Common Specifications & Procedures
ESCAPE & MARINER - COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | GENERAL SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front Hub Nut | 222 Ft. Lbs. (300 N.m) | ||
| Rear Hub Nut | 222 Ft. Lbs. (300 N.m) | ||
| Battery | BATTERY AND CABLES | ||
| Brakes | |||
| Bleeding Sequence | BRAKE SYSTEM BLEEDING | ||
| Disc/Drum Brakes w/Torque | |||
| Front Disc | SPECIFICATIONS | ||
| Rear Drum | SPECIFICATIONS | ||
| Charging | |||
| Generator w/Torque | SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | |||
| 2.5L | BELT TENSIONER | ||
| 3.0L (4V) | BELT TENSIONER | ||
| Belt Routing | |||
| 2.5L | ACCESSORY DRIVE BELT ROUTING | ||
| 3.0L (4V) | ACCESSORY DRIVE BELT ROUTING | ||
| Engine Cooling | |||
| General Service Specifications | GENERAL SPECIFICATIONS | ||
| Radiator Cap Pressure | |||
| 2.5L | 17.4-21.7 psi (120-150 kPa) | ||
| 3.0L (4V) | 25 psi (172 kPa) Minimum at 1,500 RPM with engine warmed up after 10 minutes of idling | ||
| Thermostat R & I | |||
| 2.5L | THERMOSTAT HOUSING -- 2.5L | ||
| 3.0L (4V) | THERMOSTAT -- 3.0L (4V) | ||
| Water Pump R & I | |||
| 2.5L | COOLANT PUMP -- 2.5L | ||
| 3.0L (4V) | COOLANT PUMP -- 3.0L (4V) | ||
| Engine Mechanical | |||
| 2.5L | |||
| Compression | COMPRESSION TEST -- ALL VEHICLES EXCEPT HYBRID | ||
| Oil Pressure (hot @ 2,000 RPM) | 29-39 psi (200-268 kPa) | ||
| Overhaul | GENERAL SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 3.0L (4V) | |||
| Compression | COMPRESSION TEST -- ALL VEHICLES EXCEPT HYBRID | ||
| Oil pressure (Minimum at 1,500 RPM with engine warmed up after 10 minutes of idling) | 25 psi (172 kPa) | ||
| Overhaul | GENERAL SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate Torque | |||
| 2.5L | Stage 1: 37 Ft. Lbs. (50 N.m) Stage 2: 59 Ft. Lbs. (80 N.m) Stage 3: 83 Ft. Lbs. (112 N.m) |
||
| 3.0L | 59 Ft. Lbs. (80 N.m) | ||
| Fuel System | |||
| Fuel Filter Location | Lifetime fuel filter (serviced as part of the Fuel Pump module). | ||
| Fuel Filter R & I | FUEL PUMP MODULE | ||
| Pressure Release Procedure | FUEL SYSTEM PRESSURE RELEASE | ||
| Pressure Specification | FUEL PRESSURE -- CARS | ||
| Fuel Pressure Test Procedure | FUEL SYSTEM PRESSURE TEST | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Spark Plugs | |||
| 2.5L | |||
| Type | Motorcraft AYSF-32-YPC | ||
| Gap | 1.25-1.35 mm (0.049-0.053 in) | ||
| Torque | 106 In. Lbs. (12 N.m) | ||
| 3.0L | |||
| Type | Moorcraft CGSF-22N | ||
| Gap | 1.15-1.25 mm (0.045-0.049 in) | ||
| Torque | 133 In. lbs (15 N.m) | ||
| Starting | |||
| Starter w/Torque | SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | ALIGNMENT SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 100 Ft. Lbs. (135 N.m) | ||