G |
| B1A01:01 | Speaker #1: General Electrical Failure | For a LHF door midwoofer speaker concern, GO to Pinpoint Test H For a LHF door tweeter speaker concern, GO to Pinpoint Test I |
| B1A01:11 | Speaker #1: Circuit Short To Ground | For a LHF door midwoofer speaker concern, GO to Pinpoint Test H For a LHF door tweeter speaker concern, GO to Pinpoint Test I |
| B1A01:12 | Speaker #1: Circuit Short To Battery | For a LHF door midwoofer speaker concern, GO to Pinpoint Test H For a LHF door tweeter speaker concern, GO to Pinpoint Test I |
| B1A01:13 | Speaker #1: Circuit Open | GO to Pinpoint Test H |
| B1A02:01 | Speaker #2: General Electrical Failure | For a RHF door tweeter speaker concern, GO to Pinpoint Test K For a RHF Door Midwoofer Speaker concern, GO to Pinpoint Test L |
| B1A02:11 | Speaker #2: Circuit Short To Ground | For a RHF door tweeter speaker concern, GO to Pinpoint Test K For a RHF Door Midwoofer Speaker concern, GO to Pinpoint Test L |
| B1A02:12 | Speaker #2: Circuit Short To Battery | For a RHF door tweeter speaker concern, GO to Pinpoint Test K For a RHF Door Midwoofer Speaker concern, GO to Pinpoint Test L |
| B1A02:13 | Speaker #2: Circuit Open | GO to Pinpoint Test L |
| B1A03:01 | Speaker #3: General Electrical Failure | For a RHR door full-range speaker concern, GO to Pinpoint Test M For a RHR quarter panel mid-range speaker concern, GO to Pinpoint Test N |
| B1A03:11 | Speaker #3: Circuit Short To Ground | For a RHR door full-range speaker concern, GO to Pinpoint Test M For a RHR quarter panel mid-range speaker concern, GO to Pinpoint Test N |
| B1A03:12 | Speaker #3: Circuit Short To Battery | For a RHR door full-range speaker concern, GO to Pinpoint Test M For a RHR quarter panel mid-range speaker concern, GO to Pinpoint Test N |
| B1A03:13 | Speaker #3: Circuit Open | For a RHR door full-range speaker concern, GO to Pinpoint Test M For a RHR quarter panel mid-range speaker concern, GO to Pinpoint Test N |
| B1A04:01 | Speaker #4: General Electrical Failure | For a LHR door full-range speaker concern, GO to Pinpoint Test P For a LHR quarter panel mid-range speaker concern, GO to Pinpoint Test O |
| B1A04:11 | Speaker #4: Circuit Short To Ground | For a LHR door full-range speaker concern, GO to Pinpoint Test P For a LHR quarter panel mid-range speaker concern, GO to Pinpoint Test O |
| B1A04:12 | Speaker #4: Circuit Short To Battery | For a LHR door full-range speaker concern, GO to Pinpoint Test P For a LHR quarter panel mid-range speaker concern, GO to Pinpoint Test O |
| B1A04:13 | Speaker #4: Circuit Open | For a LHR door full-range speaker concern, GO to Pinpoint Test P For a LHR quarter panel mid-range speaker concern, GO to Pinpoint Test O |
| B1A06:01 | Speaker #6: General Electrical Failure | GO to Pinpoint Test J |
| B1A06:02 | Speaker #6: General Signal Failure | GO to Pinpoint Test J |
| B1A56:21 | Antenna: Signal Amplitude < Minimum | If DTC B1A56:21 sets after running the bezel diagnostic tests, DISREGARD this DTC. This test is used for end of line or repair bay testing at the Ford plant. Each plant has its own assigned frequency and signal strength requirements. The running and passing of this test depends on local radio stations. If no local station is broadcasting on the required frequency, the test will fail. |
| B1A89:11 | Satellite Antenna: Circuit Short To Ground | For a satellite radio concern, GO to Pinpoint Test B For a SIRIUS Data Services concern, GO to Pinpoint Test C |
| B1A89:13 | Satellite Antenna: Circuit Open | For a satellite radio concern, GO to Pinpoint Test B For a SIRIUS Data Services concern, GO to Pinpoint Test C |
| B1D19:49 | Compact Disc Unit: Internal Electronic Failure | CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC B1D19:49 is retrieved again, INSTALL a new ACM. Refer to: Audio Front Control Module (ACM) . |
| B1D19:4B | Compact Disc Unit: Over Temperature | The ACM was over temperature. This may occur during extended use. Audio operation can resume after the ACM cools. CLEAR the DTC. This is normal operation. |
| U0100:00 | Lost Communication With ECM/ PCM "A": No Sub Type Information | GO to Pinpoint Test AE |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AF |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AH |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AM |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to Pinpoint Test AN |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | This DTC sets due to an incorrect or incomplete ACM configuration. Using a diagnostic scan tool, PERFORM the ACM programming procedure using as-built data. For information on as-built data, Refer to: Module Configuration - System Operation and Component Description . See As-Built Data. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC sets due to an incorrect or incomplete ACM configuration. Using a diagnostic scan tool, PERFORM the ACM programming procedure using as-built data. For information on as-built data, Refer to: Module Configuration - System Operation and Component Description . See As-Built Data. |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | This DTC sets due to an incorrect or incomplete ACM configuration. Using a diagnostic scan tool, PERFORM the ACM programming procedure using as-built data. For information on as-built data, Refer to: Module Configuration - System Operation and Component Description . See As-Built Data. |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new ACM. Refer to: Audio Front Control Module (ACM) . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:42 is retrieved again, INSTALL a new ACM. Refer to: Audio Front Control Module (ACM) . |
| U3000:96 | Control Module: Component Internal Failure | CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:96 is retrieved again, INSTALL a new ACM. Refer to: Audio Front Control Module (ACM) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AO |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AP |