Common Specs & Procedures
300 & CHARGER COMMON SPECS & PROCEDURES
| System | Specification/Procedure | |||
|---|---|---|---|---|
| Air Conditioning | ||||
| Service | A/C SYSTEM | |||
| Torque | TORQUE | |||
| Axle Nut/Hub Nut | ||||
| Front | ||||
| AWD | 213 N.m (157 Ft. Lbs.) | |||
| RWD | 250 N.m (184 Ft. Lbs.) | |||
| Rear | 213 N.m (157 ft. lbs.) | |||
| Battery | BATTERY | |||
| Brakes | ||||
| Bleeding Sequence | ||||
| ABS | BLEEDING | |||
| BASE | BASE BRAKE BLEEDING | |||
| SRT8 | BASE BRAKE BLEEDING - SRT8 | |||
| Disc Brakes | ||||
| Service Specifications | See appropriate text under the BASE - SERVICE INFORMATION article | |||
| Torque | Base BRAKE FASTENER TORQUE ABS TORQUE | |||
| Charging | ||||
| Generator | GENERATOR | |||
| Torque | TORQUE | |||
| Drive Belts | ||||
| Adjustment | TENSIONER, Belt | |||
| Drive Belt Routing | See appropriate figure under Removal & Installation . | |||
| Engine Cooling | ||||
| General Service Specifications | SPECIFICATIONS | |||
| Radiator Cap Pressure | 16-20 psi | |||
| Thermostat R & I | THERMOSTAT | |||
| Water Pump R & I | PUMP, WATER | |||
| Engine Mechanical | ||||
| 2.7L | ||||
| Compression | CYLINDER COMPRESSION PRESSURE TEST | |||
| Oil Pressure | See Oil Pressure table under Specifications | |||
| Overhaul | 2.7L ENGINE | |||
| Torque | TORQUE | |||
| 3.5L | ||||
| Compression | CYLINDER COMPRESSION PRESSURE TEST | |||
| Oil Pressure | See Oil Pressure table under Specifications | |||
| Overhaul | 3.5L ENGINE | |||
| Torque | TORQUE - 3.5L | |||
| 5.7L | ||||
| Compression | CYLINDER COMPRESSION PRESSURE LEAKAGE | |||
| Oil Pressure | See Oil Pressure table under SPECIFICATIONS | |||
| Overhaul | SPECIFICATIONS | |||
| Torque | TORQUE | |||
| 6.1L | ||||
| Compression | CYLINDER COMPRESSION PRESSURE | |||
| Oil Pressure | See Oil Pressure table under SPECIFICATIONS | |||
| Overhaul | SPECIFICATIONS | |||
| Torque | TORQUE | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | |||
| Flywheel/Flex Plate/Drive Plate Torque | ||||
| 2.7L | 95 N.m (70 ft. lbs.) | |||
| 3.5L | 95 N.m (70 ft. lbs.) | |||
| 5.7L | 95 N.m (70 ft. lbs.) | |||
| 6.1L | 95 N.m (70 ft. lbs.) | |||
| Fuel System | ||||
| Pressure Specification | 400 kPa ±34 kPa (58 psi ± 5 psi) | |||
| Fuel Pressure Test Procedure | Standard Procedure | |||
| Fuel Filter Location | N/A | |||
| Fuel Filter R & I | N/A | |||
| Ignition | ||||
| Firing Order & Cylinder Identification | ||||
| 2.7L | 1-2-3-4-5-6: For cylinder identification, FIRING ORDER & CYLINDER IDENTIFICATION . | |||
| 3.5L | 1-2-3-4-5-6: For cylinder identification, FIRING ORDER & CYLINDER IDENTIFICATION . | |||
| 5.7L | 1-8-4-3-6-5-7-2: For cylinder identification, FIRING ORDER & CYLINDER IDENTIFICATION . | |||
| 6.1L | 1-8-4-3-6-5-7-2: For cylinder identification, see FIRING ORDER & CYLINDER IDENTIFICATION . | |||
| Ignition Coil (Resistance) | ||||
| Standard value | ||||
| 2.7L, 3.0L, 3.5L, 5.7L | N/A | |||
| 6.1L | IGNITION COIL RESISTANCE | |||
| Ignition Wires (Routing) | N/A | |||
| Spark Plug | ||||
| Type | ||||
| 2.7L | TE10PMC5 | |||
| 3.5L | ZFR5LP13G | |||
| 5.7L | LZFR5C-11 | |||
| 6.1L | PLZTR5A-13 | |||
| Gap | ||||
| 2.7L | 1.30 mm (0.051 in) | |||
| 3.5L | 1.30 mm (0.051 in.) | |||
| 5.7L | 1.00 mm (0.040 in.) | |||
| 6.1L | 1.30 mm (0.051 in.) | |||
| Torque | ||||
| 2.7L | 17.5 N.m (13 Ft. Lbs.) | |||
| 3.5L | 27 N.m (20 Ft. Lbs.) | |||
| 5.7L | 17.5 N.m (13 Ft. Lbs.) | |||
| 6.1L | 17.5 N.m (13 Ft. Lbs.) | |||
| Starting | ||||
| Starter | STARTER MOTOR | |||
| Torque | TORQUE | |||
| Wheel Alignment | ||||
| Adjustment Specifications | WHEEL ALIGNMENT | |||
| Torque | For front, refer to FRONT SUSPENSION FASTENER TORQUE . For rear, refer to REAR SUSPENSION FASTENER TORQUE . | |||
| Wheel & Tire | ||||
| Wheel Lug Nut Torque | ||||
| Base | 150 N.m (110 Ft. Lbs.) | |||
| Police Package | 190 N.m (140 Ft. Lbs.) | |||