Common Specs & Procedures
RAM PROMASTER CITY COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | Refer to A/C SYSTEM | ||
| Torque | Refer to TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | Refer to REMOVAL AND INSTALLATION | ||
| Rear | N/A | ||
| Battery | Refer to BATTERY | ||
| Brakes | |||
| Bleeding Sequence | Refer to STANDARD PROCEDURE | ||
| Disc Brakes | |||
| Service Specifications | Refer to ROTOR, BRAKE
.
NOTE:
Specifications not available from the manufacturer.
|
||
| Torque | Base Brakes: refer to SPECIFICATIONS , Antilock Brakes: refer to SPECIFICATIONS | ||
| Drum Brakes | |||
| Service Specifications | Refer to DRUM, BRAKE
NOTE:
Specifications not available from the manufacturer.
|
||
| Torque | Refer to SPECIFICATIONS | ||
| Charging | |||
| Generator | Refer to GENERATOR | ||
| Torque | Refer to TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Serpentine belt used, not adjustable. | ||
| Drive Belt Routing | Refer to appropriate "Belt Routing" figure under REMOVAL AND INSTALLATION . | ||
| Engine Cooling | |||
| General Service Specifications | Refer to SPECIFICATIONS | ||
| Radiator Cap Pressure | 16 to 20 psi (110 to 138 kPa) | ||
| Thermostat R & I | Refer to THERMOSTAT | ||
| Water Pump R & I | Refer to PUMP, WATER | ||
| Engine Mechanical | |||
| 2.4L | |||
| Compression | Compression should not be less than 689 kPa (100 psi) and not vary more than 25 percent from cylinder to cylinder. | ||
| Oil pressure | Refer OIL PRESSURE table under ENGINE SPECIFICATIONS . | ||
| Overhaul | Refer to ENGINE SPECIFICATIONS | ||
| Torque | Refer to TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| 2.4L | 21 ft. lbs. + 51° (29 N.m + 51°) | ||
| Fuel System | |||
| Pressure Specification | 58 psi ± 5 psi (400 kPa ± 34 kPa) | ||
| Fuel Pressure Test Procedure | Refer to CHECKING THE FUEL DELIVERY SYSTEM (HARD START) | ||
| Fuel Filter Location | Fuel filter is part of fuel pump module. | ||
| Fuel Filter R & I | Refer to MODULE, FUEL PUMP | ||
| Ignition | |||
| Firing Order & Cylinder Identification | Refer to FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| 2.4L | |||
| Type | REC10WMPB4 | ||
| Gap | .047 in. (1.2 mm) | ||
| Torque | 20 ft. lbs. (27 N.m). | ||
| Starting | |||
| Starter | Refer to STARTING - SERVICE INFORMATION
NOTE:
Information not available from the manufacturer
|
||
| Torque | Refer to TORQUE | ||
| Wheel Alignment | |||
| Adjustment Specifications | Refer to SPECIFICATIONS | ||
| Torque | Refer to TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | Aluminum: 89 ft. lbs. (120 N.m) Steel: 64 ft. lbs. (86 N.m) |
||