Fastener Specifications (Off Vehicle)
Single Use Non-Threaded Fasteners/Components
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
|---|
| Application |
| 1 - 2 - 3 - 4 Clutch Piston Inner Seal |
| 1 - 2 - 3 - 4 and 3 - 5 Reverse Clutch Housing Thrust Washer |
| 3 - 5 Reverse Clutch Bearing |
| Case Extension Seal |
| Center Support Fluid Passage Seal |
| Fluid Filter |
| Fluid Filter Seal Assembly |
| Filter Plate Assembly |
| Fluid Pump Seal |
| Manual Shift Shaft Pin |
| Manual Shaft Detent Lever Hub Pin |
| Turbine Shaft (O-Ring) Seal |
Single Use Threaded Fastener/Component Tightening Specifications
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
||||
|---|---|---|---|---|
| Application | Reference number from Disassembled Views | Quantity | Size | Specification |
| Metric (English) | ||||
| Front Prop Shaft Flange Nut | 39 | 1 | - | 55 N.m (41 lb ft) |
Reusable Threaded Fastener Tightening Specifications
|
NOTE:
All fasteners listed in this table can be reused after removal. |
||||
|---|---|---|---|---|
| Application | Reference number from Disassembled Views | Quantity | Size | Specification |
| Metric (English) | ||||
| Case Extension | ||||
| Case Extension to Case Assembly | 16 | 6 | M10 x1.5 x 40 | 55 N.m (41 lb ft) |
| Transfer Case Adapter | 16 | 7 | M10 x1.5 x 40 | 55 N.m (41 lb ft) |
| Control Solenoid Valve Assembly and Control Valve Lower Body Assembly to Control Valve Upper Body Assembly | 310 | 6 | M5 x 0.8 x 55 | 8 N.m (71 lb in) |
| Control Solenoid Valve Assembly and Control Valve Lower Body Assembly to Control Valve Upper Body Assembly | 309 | 10 | M5 x 0.8 x 45 | 8 N.m (71 lb in) |
| Control Solenoid Valve Heat Sink to Valve Body | 312 | 2 | M5 x 0.8 x 53 | 8 N.m (71 lb in) |
| Control Valve Upper Body Assembly to Control Valve Lower Body Assembly | 301 | 12 | M5 x 0.8 x 36 | 8 N.m (71 lb in) |
| Control (with Body and Valve) Valve Assembly to Case Assembly | 22 | 6 | M5 x 0.8 x 73 | 8 N.m (71 lb in) |
| Fluid Pan Assembly to Case Assembly (6L80) | 30 | 18 | M6 x 1.0 x 20 | 9 N.m (80 lb in) |
| Fluid Pan Assembly to Case Assembly (6L50) | 30 | 17 | M6 x 1.0 x 20 | 9 N.m (80 lb in) |
| Fluid Pump Cover Assembly to Torque Converter Housing | 231 | 13 | M6 x 1.0 x 40 | 11 N.m (97 lb in) |
| Front Prop Shaft Flange Nut to Output Shaft | 39 | 1 | M22 x 1.5 x 14 | 55 N.m (41 lb ft) |
| Input and Output Speed Sensor Assembly to Control Valve Upper Body Assembly | 302 | 2 | M6 x 1.0 x 20 | 12 N.m (106 lb in) |
| Line Pressure Test Hole Plug to Torque Converter Housing | 202 | 1 | 1/8"-27 NPTF | 11 N.m (97 lb in) |
| Manual Shaft Detent Assembly to Valve Body | 23 | 1 | M6 x 1.0 x 14.5 | 12 N.m (106 lb in) |
| Torque Converter Housing Assembly to Case Assembly (6L50) | 3 | 8 | M8 x 1.5 x 50 | 31 N.m (23 lb ft) |
| Torque Converter Housing Assembly to Case Assembly (6L80) | 3 | 9 | M10 x 1.5 x 50 | 72 N.m (53 lb ft) |
| Transmission Cover Bolt | 42 | 2 | - | 12 N.m (106 lb in) |
| Transmission Oil Level Check Plug to Fluid Pan Assembly - M6 | 31 | 1 | M6x 1.75 | 9 N.m (80 lb in) |
| Transmission Oil Level Check Plug to Fluid Pan Assembly - M12 | 31 | 1 | M12 x 1.75 | 25 N.m (18 lb ft) |