Fastener Specifications (Off-Vehicle)
Single Use Non-Threaded Fasteners/Components
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
|---|
| Application |
| 1-2-3-4 Low and Reverse Clutch Fluid Passage Seal |
| 1-2-3-4-5-6 Clutch Piston Seal |
| 1-2-3-4-5-6 Clutch Piston Inner Seal |
| 3-5-Reverse Clutch Piston Dam Seal |
| 3-5-Reverse Clutch Piston Inner Seal |
| 3-5-Reverse and 4-5-6 Clutch Fluid Seal Ring |
| 4-5-6 Clutch Piston Dam Seal |
| 4-5-6 Clutch Piston Inner Seal |
| 4th Clutch Piston Inner Seal |
| 4th Clutch Piston Outer Seal |
| Accumulator Bypass Valve Seal |
| Automatic Transmission Case Seal |
| Automatic Transmission Fluid Filter |
| Automatic Transmission Fluid Filter Seal |
| Automatic Transmission Fluid Pump Gasket |
| Automatic Transmission Fluid Pump Seal |
| Automatic Transmission Fluid Pump Shaft Seal |
| Body Side Wiring Harness Opening Seal |
| Control Valve Body Gasket |
| Control Valve Body Spacer Plate |
| Control Valve Body Spacer Plate Retainer |
| Drive Link Lubricant Fluid Seal |
| Fluid Transfer Pipe Seal |
| Front Wheel Drive Shaft Oil Seal |
| Manual Shaft Detent Lever Hub Pin |
| Manual Shift Shaft Seal |
| Park Pawl Actuator Guide Pin |
| Torque Converter Fluid Seal |
| Torque Converter Housing Gasket |
| Turbine Shaft Seal |
Single Use Threaded Fastener/Component Tightening Specifications
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
||||
|---|---|---|---|---|
| Application | Ref No.* | Quantity | Size | Specification |
| Metric (English) | ||||
| Automatic Transmission Fluid Pump Cover Bolt Refer to procedure for tightening sequence and torque values. |
211 | 19 | M6 x 25 | Transmission Fluid Pump, Front Differential Carrier Baffle, and Front Differential Ring Gear Installation |
| *Reference number refers to the component callout number in Disassembled Views | ||||
Reusable Threaded Fastener Tightening Specifications
|
NOTE:
All fasteners listed in this table can be reused after removal. |
||||
|---|---|---|---|---|
| Application | Ref No.* | Quantity | Size | Specification |
| Metric (English) | ||||
| Accumulator Valve Body Bolt | 33 | 2 | M4 x.7 | 2.75 N.m (24 lb in) |
| Automatic Transmission Au x iliary Fluid Accumulator Bolt | 9 | 3 | M8 x 30 | 22 N.m (16 lb ft) |
| Automatic Transmission Case Hole Plug | 68 | 1 | 1/8" - 27 NPTF | 12 N.m (106 lb in) |
| Automatic Transmission Fluid Level Hole Plug | 65 | 1 | 1/8" - 27 NPTF | 12 N.m (106 lb in) |
| Automatic Transmission Fluid Pan Drain Plug | 66 | 1 | 1/8" - 27 NPTF | 12 N.m (106 lb in) |
| Automatic Transmission Fluid Filter Cover Bolt | 58 | 3 | M6 x 20 | 9 N.m (80 lb in) |
| Automatic Transmission Fluid Pump Cover Bolt Refer to procedure for tightening sequence and torque values. |
200 | 22 | M6 x 30 | Transmission Fluid Pump, Front Differential Carrier Baffle, and Front Differential Ring Gear Installation |
| Automatic Transmission Fluid Pump Cover Bolt | 312 | 5 | M6 x 25 | 9 N.m (80 lb in) |
| Automatic Transmission Input Speed Sensor Bolt | 69 | 1 | M6 x 25 | 9 N.m (80 lb in) |
| Automatic Transmission Output Speed Sensor Bolt | 711 | 1 | M6 x 25 | 9 N.m (80 lb in) |
| Control Valve Body Bolt Refer to procedure for tightening sequence and torque values. |
24 | 4 | M5 x 55 | Control Valve Body Assembly Installation |
| Control Valve Body Bolt Refer to procedure for tightening sequence and torque values. |
25 | 1 | M5 x 37 | Control Valve Body Assembly Installation |
| Control Valve Body Bolt Refer to procedure for tightening sequence and torque values. |
5 | 3 | M5 x 65 | Control Valve Body Assembly Installation |
| Control Valve Body Bolt | 6 | 9 | M5 x 85 | Control Valve Body Assembly Installation |
| Control Valve Body Bolt | 7 | 8 | M5 x 94 | Control Valve Body Assembly Installation |
| Control Valve Body Cover Bolt | 1 | 6 | M6 x 30 | Control Valve Body Cover Installation |
| Control Valve Body Cover Stud Refer to procedure for tightening sequence and torque values. |
2 | 6 | M6 x 30 | Control Valve Body Cover Installation |
| Control Valve Solenoid Body Bolt | 30 | 1 | - | 9 N.m (80 lb in) |
| Control Valve Solenoid Body Bolt | 433 | 4 | M5 x 55 | 8 N.m (71 lb in) |
| Control Valve Solenoid Body Bolt | 499 | 2 | M5 x 21 | 8 N.m (71 lb in) |
| Fluid Transfer Pipe Bolt | 21 | 1 | M6 x 25 | 8 N.m (71 lb in) |
| Front Differential Carrier Baffle Bolt | 204 | 2 | M6 x 18.5 | 9 N.m (80 lb in) |
| Front Differential Carrier Baffle Bolt - Case |
62 | 2 | M6 x 18.5 | 9 N.m (80 lb in) |
| Input Shaft Support Bolt | 55 | 3 | M6 x 50 | 12 N.m (106 lb in) |
| Manual Shift Detent Lever Spring Bolt | 20 | 1 | M6 x 25 | 9 N.m (80 lb in) |
| Overdrive and Reaction Carrier Bolt | 535 | 3 | M6 x 35 | 9 N.m (80 lb in) |
| Automatic Transmission Case Hole Plug | 76 | 1 | M8 x 16.25 | 40 N.m (30 lb ft) |
| Automatic Transmission Fluid Pressure Test Hole Plug | 53 | 1 | 1/8" - 27 NPTF | 12 N.m (106 lb in) |
| Torque Converter and Differential Housing Bolt Refer to procedure for tightening sequence and torque values. |
16 | 14 | M8 x 30 | Torque Converter Housing with Fluid Pump Assembly Installation |
| *Reference number refers to the component callout number in Disassembled Views | ||||