Diagnostic Test

1. With the scan tool, read the OCM DTC.

   Does the scan tool display any active DTC relating to internal faults, ignition faults, or battery faults?

   Yes 

   • Perform the appropriate DTC. See DTC-Based Diagnostics/MODULE, Occupant Classification (OCM) - Diagnosis and Testing .

   No 

   • Go to step  2

Does the scan tool display active: B1B8E-DRIVER SEAT TRACK POSITION SENSOR CIRCUIT HIGH DTC?

Yes 

• Go to step  3

No 

• Perform the RESTRAINTS SYSTEM INTERMITTENT TEST. Refer to DTC-Based Diagnostics/CONTROLLER, Occupant Restraint (ORC) - Standard Procedure .

Courtesy of CHRYSLER LLC

1. Disconnect the Driver Seat Track Position Sensor connector.
2. Disconnect the OCM C1 connector.
   WARNING: Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
3. Measure the (R261) Driver Seat Position Sensor Data circuit voltage between the Driver Seat Position Sensor connector cavity 1 and ground.
4. Measure the (R263) Driver Seat Position Sensor Voltage circuit voltage between the Driver Seat Position Sensor connector cavity 2 and ground.

   Is there voltage present on either circuit?

   Yes 

   • Go to step  4

   No 

   • Go to step  6

Courtesy of CHRYSLER LLC

1. Disconnect the C311 body harness to Passenger Seat connector.
2. Measure the (R261) Driver Seat Position Sensor Data circuit voltage between the Driver Seat Position Sensor connector cavity 1 and ground.
3. Measure the (R263) Driver Seat Position Sensor Voltage circuit voltage between the Driver Seat Position Sensor connector cavity 2 and ground.

   Is there any voltage present on either circuit?

   Yes 

   • Go to step  5

   No 

   NOTE: Do not attempt to repair the seat wiring.
   • Replace the Passenger seat wiring in accordance with the Service Information.
   • Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to DTC-Based Diagnostics/CONTROLLER, Occupant Restraint (ORC) - Standard Procedure .

Courtesy of CHRYSLER LLC

1. Disconnect the C310 body harness to Driver Seat connector.
2. Measure the (R261) Driver Seat Position Sensor Data circuit voltage between the Driver Seat Position Sensor connector cavity 1 and ground.
3. Measure the (R263) Driver Seat Position Sensor Voltage circuit voltage between the Driver Seat Position Sensor connector cavity 2 and ground.

   Is there any voltage present on either circuit?

   Yes 

   NOTE: Do not attempt to repair the seat wiring.
   • Replace the Driver seat wiring in accordance with the Service Information.
   • Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to DTC-Based Diagnostics/CONTROLLER, Occupant Restraint (ORC) - Standard Procedure .

   No 

   NOTE: Do not attempt to repair the seat wiring.
   • Replace the Body Harness between the Driver and Passenger Seat in accordance with the Service Information.
   • Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to DTC-Based Diagnostics/CONTROLLER, Occupant Restraint (ORC) - Standard Procedure .

1. Replace the Driver Seat Track Position Sensor.
2. Reconnect all disconnected components except the battery.
   WARNING: Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
3. Connect the scan tool to the Data Link Connector - use the most current software available.
4. Use the scan tool and erase all codes in the OCM.
5. Turn the Ignition Off, and wait 15 seconds before turning the Ignition On.
6. Wait one minute, and read active codes.

   Did the active B1B8E-DRIVER SEAT TRACK POSITION SENSOR CIRCUIT HIGH DTC return?

   Yes 

   WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure to take the proper precautions can result in accidental airbag deployment and serious or fatal injury.
   WARNING: Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.
   CAUTION: Disconnecting or connecting the OCM connectors with the battery connected permanently damages the OCM.
   • Replace the OCM in accordance with the Service Information.
   • Perform the OCM REZERO. Refer to DTC-Based Diagnostics/CONTROLLER, Occupant Restraint (ORC) - Standard Procedure .

   No 

   • Repair is complete.
   • Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Refer to DTC-Based Diagnostics/CONTROLLER, Occupant Restraint (ORC) - Standard Procedure .