Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Chevrolet >> 2018 >> Cruze LS, Automatic Trans >> Repair and Diagnosis >> Accessories & Equipment >> Drivers Assistance Systems - ADAS >> Image Display Camera System >> Diagnostic Information and Procedures >> Rear Vision Camera System Malfunction (Hatchback with IO5/IO6) >> Circuit/System Testing

Circuit/System Testing

NOTE:

Circuit/System Verification must be performed before Circuit/System Testing.

  1. Ignition OFF, disconnect the harness connector at the B87 Rearview Camera.
  2. Test for less than 10 Ω between the ground circuit terminal 4 and ground.
    • If 10 Ω or greater 

      Test for less than 2 Ω in the ground circuit end to end.

    • If 2 Ω or greater, repair the open/high resistance in the circuit.
    • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 Ω 
  3. Ignition ON.
  4. Verify a test lamp illuminates between the ignition circuit terminal 5 and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ignition circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is OK and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition OFF.
    2. Test for infinite resistance between the ignition circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, test or replace the KR73 Ignition Main Relay.
    • Go to next step: If the test lamp illuminates 
  5. Ignition OFF, disconnect the K74 Human Machine Interface Control Module X1 harness connector. Ignition ON.
  6. Verify a test lamp illuminates between serial data communication enable circuit terminal 5 and ground.
    • If the test lamp does not illuminate 
    1. Ignition/Vehicle OFF.
    2. Test for infinite resistance between the serial data communication enable circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the serial data communication enable circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the control module that controls the serial data communication enable circuit.
    • Go to next step: If the test lamp illuminates 
  7. Ignition OFF, Connect the K74 Human Machine Interface Control Module X1 harness connector.
  8. Disconnect the X2 harness connector at the K74 Human Machine Interface Control Module, ignition ON.
  9. Test for less than 1 V between the signal circuit terminal listed below and ground:
    • Signal (+) circuit terminal 1 at the B87 Rearview Camera.
    • Signal (-) circuit terminal 2 at the B87 Rearview Camera.
    • If 1 V or greater 

      Repair the short to voltage on the circuit.

    • Go to next step: If less than 1 V 
  10. Test for infinite resistance between the signal circuit terminal listed below and ground:
    • Signal (+) circuit terminal 1 at the B87 Rearview Camera.
    • Signal (-) circuit terminal 2 at the B87 Rearview Camera.
    • If less than infinite resistance 

      Repair the short to ground on the circuit.

    • Go to next step: If infinite resistance 
  11. Test for less than 2 Ω in the signal (+) circuit end to end.
    • If 2 Ω or greater 

      Repair the open/high resistance in the circuit.

    • Go to next step: If less than 2 Ω 
  12. Test for less than 2 Ω in the signal (-) circuit end to end.
    • If 2 Ω or greater 

      Test the signal circuit for an open/high resistance.

    • Go to next step: If less than 2 Ω 
  13. Replace the B87 Rearview Camera.
  14. Engine running, parking brake applied, transmission in REVERSE, verify a clear rear vision image is displayed on the A11 Radio.
    • If a clear rear vision image is not displayed on the A11 Radio 

      Replace the K74 Human Machine Interface Control Module.

    • Go to next step: If a clear rear vision image displayed on the A11 Radio 
  15. All OK.
scientia non olet · About Mike's Workshop Manuals