Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Chrysler >> 2010 >> 300 C, AWD >> Repair and Diagnosis >> Engine Performance >> System >> DRIVEABILITY - Non-DTC Diagnostics >> Diagnosis And Testing >> Checking The Charging System Performance >> Diagnostic Test

Diagnostic Test

  1. GENERATOR FULL FIELD TEST 
    NOTE: Diagnose and repair any generator sense or field control circuit DTCs before proceeding with this test.
    1. Start the engine and allow it to reach normal operating temperature.
      WARNING: When the engine is operating, do not stand in direct line with the fan. Do not put your hand near the pulleys, belts, or fan. Do not wear loose clothing. Failure to follow these instructions can result in possible serious or fatal injury.
    2. With the scan tool, perform the Generator Full Field test. Follow the instructions displayed on the scan tool.
    3. Monitor the system (battery) voltage and the generator sense voltage on the scan tool while performing the test.
      NOTE: With the engine running, the difference between the system (battery) voltage and the generator sense voltage should be below 0.2 volts.
      NOTE: With the generator field fully actuated, the system (battery) voltage should be above 14.0 volts.
      NOTE: With the generator field actuated off, the system (battery) voltage should be below 13.0 volts, and eventually drop as battery load is increased.

      Did the system voltage change as described above during the Generator Full Field test?

      Yes 

      • Test complete.

      No 

      • Go to step  2
  2. CHARGING SYSTEM INSPECTION 
    1. Inspect and test the battery in accordance with the Service Information.
    2. Inspect the generator drive belt for proper alignment and adjustment.
    3. Inspect the vehicle for aftermarket accessories that may exceed the generator system output.
    4. Inspect the fuses in the PDC and TIPM. If an open fuse is found, use the wiring diagram/schematics as a guide and inspect the wiring and connectors for a damaged or shorted circuit.

      Were any problems found?

      Yes 

      • Repair as necessary.

      No 

      • Go to step  3
  3. BATTERY POSITIVE (+) CIRCUIT HIGH RESISTANCE 
    NOTE: Make sure all testing equipment and cables are clear of any engine parts before starting the engine.
    1. Start the engine.
      WARNING: When the engine is operating, do not stand in direct line with the fan. Do not put your hand near the pulleys, belts, or fan. Do not wear loose clothing. Failure to follow these instructions can result in possible serious or fatal injury.
    2. Measure the voltage between the B (+) Terminal at the Generator and the Battery Positive (+) Post.

      Is the voltage below 0.4 volts?

      Yes 

      • Go to step  4

      No 

      • Repair the battery positive (+) circuit between the generator and battery for high resistance.
      • Perform the PCM VERIFICATION TEST. Refer to PCM VERIFICATION TEST .
  4. GENERATOR CASE GROUND HIGH RESISTANCE 
    NOTE: Make sure all testing equipment and cables are clear of any engine parts before starting the engine.
    1. Start the engine.
      WARNING: When the engine is operating, do not stand in direct line with the fan. Do not put your hand near the pulleys, belts, or fan. Do not wear loose clothing. Failure to follow these instructions can result in possible serious or fatal injury.
    2. Measure the voltage between the Generator case and the Battery Negative (-) post.

      Is the voltage below 0.1 volt?

      Yes 

      • Go to step  5

      No 

      • Repair the Generator Case ground for high resistance.
      • Perform the PCM VERIFICATION TEST. Refer to PCM VERIFICATION TEST .
  5. GENERATOR 
    Fig 1: Checking Generator Field Control Circuit
    GC0097578Courtesy of CHRYSLER LLC
    1. Turn the ignition off.
    2. Disconnect the Generator harness connector.
    3. Connect a 12-volt test light connected between the (A804) Gen Sense circuit and the (K20) Gen Field Control circuit in the Generator harness connector.
    4. Turn the ignition on.
    5. With the scan tool, actuate the Alternator Field Control State to toggle.
      NOTE: The test light should toggle on and off with the actuation.
      NOTE: If a DTC is active, the actuation test may not be allowed by the PCM. It may be necessary to clear DTCs before starting the actuation.

      Does the test light illuminate on and off with the actuation?

      Yes 

      • Replace the Generator in accordance with the Service Information.
      • Perform the PCM VERIFICATION TEST. Refer to PCM VERIFICATION TEST .

      No 

      • Go to step  6
  6. (K20) GEN FIELD CONTROL CIRCUIT SHORTED TO VOLTAGE 
    Fig 2: Checking Generator Field Control Circuit For Short To Voltage
    GC0097575Courtesy of CHRYSLER LLC
    1. Turn the ignition off.
    2. Disconnect the Powertrain Control Module (PCM) connector.
    3. Turn the ignition on.
    4. Measure the voltage of the (K20) Gen Field Control circuit in the Generator harness connector.

      Is there any voltage present?

      Yes 

      • Repair the (K20) Gen Field Control circuit for a short to voltage.
      • Perform the PCM VERIFICATION TEST. Refer to PCM VERIFICATION TEST .

      No 

      • Go to step  7
  7. (K20) GEN FIELD CONTROL CIRCUIT SHORTED TO GROUND 
    Fig 3: Checking Generator Field Control Circuit For Short To Ground
    GC0097576Courtesy of CHRYSLER LLC
    1. Turn the ignition off.
    2. Measure the resistance between the ground and the (K20) Gen Field Control circuit in the Generator harness connector.

      Is the resistance below 100 ohms?

      Yes 

      • Repair the (K20) Gen Field Control circuit for a short to ground.
      • Perform the PCM VERIFICATION TEST. Refer to PCM VERIFICATION TEST .

      No 

      • Go to step  8
  8. (K20) GEN FIELD CONTROL CIRCUIT OPEN OR HIGH RESISTANCE 
    Fig 4: Checking Generator Field Control Circuit For Open Or High Resistance
    GC0097577Courtesy of CHRYSLER LLC
    CAUTION: Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals, resulting in poor terminal to pin connection. Install the PCM Pinout Box 8815 to perform diagnosis.
    1. Measure the resistance of the (K20) Gen Field Control circuit between the Generator harness connector and the appropriate terminal of special tool #8815.

      Is the resistance below 5.0 ohms?

      Yes 

      • Go to step  9

      No 

      • Repair the (K20) Gen Field Control circuit for an open circuit or high resistance.
      • Perform the PCM VERIFICATION TEST. Refer to PCM VERIFICATION TEST .
  9. (A804) GEN SENSE CIRCUIT OPEN OR HIGH RESISTANCE 
    Fig 5: Checking Generator Sense Circuit For Open Or High Resistance
    GC0097574Courtesy of CHRYSLER LLC
    CAUTION: Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals, resulting in poor terminal to pin connection. Install the PCM Pinout Box 8815 to perform diagnosis.
    1. Measure the resistance of the (A804) Gen Sense circuit between the Generator harness connector and the appropriate terminal of special tool #8815.

      Is the resistance below 5.0 ohms?

      Yes 

      • Go to step  10

      No 

      • Repair the (A804) Gen Sense circuit for an open circuit or high resistance.
      • Perform the PCM VERIFICATION TEST. Refer to PCM VERIFICATION TEST .
  10. POWERTRAIN CONTROL MODULE (PCM) 
    1. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Generator and the Powertrain Control Module (PCM).
    2. Look for any chafed, pierced, pinched, or partially broken wires.
    3. Look for broken, bent, pushed out or corroded terminals.
    4. Refer to any Technical Service Bulletins that may apply.

      Were any problems found?

      Yes 

      No 

      • Replace and program the Powertrain Control Module (PCM) in accordance with the Service Information.
      • Perform the PCM VERIFICATION TEST. Refer to PCM VERIFICATION TEST .
scientia non olet · About Mike's Workshop Manuals