Fastener Specifications (Off Vehicle)
Single Use Non-Threaded Fasteners/Components
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
|---|
| Application |
| 1-2-3-4 and 3-5-Reverse Clutch Housing Thrust Washer |
| 1-2-3-4 Clutch Piston Inner Seal |
| 1-2-3-4 and 3-5-Reverse Clutch Bearing |
| Automatic Transmission Fluid Filter |
| Automatic Transmission Fluid Pump Seal at Torque Converter Housing |
| Automatic Transmission Fluid Pump Seal at Automatic Transmission Case |
| Automatic Transmission Wiring Connector Seal |
| Automatic Transmission Wiring Connector Seal - O-Ring |
| Case Extension Seal |
| Center Support Fluid Passage Seal |
| Filter Plate Assembly |
| Turbine Shaft Seal- - O-Ring |
Single Use Threaded Fastener/Component Tightening Specifications
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
||||
|---|---|---|---|---|
| Application | Reference number from Disassembled Views | Quantity | Size | Specification |
| Metric (English) | ||||
| Front Prop Shaft Flange Nut at Output Shaft-6L50 | 39 | 1 | M22x1.5x14 | 55 N.m (41 lb ft) |
| Front Prop Shaft Flange Nut at Output Shaft-6L80 | 105 N.m (77 lb ft) | |||
Reusable Threaded Fastener Tightening Specifications
|
NOTE:
All fasteners listed in this table can be reused after removal. |
|||||
|---|---|---|---|---|---|
| Application | Reference number from Disassembled Views | Quantity | Size | Specification | |
| Metric (English) | |||||
| Automatic Transmission Fluid Pan at Automatic Transmission Case - 6L50 | 30 | 17 | M6x1.0x20 | 9 N.m (80 lb in) | |
| Automatic Transmission Fluid Pan at Automatic Transmission Case - 6L80 | 30 | 18 | M6x1.0x20 | 9 N.m (80 lb in) | |
| Automatic Transmission Fluid Pump Cover Bolt at Torque Converter Housing | 231 | 13 | M6 1.0x40 | 11 N.m (97 lb in) | |
| Case Extension at Automatic Transmission Case | 16 | 6 | M10x1.5x40 | 55 N.m (41 lb ft) | |
| Control Valve Lower Body at Control Valve Upper Body Assembly | 310 | 6 | M5x0.8x55 | 8 N.m (71 lb in) | |
| Control Valve Lower Body at Control Valve Upper Body Assembly | 309 | 10 | M5x0.8x45 | 8 N.m (71 lb in) | |
| Control Solenoid Valve Heat Sink at Control Valve Body | 312 | 2 | M5x0.8x53 | 8 N.m (71 lb in) | |
| Control Valve Assembly at Automatic Transmission Case | 22 | 6 | M5x0.8x73 | 8 N.m (71 lb in) | |
| Control Valve Upper Body Assembly at Control Valve Lower Body | 301 | 12 | M5x0.8x36 | 8 N.m (71 lb in) | |
| Input and Output Speed Sensor Assembly at Control Valve Upper Body Assembly | 302 | 2 | M6x1.0x20 | 12 N.m (106 lb in) | |
| Line Pressure Test Hole Plug at Torque Converter Housing | 202 | 1 | 1/8 - 27 NPTF | 11 N.m (97 lb in) | |
| Manual Shaft Detent Assembly at Control Valve Body | 23 | 1 | M6x1.0x14.5 | 12 N.m (106 lb in) | |
| Torque Converter Housing at Automatic Transmission Case - 6L50 | 3 | 8 | M8x1.25x50 | 31 N.m (23 lb ft) | |
| Torque Converter Housing at Automatic Transmission Case - 6L80 | 3 | 9 | M10x1.5x50 | 72 N.m (53 lb ft) | |
| Transmission Oil Level Check Plug at Automatic Transmission Fluid Pan | 31 | 1 | M12x1.75 | 25 N.m (18 lb ft) | |