Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Dodge and Ram >> 2003 >> Durango Base, 4.7 N, 4WD, Part Time >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls - Self-Diagnostics - 4.7L >> Diagnostic Tests >> DTC P0579: Speed Control Switch #1 Performance >> Testing

DTC P0579: Speed Control Switch #1 Performance: Testing

  1. Start the engine. With the DRBIII® scan tool, monitor each switch junction for the speed control switches. Press and release each speed control button, (Resume/Accel - Cancel - Decel (Coast) - On/Off - Set). Does each switch function change status when pressing and then depressing each switch? If yes, see INTERMITTENT CONDITION  under SELF-DIAGNOSTIC SYSTEM. If no, go to next step.
  2. Turn the ignition off. Remove the speed control switches from the steering wheel. Measure the resistance across each switch control switch. Monitor the ohmmeter while pressing each function button on each switch. Resume/Accel (15,400 ohms), Cancel (900-918 ohms), Decel (Coast) (2910-2970 ohms), On/Off (0 ohm), Set (6584-6716 ohms). Does the function on the speed control switches have the correct ohm value? If yes, go to next step. If no, replace the speed control switch that had the incorrect resistance value.
  3. Disconnect the PCM harness connectors. Measure the resistance between the (V37) S/C switch signal circuit and the (K4) sensor ground circuit in the speed control harness connector. Is the resistance below 5.0 ohms? If yes, repair the (V37) S/C switch signal circuit shorted to the (K4) sensor ground circuit. If no, go to next step.
  4. Measure the resistance between ground and the (V37) S/C switch signal circuit at the speed control harness connector. Is the resistance below 100 ohms? If yes, repair the (V37) speed control switch signal circuit shorted to the ground. If no, go to next step.
  5. Measure the voltage of the (V37) speed control switch signal circuit at the speed control harness connector. Is the is the voltage above 5.0 volts? If yes, repair the (V37) S/C switch signal circuit shorted to the battery voltage. If no, go to next step.
    6. CAUTION: Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals resulting in poor terminal to pin connection. Install Miller Special Tool (8815) to perform diagnosis.
  6. The measurement must be taken from both speed control switch harness connectors. Measure the resistance of the (V37) S/C switch signal circuit from the speed control harness connector to the appropriate terminal of Miller Special Tool (8815). Is the resistance below 5.0 ohms for both measurements? If yes, go to next step. If no, repair the (V37) speed control switch signal circuit for an open.
    7. CAUTION: Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals resulting in poor terminal to pin connection. Install Miller Special Tool (8815) to perform diagnosis.
  7. The measurement must be taken from both speed control switch harness connectors. Measure the resistance of the (K4) sensor ground circuit from the speed control harness connector to the appropriate terminal of Miller Special Tool (8815). Is the resistance below 5.0 ohms for both measurements? If yes, go to next step. If no, repair the (K4) sensor ground circuit for an open.
    8. NOTE: Before continuing, disconnect the PCM harness connectors and check the related wiring terminals for corrosion, damage or terminal push out. Repair as necessary.
  8. Using the wiring diagram as a guide, inspect the wire harness and connectors. Visually inspect the related wire harness. Look for any chafed, pierced, pinched, or partially broken wires. Visually inspect both the component and the PCM connectors. Pay particular attention to all power and ground circuits. If there are no possible causes remaining, replace and program the PCM. See PROGRAMMING .
scientia non olet · About Mike's Workshop Manuals