Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Chevrolet >> 2019 >> Cruze L >> Repair and Diagnosis >> External Pages >> Different car >> Section 112 (Secondary And Configurable Customer Control System) >> Diagnostic Information and Procedures >> Steering Wheel Controls Malfunction >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different car, the 2018 Chevrolet Cruze. However, it is still accessible from the selected car via links, so may be relevant.

All Controls Malfunction

  1. Ignition OFF, disconnect the harness connector at the S70R Steering Wheel Controls Switch - Right. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 1 and ground.
    • If greater than 10 Ω 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 Ω 
  3. Ignition ON.
  4. Verify that a test lamp illuminates between the B+ circuit terminal 12 and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the control circuit end to end.
      • If greater than 2 Ω, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is not open and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition OFF.
    2. Test for infinite resistance between the B+ circuit terminal 12 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the S70R Steering Wheel Controls Switch - Right.
    • Go to next step: If the test lamp illuminates 
  5. Test for 2 - 10 V between the serial data circuit terminal 2 and ground.
    • If less than 2 V 
    1. Ignition OFF, disconnect the harness connector at the P16 Instrument Cluster.
    2. Test for infinite resistance between the serial data circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the serial data circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the P16 Instrument Cluster.
    • If greater than 10 V 
    1. Ignition OFF, disconnect the harness connector at the P16 Instrument Cluster, ignition ON.
    2. Test for less than 1 V between the serial data circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the P16 Instrument Cluster.
      • Go to next step: If between 2 - 10 V 
  6. Test or replace S70R Steering Wheel Controls Switch - Right

S70F Steering Wheel Controls Switch - Radio Volume

  1. Ignition OFF and all vehicle systems OFF, disconnect the harness connector at the S70F Steering Wheel Controls Switch - Radio Volume. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 3 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 Ω 
  3. Ignition ON.
  4. Test for greater than 4.5 V between the signal circuit terminals listed below and ground:
    • Terminal 1
    • Terminal 2
    • If 4.5 V or less 
    1. Ignition OFF, disconnect the harness connector at the S70R Steering Wheel Controls Switch - Right.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, test or replace the S70R Steering Wheel Controls Switch - Right.
    • Go to next step: If greater than 4.5 V 
  5. Install a 3 A fused jumper wire between the signal circuit terminal 1 and the ground circuit terminal 3.
  6. Verify the radio volume decreases.
    • If the volume does not decrease 

      Test or replace the S70R Steering Wheel Controls Switch - Right.

    • Go to next step: If the volume decreases 
  7. Remove the jumper wire. Install a 3 A fused jumper wire between the signal circuit terminal 2 and the ground circuit terminal 3.
  8. Verify the volume increases.
    • If the volume does not increase 

      Test or replace the S70R Steering Wheel Controls Switch - Right.

    • Go to next step: If volume increases 
  9. Test or replace the S70F Steering Wheel Controls Switch - Radio Volume.

S70E Steering Wheel Controls Switch - Radio Presets

  1. Ignition OFF and all vehicle systems OFF, disconnect the harness connector at the S70E Steering Wheel Controls Switch - Radio Presets. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 3 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 Ω 
  3. Ignition ON.
  4. Test for greater than 4.5 V between the signal circuit terminals listed below and ground:
    • Terminal 1
    • Terminal 2
    • If 4.5 V or less 
    1. Ignition OFF, disconnect the harness connector at the S70R Steering Wheel Controls Switch - Right.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, test or replace the S70R Steering Wheel Controls Switch - Right.
    • Go to next step: If greater than 4.5 V 
  5. Install a 3 A fused jumper wire between the signal circuit terminal 1 and the ground circuit terminal 3.
  6. Verify the radio changes presets.
    • If radio does not change presets 

      Test or replace the S70R Steering Wheel Controls Switch - Right.

    • Go to next step: If radio changes presets 
  7. Remove the jumper wire. Install a 3 A fused jumper wire between the signal circuit terminal 2 and the ground circuit terminal 3.
  8. Verify the radio changes presets.
    • If radio does not change presets 

      Test or replace the S70R Steering Wheel Controls Switch - Right.

    • Go to next step: If radio changes presets 
  9. Test or replace the S70E Steering Wheel Controls Switch - Radio Presets.
scientia non olet · About Mike's Workshop Manuals