Mike's Workshop Manuals: Service manuals for every vehicle
Home >> Chevrolet >> 2017 >> Sonic Premier, 4D Hatchback, Automatic Trans >> Repair and Diagnosis >> Body & Frame >> Ignition Switch/Steering Lock >> Diagnostic Information And Procedures >> Diagnostic Information and Procedures >> Power Mode Mismatch >> Circuit/System Testing

Circuit/System Testing

Diagnostic A

  1. Ignition OFF and all vehicle systems OFF, disconnect the KR32E Blower Motor Relay. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 1 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Ignition ON.
  4. Verify a test lamp illuminates between the B+ circuit terminal 3 and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition OFF, remove the test lamp.
    2. Test for less than 2 Ω in the B+ circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is good and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition OFF, remove the test lamp.
    2. Test for infinite resistance between the ignition circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the KR32E Blower Motor Relay.
    • If the test lamp illuminates 
  5. Connect a test lamp between the control circuit terminal 2 and the ground circuit terminal 1.
  6. Verify the test lamp turns ON and OFF when commanding the Auxiliary Ignition Run Relay On and Off with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, remove the test lamp, disconnect the harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, remove the test lamp, disconnect the harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • If the test lamp turns ON and OFF 
  7. Verify that a test lamp does not illuminate between the ignition circuit terminal 5 and ground.
    • If the test lamp illuminates 

      Repair the short to voltage on the ignition circuit.

    • If the test lamp does not illuminate 
  8. Ignition ON, connect a 40 A fused jumper wire between the B+ circuit terminal 3 and the ignition control circuit terminal 5.
  9. Verify the M8 Blower Motor is activated.
    • If the M8 Blower Motor does not activate 
    1. Ignition OFF, disconnect the harness connector at the M8 Blower Motor.
    2. Test for infinite resistance between the ignition circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the ignition circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the device.
    • If the M8 Blower Motor activates 
  10. Test or replace the KR32E Blower Motor Relay.

Diagnostic B

  1. Ignition OFF and all vehicle systems OFF, disconnect the KR73 Ignition Main Relay. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 85 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Ignition ON.
  4. Verify a test lamp illuminates between the B+ circuit terminal 30 and ground.
    • If the test lamp does not illuminate 

      Replace the X50A Fuse Block - Underhood

    • If the test lamp illuminates 
  5. Connect a test lamp between the control circuit terminal 86 and the ground circuit terminal 85.
  6. Verify the test lamp turns ON and OFF when commanding the Ignition Run/Crank Relay On and Off with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, remove the test lamp, disconnect the harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, remove the test lamp, disconnect the harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • If the test lamp turns ON and OFF 
  7. Verify that a test lamp does not illuminate between the ignition circuit terminal 87 and ground.
    • If the test lamp illuminates 

      Repair the short to voltage on the ignition circuit

    • If the test lamp does not illuminate 
  8. Ignition ON, connect a 40 A fused jumper wire between the B+ circuit terminal 30 and the ignition circuit terminal 87.
  9. Verify device is activated.
    • If the device does not activate 
    1. Ignition OFF, disconnect the harness connector at the device.
    2. Test for infinite resistance between the ignition circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the ignition circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the device.
    • If the device activates 
  10. Test or replace the KR73 Ignition Main Relay.

Diagnostic C

  1. Ignition OFF and all vehicle systems OFF, disconnect the KR75 Engine Controls Ignition Relay, ignition ON.
  2. Verify a test lamp illuminates between the B+ circuit terminal 30 and ground.
    • If the test lamp does not illuminate 

      Replace the X50A Fuse Block - Underhood

    • If the test lamp illuminates 
  3. Verify a test lamp illuminates between the B+ circuit terminal 85 and ground.
    • If the test lamp does not illuminate 

      Replace the X50A Fuse Block - Underhood

    • If the test lamp illuminates 
  4. Connect a test lamp between the B+ circuit terminal 85 and the control circuit terminal 86.
  5. Verify the test lamp turns ON and OFF when switching the ignition ON and OFF.
    • If the test lamp is always OFF 
    1. Ignition OFF, remove the test lamp, disconnect the harness connector at the K20 Engine Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Ignition OFF.
    4. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, remove the test lamp, disconnect the harness connector at the K20 Engine Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K20 Engine Control Module.
    • If the test lamp turns ON and OFF 
  6. Verify a test lamp does not illuminate between the ignition circuit terminal 87 and ground.
    • If the test lamp illuminates 

      Repair the short to voltage on the circuit.

    • If the test lamp does not illuminate 
  7. Ignition ON, connect a 40 A fused jumper wire between the B+ circuit terminal 30 and the ignition circuit terminal 87.
  8. Verify device is activated.
    • If the device does not activate 
    1. Ignition OFF, disconnect the harness connector at the device.
    2. Test for infinite resistance between the ignition circuit terminal 87 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the ignition circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the device.
    • If the device activates 
  9. Test or replace the KR75 Engine Controls Ignition Relay.

Diagnostic D (Without BTM)

  1. Ignition OFF and all vehicle systems OFF, disconnect the KR76 Retained Accessory Power Relay. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 2 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Ignition ON.
  4. Verify a test lamp illuminates between the B+ circuit terminal 3 and ground.
    • If the test lamp does not illuminate 

      Replace the X51A Fuse Block - Instrument Panel

    • If the test lamp illuminates 
  5. Connect a test lamp between the control circuit terminal 1 and the ground circuit terminal 2.
  6. Verify the test lamp turns ON and OFF when commanding the Accessory/Retained Accessory Power Relay On and Off with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, remove the test lamp, disconnect the harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, remove the test lamp, disconnect the harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • If the test lamp turns ON and OFF 
  7. Verify that a test lamp does not illuminate between the ignition circuit terminal 5 and ground.
    • If the test lamp illuminates 

      Repair the short to voltage on the ignition circuit

    • If the test lamp does not illuminate 
  8. Ignition ON, connect a 40 A fused jumper wire between the B+ circuit terminal 3 and the ignition circuit terminal 5.
  9. Verify device is activated.
    • If the device does not activate 
    1. Ignition OFF, disconnect the harness connector at the device.
    2. Test for infinite resistance between the ignition circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the ignition circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the device.
    • If the device activates 
  10. Test or replace the KR76 Retained Accessory Power Relay.

Diagnostic D (With BTM)

  1. Ignition OFF and all vehicle systems OFF, disconnect the KR76 Retained Accessory Power Relay. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 2 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Ignition ON.
  4. Verify a test lamp illuminates between the B+ circuit terminal 3 and ground.
    • If the test lamp does not illuminate 

      Replace the X51A Fuse Block - Instrument Panel

    • If the test lamp illuminates 
  5. Connect a test lamp between the control circuit terminal 1 and the ground circuit terminal 2.
  6. Verify the test lamp turns ON and OFF when cycling the ignition between ON and OFF.
    • If the test lamp is always OFF 
    1. Ignition OFF, remove the test lamp, disconnect the harness connector at the K84 Keyless Entry Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K84 Keyless Entry Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, remove the test lamp, disconnect the harness connector at the K84 Keyless Entry Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K84 Keyless Entry Control Module.
    • If the test lamp turns ON and OFF 
  7. Verify that a test lamp does not illuminate between the ignition circuit terminal 5 and ground.
    • If the test lamp illuminates 

      Repair the short to voltage on the ignition circuit

    • If the test lamp does not illuminate 
  8. Ignition ON, connect a 40 A fused jumper wire between the B+ circuit terminal 3 and the ignition circuit terminal 5.
  9. Verify device is activated.
    • If the device does not activate 
    1. Ignition OFF, disconnect the harness connector at the device.
    2. Test for infinite resistance between the ignition circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the ignition circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the device.
    • If the device activates 
  10. Test or replace the KR76 Retained Accessory Power Relay.
scientia non olet · About Mike's Workshop Manuals