Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Chrysler >> 1999 >> Sebring Limited >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls - Tests W/Codes - Convertible >> Self-Diagnostic Tests >> DTC P0505: Idle Air Control Motor Circuits

DTC P0505: Idle Air Control Motor Circuits

NOTE: For connector terminal ID, see CONNECTOR IDENTIFICATION . For wiring diagram, see WIRING DIAGRAMS article.
NOTE: Idle air control motor circuits are monitored when ignition is on and battery voltage is more than 11.5 volts. DTC may be stored in Powertrain Control Module (PCM) when PCM senses a short to ground or battery voltage on any of the for idle air control motor driver circuits for 2.75 seconds while idle air control motor is operating. Possible causes are: defective PCM, defective idle air control motor, or defective connectors or wiring.
  1. Start engine and allow engine to idle for 20 seconds. If engine will not idle, hold throttle slightly open to keep the engine running.
  2. Using scan tool, actuate idle air control motor to 1400 RPM. Note if engine speed is 1300-1500 RPM. If engine speed is within specification, go to next step. If engine speed is not within specification, go to step  26.
  3. Turn ignition off. Start engine and allow engine to idle for 20 seconds. Using scan tool, actuate idle air control motor to 900 RPM. Note if engine speed is 800-1000 RPM. If engine speed is within specification, go to next step. If engine speed is not within specification, go to step  26.
  4. Turn ignition off. Start engine and allow engine to idle. Using scan tool in SYSTEM TESTS, perform IAC WIGGLE test. Idle speed should increase and then decrease in accordance with display on scan tool if idle air control motor is operating correctly. If idle air control motor operates correctly, go to next step. If idle air control motor does not operate correctly, go to step  7.
  5. Turn ignition off. Inspect wiring and connectors between idle air control motor and PCM. Idle air control motor is mounted on the throttle body and contains a 4-pin connector. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. If no problems exist, go to next step. If any problems exist, repair wiring or connectors as necessary. Perform TEST VER-5A .
  6. Start engine and allow engine to idle. Using scan tool in SYSTEM TESTS, perform IAC WIGGLE test. Wiggle wiring harness and connectors from idle air control motor to the PCM while observing operation of idle air control motor. If idle air control motor does not stop operating while wiggling wiring harness and connectors, test is complete. If idle air control motor stops operating while wiggling wiring harness and connectors, repair wiring or connectors as necessary. Perform TEST VER-5A .
  7. Turn ignition off. Inspect wiring and connectors between idle air control motor and PCM. Idle air control motor is mounted on the throttle body and contains a 4-pin connector. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. If no problems exist, go to next step. If any problems exist, repair wiring or connectors as necessary. Perform TEST VER-5A .
  8. Ensure ignition is off. Disconnect connector at idle air control motor. Start engine and allow engine to idle. Using voltmeter, check voltage at terminal No. 1 (Gray/Red wire) on connector for idle air control motor. If voltage is more than 5 volts at any time, go to next step. If voltage is not more than 5 volts at any time, go to step  20.
  9. Turn ignition off. Using ohmmeter, check resistance between ground and terminal No. 4 (Violet/Black wire) on connector for idle air control motor. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Violet/Black wire between PCM and idle air control motor. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. Perform TEST VER-5A .
  10. Using ohmmeter, check resistance between ground and terminal No. 1 (Gray/Red wire) on connector for idle air control motor. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Gray/Red wire between PCM and idle air control motor. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. Perform TEST VER-5A .
  11. Start engine and allow engine to idle. Using voltmeter, check voltage at terminal No. 2 (Yellow/Black wire) on connector for idle air control motor. If voltage is more than 5 volts at any time, go to next step. If voltage is not more than 5 volts at any time, go to step  15.
  12. Turn ignition off. Ensure connector is still disconnected at idle air control motor. Using ohmmeter, check resistance between ground and terminal No. 2 (Yellow/Black wire) on connector for idle air control motor. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Yellow/Black wire between PCM and idle air control motor. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. Perform TEST VER-5A .
  13. Ensure connector is still disconnected at idle air control motor. Using ohmmeter, check resistance between ground and terminal No. 3 (Brown/White wire) on connector for idle air control motor. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Brown/White wire between PCM and idle air control motor. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. Perform TEST VER-5A .
  14. Start engine and allow engine to idle. Using voltmeter, check voltage at terminal No. 3 (Brown/White wire) on connector for idle air control motor. If voltage is more than 5 volts at any time, go to step  33. If voltage is not more than 5 volts at any time, go to step  43.
  15. Turn ignition off. Ensure connector is still disconnected at idle air control motor. Using ohmmeter, check resistance between ground and terminal No. 2 (Yellow/Black wire) on connector for idle air control motor. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Yellow/Black wire between PCM and idle air control motor. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. Perform TEST VER-5A .
  16. Ensure connector is still disconnected at idle air control motor and ignition is off. Using ohmmeter, check resistance between ground and terminal No. 3 (Brown/White wire) on connector for idle air control motor. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Brown/White wire between PCM and idle air control motor. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. Perform TEST VER-5A .
  17. Ensure ignition is off. Disconnect connectors at PCM. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly.
  18. Using ohmmeter, check resistance between terminal No. 2 (Yellow/Black wire) on connector for idle air control motor and PCM connector terminal No. 49 (Yellow/Black wire). If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, repair open circuit on Yellow/Black wire between PCM and idle air control motor. Perform TEST VER-5A .
  19. Inspect PCM connectors for corroded, pushed out, miswired or damaged terminals. If terminals are not corroded, pushed out, miswired or damaged, replace PCM. Perform TEST VER-5A . If terminals are corroded, pushed out, miswired or damaged, repair connectors as necessary. Perform TEST VER-5A .
  20. Turn ignition off. Ensure connector is still disconnected at idle air control motor. Using ohmmeter, check resistance between ground and terminal No. 4 (Violet/Black wire) on connector for idle air control motor. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Violet/Black wire between PCM and idle air control motor. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. Perform TEST VER-5A .
  21. Ensure connector is disconnected at idle air control motor. Using ohmmeter, check resistance between ground and terminal No. 1 (Gray/Red wire) on connector for idle air control motor. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Gray/Red wire between PCM and idle air control motor. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. Perform TEST VER-5A .
  22. Ensure ignition is off. Disconnect connectors at PCM. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly.
  23. Using ohmmeter, check resistance between terminal No. 1 (Gray/Red wire) on connector for idle air control motor and PCM connector terminal No. 57 (Gray/Red wire). If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, repair open circuit on Gray/Red wire between PCM and idle air control motor. Perform TEST VER-5A .
  24. Using ohmmeter, check resistance between ground and terminal No. 2 (Yellow/Black wire) on connector for idle air control motor. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Yellow/Black wire between PCM and idle air control motor. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. Perform TEST VER-5A .
  25. Inspect PCM connectors for corroded, pushed out, miswired or damaged terminals. If terminals are not corroded, pushed out, miswired or damaged, go to step  58. If terminals are corroded, pushed out, miswired or damaged, repair connectors as necessary. Perform TEST VER-5A .
  26. Turn ignition off. Disconnect connector at idle air control motor. Idle air control motor is mounted on the throttle body and contains a 4-pin connector. Start engine and allow engine to idle. Using voltmeter, check voltage at terminal No. 1 (Gray/Red wire) on connector for idle air control motor. If voltage is more than 5 volts at any time, go to next step. If voltage is not more than 5 volts at any time, go to step  52.
  27. Turn ignition off. Using ohmmeter, check resistance between ground and terminal No. 4 (Violet/Black wire) on connector for idle air control motor. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Violet/Black wire between PCM and idle air control motor. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. Perform TEST VER-5A .
  28. Start engine and allow engine to idle. Using voltmeter, check voltage at terminal No. 2 (Yellow/Black wire) on connector for idle air control motor. If voltage is more than 5 volts at any time, go to next step. If voltage is not more than 5 volts at any time, go to step  46.
  29. Turn ignition off. Using ohmmeter, check resistance between ground and terminal No. 1 (Gray/Red wire) on connector for idle air control motor. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Gray/Red wire between PCM and idle air control motor. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. Perform TEST VER-5A .
  30. Using ohmmeter, check resistance between ground and terminal No. 2 (Yellow/Black wire) on connector for idle air control motor. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Yellow/Black wire between PCM and idle air control motor. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. Perform TEST VER-5A .
  31. Start engine and allow engine to idle. Using voltmeter, check voltage at terminal No. 3 (Brown/White wire) on connector for idle air control motor. If voltage is more than 5 volts at any time, go to next step. If voltage is not more than 5 volts at any time, go to step  42.
  32. Turn ignition off. Using ohmmeter, check resistance between ground and terminal No. 3 (Brown/White wire) on connector for idle air control motor. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Brown/White wire between PCM and idle air control motor. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. Perform TEST VER-5A .
  33. Start engine and allow engine to idle. Using voltmeter, check voltage at terminal No. 4 (Violet/Black wire) on connector for idle air control motor. If voltage is more than 5 volts at any time, go to next step. If voltage is not more than 5 volts at any time, go to step  39.
  34. Turn ignition off. Disconnect connectors at PCM. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly.
  35. Inspect PCM connectors for corroded, pushed out, miswired or damaged terminals. If terminals are not corroded, pushed out, miswired or damaged, go to next step. If terminals are corroded, pushed out, miswired or damaged, repair connectors as necessary. Perform TEST VER-5A .
  36. Ensure connectors are still disconnected at PCM and idle air control motor. Using ohmmeter, check resistance between terminal No. 1 (Gray/Red wire) on connector for idle air control motor and each remaining terminal on the connector for idle air control motor. This checks for a short between idle air control motor driver circuits. If resistance is 5 ohms or more on all idle air control motor driver circuits, go to next step. If resistance is less than 5 ohms on any idle air control motor driver circuit, repair idle air control motor driver circuits that are shorted together. Perform TEST VER-5A .
  37. Ensure connectors are still disconnected at PCM and idle air control motor. Using ohmmeter, check resistance between terminal No. 2 (Yellow/Black wire) and terminals No. 3 (Brown/White wire) and No. 4 (Violet/Black wire) on connector for idle air control motor. If resistance is 5 ohms or more on idle air control motor driver circuits, go to next step. If resistance is less than 5 ohms on any idle air control motor driver circuit, repair idle air control motor driver circuits that are shorted together. Perform TEST VER-5A .
  38. Ensure connectors are still disconnected at PCM and idle air control motor. Using ohmmeter, check resistance between terminals No. 3 (Brown/White wire) and No. 4 (Violet/Black wire) on connector for idle air control motor. If resistance is less than 5 ohms on idle air control motor driver circuit, repair idle air control motor driver circuits that are shorted together. Perform TEST VER-5A . If resistance is 5 ohms or more on idle air control motor driver circuit, replace idle air control motor. Perform TEST VER-5A .
  39. Turn ignition off. Disconnect connectors at PCM. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly.
  40. Using ohmmeter, check resistance between terminal No. 4 (Violet/Black wire) on connector for idle air control motor and PCM connector terminal No. 58 (Violet/Black wire). If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, repair open circuit on Violet/Black wire between PCM and idle air control motor. Perform TEST VER-5A .
  41. Inspect PCM connectors for corroded, pushed out, miswired or damaged terminals. If terminals are not corroded, pushed out, miswired or damaged, replace PCM. Perform TEST VER-5A . If terminals are corroded, pushed out, miswired or damaged, repair connectors as necessary. Perform TEST VER-5A .
  42. Turn ignition off. Using ohmmeter, check resistance between ground and terminal No. 3 (Brown/White wire) on connector for idle air control motor. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Brown/White wire between PCM and idle air control motor. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. Perform TEST VER-5A .
  43. Turn ignition off. Disconnect connectors at PCM. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly.
  44. Using ohmmeter, check resistance between terminal No. 3 (Brown/White wire) on connector for idle air control motor and PCM connector terminal No. 48 (Brown/White wire). If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, repair open circuit on Brown/White wire between PCM and idle air control motor. Perform TEST VER-5A .
  45. Inspect PCM connectors for corroded, pushed out, miswired or damaged terminals. If terminals are not corroded, pushed out, miswired or damaged, replace PCM. Perform TEST VER-5A . If terminals are corroded, pushed out, miswired or damaged, repair connectors as necessary. Perform TEST VER-5A .
  46. Turn ignition off. Using ohmmeter, check resistance between ground and terminal No. 1 (Gray/Red wire) on connector for idle air control motor. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Gray/Red wire between PCM and idle air control motor. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. Perform TEST VER-5A .
  47. Using ohmmeter, check resistance between ground and terminal No. 2 (Yellow/Black wire) on connector for idle air control motor. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Yellow/Black wire between PCM and idle air control motor. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. Perform TEST VER-5A .
  48. Ensure ignition is off. Disconnect connectors at PCM. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly.
  49. Using ohmmeter, check resistance between terminal No. 2 (Yellow/Black wire) on connector for idle air control motor and PCM connector terminal No. 49 (Yellow/Black wire). If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, repair open circuit on Yellow/Black wire between PCM and idle air control motor. Perform TEST VER-5A .
  50. Inspect PCM connectors for corroded, pushed out, miswired or damaged terminals. If terminals are not corroded, pushed out, miswired or damaged, go to next step. If terminals are corroded, pushed out, miswired or damaged, repair connectors as necessary. Perform TEST VER-5A .
  51. Using ohmmeter, check resistance between ground and terminal No. 3 (Brown/White wire) on connector for idle air control motor. If resistance is 5 ohms or more, replace PCM. Perform TEST VER-5A . If resistance is less than 5 ohms, repair short to ground on Brown/White wire between PCM and idle air control motor. Perform TEST VER-5A .
  52. Turn ignition off. Using ohmmeter, check resistance between ground and terminal No. 4 (Violet/Black wire) on connector for idle air control motor. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Violet/Black wire between PCM and idle air control motor. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. Perform TEST VER-5A .
  53. Ensure ignition is off. Disconnect connectors at PCM. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly.
  54. Using ohmmeter, check resistance between terminal No. 1 (Gray/Red wire) on connector for idle air control motor and PCM connector terminal No. 57 (Gray/Red wire). If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, repair open circuit on Gray/Red wire between PCM and idle air control motor. Perform TEST VER-5A .
  55. Inspect PCM connectors for corroded, pushed out, miswired or damaged terminals. If terminals are not corroded, pushed out, miswired or damaged, go to next step. Perform TEST VER-5A . If terminals are corroded, pushed out, miswired or damaged, repair connectors as necessary. Perform TEST VER-5A .
  56. Using ohmmeter, check resistance between ground and terminal No. 1 (Gray/Red wire) on connector for idle air control motor. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Gray/Red wire between PCM and idle air control motor. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. Perform TEST VER-5A .
  57. Using ohmmeter, check resistance between ground and terminal No. 2 (Yellow/Black wire) on connector for idle air control motor. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Yellow/Black wire between PCM and idle air control motor. PCM is located at driver's side front corner of engine compartment, just below air cleaner assembly. Perform TEST VER-5A .
  58. Using ohmmeter, check resistance between ground and terminal No. 3 (Brown/White wire) on connector for idle air control motor. If resistance is 5 ohms or more, replace PCM. Perform TEST VER-5A . If resistance is less than 5 ohms, repair short to ground on Brown/White wire between PCM and idle air control motor. Perform TEST VER-5A .
scientia non olet · About Mike's Workshop Manuals