Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Ford >> 2010 >> Taurus SE >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 1 (Engine Mechanical - 3.5L GTDI) >> Specifications >> Torque Specifications

Torque Specifications

WARNING: This page is about a different variant/trim than selected.
TORQUE SPECIFICATIONS

Description Nm lb-ft lb-in
A/C compressor bolts and nut 25 18 -
A/C compressor stud 9 - 80
A/C tube bracket bolt 15 - 133
A/C tube nut 15 - 133
A/C tube retaining clamp bolt 9 - 80
A/C tube-to-compressor nut 15 - 133
A/C tube bracket-to-compressor bolt 25 18 -
Accessory drive belt tensioner bolts 11 - 97
Ball joint nuts 200 148 -
Battery cable power feed cable nut 6 - 53
Block drain plug - RH 40 30 -
Block drain plug - LH(1) - - -
Block heater 40 30 -
Charge Air Cooler (CAC) tube clamps 5 - 44
CAC  outlet pipe clamps 5 - 44
Camshaft bearing cap bolts(2) - - -
Camshaft Position (CMP) sensor bolts 10 - 89
Connecting rod cap bolts(2) - - -
Coolant pump bolts(2) - - -
Crankcase rear seal retainer plate bolts(2) - - -
Crankshaft Position (CKP) sensor bolt 10 - 89
Crankshaft pulley bolt(2) - - -
Cylinder head bolts(2) - - -
Cylinder head M6 bolt 10 - 89
Cylinder Head Temperature (CHT) sensor 10 - 89
Driveshaft-to-Power Transfer Unit (PTU) bolts 70 52 -
Electronic Power Assist Steering (EPAS) wiring retainer bolt 9 - 80
Engine cover mounting stud 6 - 53
Engine front cover bolts(2) - - -
Engine lifting eye bolts 24 18 -
Engine mount studs(2) - - -
Engine mount-to-engine nuts 63 46 -
Engine mount-to-frame bolts 90 66 -
Engine oil filter(3) - - -
Engine Oil Pressure (EOP) switch 18 - 159
Engine-to-transaxle bolts 48 35 -
Exhaust camshaft bolt(2) - - -
Exhaust manifold heat shield bolts 14 - 124
Exhaust manifold nuts(2) - - -
Exhaust manifold studs 12 - 106
Exhaust manifold-to-turbocharger bolts 45 33 -
Flexplate bolts 80 59 -
Front halfshaft nut 350 258 -
Fuel injection pump bolts(2) - - -
Fuel rail bolts(2) - - -
Fuel tube bracket-to-engine front cover bolt 10 - 89
Generator bolt and nut 47 35 -
Generator B+ terminal nut 17 - 150
Generator stud 8 - 71
Ground cable-to-negative battery cable nut 6 - 53
Ground cable-to-cylinder head bolt 10 - 89
Ground wire-to-engine front cover bolt 10 - 89
Halfshaft support bracket bolts 40 30 -
Heated Oxygen Sensor (HO2S) bracket-to-engine front cover bolt 10 - 89
Heat shield nut 10 - 89
High pressure fuel tube bolt 6 - 53
High pressure fuel tube flare nut 30 22 -
High pressure fuel tube nut 6 - 53
Ignition coil-on-plug bolts 7 - 62
Intake manifold bolts(2) - - -
Intermediate and halfshaft assembly bolts 25 18 -
Intermediate steering shaft bolt 20 - 177
Knock Sensor (KS) bolts 20 - 177
Main bearing bolts(2) - - -
Main bearing cap support brace bolts(2) - - -
Oil filter adapter bolts 10 - 89
Oil pan bolts(2) - - -
Oil pan drain plug 27 20 -
Oil pan-to-transaxle bolts 48 35 -
Oil pump bolts 10 - 89
Oil pump screen and pickup tube bolts 10 - 89
Oil supply tube bracket-to-valve cover stud bolt nut 8 - 71
Power Transfer Unit (PTU) bolts 70 52 -
PTU  support bracket bolts(2) - - -
Radio capacitor bolt 10 - 89
RH brake hose bracket bolt 30 22 -
RH CAC  tube nut 6 - 53
RH turbocharger intake pipe clamp 6 - 53
RH turbocharger intake tube nut 6 - 53
Roll restrictor bolts 90 66 -
Secondary timing exhaust camshaft bolt(2) - - -
Secondary timing Variable Camshaft Timing (VCT) bolt(2) - - -
Secondary timing chain tensioner bolts 10 - 89
Spark plugs 15 - 133
Stabilizer bar link nuts 150 111 -
Starter bolt and stud bolt 27 20 -
Starter B+ terminal nut 12 - 106
Starter S-terminal nut 5 - 44
Strut tower brace nuts 30 22 -
Subframe bracket bolts 55 41 -
Subframe - front bolts 200 148 -
Subframe - rear bolts 150 111 -
Thermostat housing bolts 10 - 89
Tie-rod end nuts 150 111 -
Timing chain guide bolts 10 - 89
Timing chain tensioner bolts 10 - 89
Torque converter-to-flexplate bolts 55 41 -
Transaxle support insulator bracket-to-transaxle bolt 80 59 -
Transaxle support insulator bracket-to-transaxle nuts 63 46 -
Transaxle-to-engine bolts 48 35 -
Turbocharger coolant tube banjo bolts 37 27 -
Turbocharger coolant tube bracket-to-cylinder head bolt 10 - 89
Turbocharger intake tube clamp 5 - 44
Turbocharger intake tube-to-RH valve cover nut 6 - 53
Turbocharger oil return tube bolts 10 - 89
Turbocharger oil supply quick connect fitting 16 - 142
Turbocharger oil supply tube banjo bolts 35 26 -
Turbocharger-to-cylinder block bolts(2) - - -
Turbocharger-to-exhaust manifold bolts 45 33 -
Turbocharger-to- turbocharger bracket bolts(2) - - -
Upper stabilizer bar link nuts 150 111 -
Valve cover stud bolts(2) - - -
Variable Camshaft Timing (VCT) housing bolts(2) - - -
VCT  bolt(2) - - -
VCT  solenoid bolts 10 - 89
Wheel hub nuts 350 258 -
Wiring harness retainer stud bolt 10 - 89
(1) Tighten to 20 Nm (177 lb-in) plus an additional 180 degrees.
(2) Refer to the appropriate procedure(s).
(3) Tighten to 5 Nm (44 lb-in) plus an additional 180 degrees.
scientia non olet · About Mike's Workshop Manuals